| Content |
Shure WL-185 Lavalier Condenser Microphone
Models WL183, WL184 and WL185 are lavalier electret condenser mics designed for use
with a wireless body-pack transmitter. Each mic has a 1.2 meter (4 ft.) cable terminated
with a miniature 4-pin mini connector. Included tie clip can be rotated in 90 degree intervals for placement flexibility.
WL185 (Cardioid):
Recommended for general purpose sound reinforcement applications requiring good rejection of ambient noise.
Use of windscreen highly recommended. Pickup angle: 130 degrees.
Type
Condenser (electret bias)
Frequency Response
50 to 17,000 Hz
Output Impedance
1800 ohms
Sensitivity (1 Pa = 94 dB SPL)
WL183: -40.0 dBV/Pa
WL184: -44.5 dBV/Pa
WL185: -45.5 dBV/Pa
Maximum Sound Pressure Level
WL183: 125.0 dB SPL
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
Output Noise (A-weighted)
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
Dynamic Range
102.5 dB
Polarity
Positive pressure on diaphragm produces positive voltage on pins 3 and 4 relative to pin 1.
Power Requirements
Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) provided at microphone connector pin 2 relative to pin 1 of a Shure wireless microphone transmitter.
|
Miniaturized lavalier condenser microphone for wireless or wired applications.
The ADX10 is a miniaturized condenser microphone designed for lavaliere applications such as speech, presentation and theatrical production. The ADX10 has the ability to accurately capture and reproduce vocals from a comfortable distance of 4“- 8“. This mic is clear, resistant to feedback and easy to use.
Designed with a uniformly controlled cardioid polar pattern, the ADX10 helps to isolate the area or section being miked from other vocals or instruments on stage. The ADX10 has a smooth, accurate frequency range of 50 Hz - 18 kHz. This mic is lightweight, low profile and has a natural sound with exceptional sound response.
Primarily for use with the Audix RAD360 Wireless System, the ADX10 includes a tie-clip and a 3' attached cable terminating to a mini-XLRf connector.
MODEL VARIATIONS:
ADX10P - For hard wired application. Includes an 8' cable terminating to a mini-XLRf connector tie clip, external windscreen and a phantom power adapter module. 9 - 48 V phantom power required.
| Type | Pre-polarized Condenser |
|---|
| Polar Pattern | Cardioid | | Frequency Response | 50Hz - 18kHz | | Impedance | 250 Ohms | | Sensitivity | 5 mV/Pa @1k |
| Subminiature lavalier design; ideal size for theater, television, broadcasting, video, film, and sound reinforcement
Small, inconspicuous mounting hardware
Full, clear sound comparable to larger microphones
Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
Controlled low-frequency rolloff reduces low-frequency clothing and room noise
Low distortion, wide dynamic range
Uniform omnidirectional polar pattern
Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
Wide-range phantom powering (SM93) accepts all commonly used voltages
Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz
Response Curve Image Small SM93 WL93 View Larger
Polar Pattern
Omnidirectional, uniform with frequency
Output Impedance
3000 ohms
Output Level (1 Pascal = 94 dB SPL)
Open Circuit Voltage: -38 dBV/Pa (13 mV)
Output Clipping Level (at 1,000 Hz)
0.25 V at 120 dB
Total Harmonic Distortion
Less than 1% at 120 dB
Maximum SPL
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL)
18 dB typical, A-weighted
Signal-to-Noise Ratio
76 dB at 94 dB SPL (IEC 651)
Polarity
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
*Produces positive voltage at pin 2 of Shure wireless receiver three-pin connector
Recommended Operating Voltage
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
Current Drain
40 microA typical
Environmental Conditions
Operating Temperatures: -18 to 57 degrees C (0 to 135 degrees F)
Storage Temperatures: -29 to 74 degrees C (-20 to 165 degrees F)
Cable
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type TA4F (WL93T: Tan 1.27 m [4.17 ft])
Case
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Net Weight
Microphone: 16 g (0.57 oz) |
The smartLav+ is a broadcast-grade wearable microphone designed for use in a wide range of film, television and broadcast scenarios, or wherever broadcast quality audio is required in a discreet, portable format without the complication and expense of additional wireless equipment.
With the smartLav+ the user simply mounts the microphone on the talent, connects it to a smartphone or tablet headset jack and records via the RØDE Rec app for iOS, or any other audio app of their choice.
By employing a professional quality omni-directional condenser capsule the smartLav+ picks up sound equally from all around the microphone, allowing for versatility when mounting and ensuring a high degree of user-friendly operation.
A foam pop shield is supplied to minimise wind noise and vocal plosives (hard ʽbʼ, ʽtʼ and ʽpʼ sounds), as well as a durable mounting clip with in-built cable management. Its Kevlar® reinforced cable ensures that you never stretch or snap your microphone under normal usage conditions.
The smartLav+ is compatible with any audio app that accepts input from the headset connection, however it has been designed to pair perfectly with RØDEʼs RØDE Rec app for Apple iOS devices. RØDE Rec turns the userʼs iOS device into a fully-featured field recorder, with a wide range of equalisation presets to suit various recording situations, in addition to professional editing functions and the ability to publish to SoundCloud and Dropbox direct from the app.
Acoustic Principle Pressure Gradient
Active Electronics JFET
Capsule 0.10“
Polar Pattern [Omnidirectional - picks up all sides equally]
Address Type End
Frequency Range 20Hz - 20kHz (selected HPF @ 0)
Output Impedance 0Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -35.0dB re 1 Volt/Pascal (17.80mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 27dB-A
Weight 6.00gm
Dimensions 1180.00mmH x 4.50mmW x 4.50mmD
Dimensions 1180.00mmH x 4.50mmW x 4.50mmD
Output TRRS Output
Warranty 1 year
|
Shure SLX14 Instrument Wireless System Features:
SLX4 Wireless Receiver:
Automatic Frequency Selection
Automatic Transmitter Setup
960 Selectable frequencies across 24MHz bandwidth
Detachable 1/4 wave antennas
Microprocessor-controlled diversity
RF presence LED
5-segment audio meter
Multi-function, backlit LCD
Low battery indicator
Frequency and power lockout
Rugged metal chassis
Volume control on rear of unit
1/2 rack design
Furnished rack hardware
Non-slip bumpers for use out of rack
XLR and 1/4" outputs
SLX1 Bodypack Transmitter
Automatic Transmitter Setup
Backlit LCD with timeout feature
Frequency and power lockout
3-segment battery fuel gauge
2 AA batteries (included) provide 8 hours of continuous use
518 - 782 MHz operating range
Shure SLX14 Instrument Wireless System Specifications:
SLX4 Wireless Receiver:
Audio Output Level (ref. ± 38kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): —13dBV; 1/4" connector (into 3000 Ohm load): —2dBV
Output Impedance: XLR connector: 200 Ohms; 1/4" connector: 1kohms
XLR output: Impedance balanced; Pin 1: Ground; Pin 2: (+); Pin 3: (-)
Sensitivity: —105 dBm for 12 dB SINAD, typical
Image Rejection: >70 dB, typical
Power Requirements: 12—18 Vdc at 150 mA, supplied by external power supply
Operating Range Under Typical Conditions: 300 ft. (100m)
Note: Actual range depends on RF signal absorption, reflection, and interference
Audio Frequency Response (+/— 2 dB): Minimum: 45 Hz: Maximum: 15 kHz
Note: Overall system frequency depends on microphone element.
Total Harmonic Distortion (ref. +/— 38 kHz deviation, 1 kHz tone): 0.5%, typical
Dynamic Range: >100 dB A-weighted
Operating Temperature Range: —18 degree C (0 degree F) to +50 degree C (+122 degree F)
Note: battery characteristics may limit this range
Dimensions (H x W x D): 1.65 x 7.76 x 5.28 in., (42 x 197 x 134 mm)
Weight: 1 lb. 13 oz. (816 g )
Housing: Galvanized steel
Transmitter Audio Polarity: Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with
respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
Logic Connections: Pin 1: Logic output, Transmitter Mute Status. Mute=low (0 V). Sinks up to 100 mA. Absolute maximum -0.7 to 5.5V DC; Pin 2: Logic ground; Pin 3: Logic output, Battery Status. Good=low (0 V). Sinks up to 100 mA; Absolute maximum -0.7 to 5.5V DC
SLX1 Bodypack Transmitter
Audio Input Level: -10 dBV maximum at mic gain position, +10 dBV maximum at 0 dB gain position, +20 dBV maximum at -10 dB gain position
Gain Adjustment Range: 30dB
Input Impedance: 1 Mohms
RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations
Dimensions (H x W x D): 4.25 x 2.50 x 0.75 in. (108 x 64 x 19 mmD)
Weight: 81 grams (3 oz.) without batteries
Housing: Molded ABS case
Power Requirements: 2 "AA" size alkaline or rechargeable batteries
Battery Life: >8 hours (alkaline)
|
This clip-on lavalier mic provides crisp, full-sounding voice pickup. The AT831R also excels as an instrument mic, especially for pickup of acoustic guitar with included AT8444 guitar adapter. The mic is ideal for higher SPL applications. Excellent gain before feedback and suppression of background noise. Operates on phantom power only.
Clip-on lavalier mic also excels in acoustic guitar applications
Provides crisp, full-sounding voice and instrument pickup
Excellent gain before feedback and suppression of background noise
Operates on phantom power only
4.0 m (13.1') cable permanently attached to mic, TA3F connector at power module
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Also available as: AT831b - with battery/phantom power module AT831c - less power module; includes clothing clip and windscreen only; 10' (3 m) cable, unterminated AT831cW - less power module; includes clothing clip and windscreen only; 55" (1.4 m) cable terminated with locking 4-pin connector for A-T UniPak® wireless systems AT831cT5 - less power module; includes clothing clip and windscreen only; 55" (1.4 m) cable terminated with TA5F connector for ATW-U101 body-pack wireless system
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Cardioid
Frequency Response: 40-16,000 Hz
Low Frequency Roll Off: 80 Hz, 18 dB/octave
Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
Impedance: 250 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 112 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Switch: Flat, roll-off
Cable: 4.0 m (13.1') long (permanently attached to microphone), 3.2 mm (0.13“) diameter, 2-conductor, shielded cable with TA3F-type connector
Accessories: AT8417 clothing clip; AT8444 guitar adapter; AT8538 remote power module; AT8116 windscreen; protective carrying case
|
Reviews
There are no reviews yet.