Content |
Shure WL-185 Lavalier Condenser Microphone
Models WL183, WL184 and WL185 are lavalier electret condenser mics designed for use
with a wireless body-pack transmitter. Each mic has a 1.2 meter (4 ft.) cable terminated
with a miniature 4-pin mini connector. Included tie clip can be rotated in 90 degree intervals for placement flexibility.
WL185 (Cardioid):
Recommended for general purpose sound reinforcement applications requiring good rejection of ambient noise.
Use of windscreen highly recommended. Pickup angle: 130 degrees.
Type
Condenser (electret bias)
Frequency Response
50 to 17,000 Hz
Output Impedance
1800 ohms
Sensitivity (1 Pa = 94 dB SPL)
WL183: -40.0 dBV/Pa
WL184: -44.5 dBV/Pa
WL185: -45.5 dBV/Pa
Maximum Sound Pressure Level
WL183: 125.0 dB SPL
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
Output Noise (A-weighted)
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
Dynamic Range
102.5 dB
Polarity
Positive pressure on diaphragm produces positive voltage on pins 3 and 4 relative to pin 1.
Power Requirements
Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) provided at microphone connector pin 2 relative to pin 1 of a Shure wireless microphone transmitter.
|
All models include foam windscreen, swiveling lapel clip, dual tie clip, pin mount, magnet mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Unidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
High Boost equalization caps included for optimal clarity and response
Provides a 10 dB boost centered at 12 kHz
Used in applications that require a chest-worn microphone
Black and white models available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens and carry case
requency response: 20-20,000 Hz
Low visibility with a variety of options for mounting
Low handling noise
Legendary Shure quality, ruggedness, and reliability
|
Shure SLX14 Instrument Wireless System Features:
SLX4 Wireless Receiver:
Automatic Frequency Selection
Automatic Transmitter Setup
960 Selectable frequencies across 24MHz bandwidth
Detachable 1/4 wave antennas
Microprocessor-controlled diversity
RF presence LED
5-segment audio meter
Multi-function, backlit LCD
Low battery indicator
Frequency and power lockout
Rugged metal chassis
Volume control on rear of unit
1/2 rack design
Furnished rack hardware
Non-slip bumpers for use out of rack
XLR and 1/4" outputs
SLX1 Bodypack Transmitter
Automatic Transmitter Setup
Backlit LCD with timeout feature
Frequency and power lockout
3-segment battery fuel gauge
2 AA batteries (included) provide 8 hours of continuous use
518 - 782 MHz operating range
Shure SLX14 Instrument Wireless System Specifications:
SLX4 Wireless Receiver:
Audio Output Level (ref. ± 38kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): —13dBV; 1/4" connector (into 3000 Ohm load): —2dBV
Output Impedance: XLR connector: 200 Ohms; 1/4" connector: 1kohms
XLR output: Impedance balanced; Pin 1: Ground; Pin 2: (+); Pin 3: (-)
Sensitivity: —105 dBm for 12 dB SINAD, typical
Image Rejection: >70 dB, typical
Power Requirements: 12—18 Vdc at 150 mA, supplied by external power supply
Operating Range Under Typical Conditions: 300 ft. (100m)
Note: Actual range depends on RF signal absorption, reflection, and interference
Audio Frequency Response (+/— 2 dB): Minimum: 45 Hz: Maximum: 15 kHz
Note: Overall system frequency depends on microphone element.
Total Harmonic Distortion (ref. +/— 38 kHz deviation, 1 kHz tone): 0.5%, typical
Dynamic Range: >100 dB A-weighted
Operating Temperature Range: —18 degree C (0 degree F) to +50 degree C (+122 degree F)
Note: battery characteristics may limit this range
Dimensions (H x W x D): 1.65 x 7.76 x 5.28 in., (42 x 197 x 134 mm)
Weight: 1 lb. 13 oz. (816 g )
Housing: Galvanized steel
Transmitter Audio Polarity: Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with
respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
Logic Connections: Pin 1: Logic output, Transmitter Mute Status. Mute=low (0 V). Sinks up to 100 mA. Absolute maximum -0.7 to 5.5V DC; Pin 2: Logic ground; Pin 3: Logic output, Battery Status. Good=low (0 V). Sinks up to 100 mA; Absolute maximum -0.7 to 5.5V DC
SLX1 Bodypack Transmitter
Audio Input Level: -10 dBV maximum at mic gain position, +10 dBV maximum at 0 dB gain position, +20 dBV maximum at -10 dB gain position
Gain Adjustment Range: 30dB
Input Impedance: 1 Mohms
RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations
Dimensions (H x W x D): 4.25 x 2.50 x 0.75 in. (108 x 64 x 19 mmD)
Weight: 81 grams (3 oz.) without batteries
Housing: Molded ABS case
Power Requirements: 2 "AA" size alkaline or rechargeable batteries
Battery Life: >8 hours (alkaline)
|
All models include foam windscreens, swiveling lapel clip, dual tie clip, magnet mount, and mini mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Omnidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
Two sensitivities available:
--Standard: -40 dBV/Pa (for speech applications)
--Reduced: -50 dBV/Pa (10 dB more headroom for theater applications)
Interchangeable equalization caps for optimal clarity and response:
--Silver mesh cap provides a 4 dB boost in the 8-18 kHz range - typically used in applications that require a microphone to be head-mounted
--Gold mesh cap provides a 10 dB boost centered at 12 kHz - typically used in applications that require a chest-worn microphone
Black, beige, and white models are available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens
Frequency response: 20-20,000 Hz
| Subminiature lavalier design; ideal size for theater, television, broadcasting, video, film, and sound reinforcement
Small, inconspicuous mounting hardware
Full, clear sound comparable to larger microphones
Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
Controlled low-frequency rolloff reduces low-frequency clothing and room noise
Low distortion, wide dynamic range
Uniform omnidirectional polar pattern
Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
Wide-range phantom powering (SM93) accepts all commonly used voltages
Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz
Response Curve Image Small SM93 WL93 View Larger
Polar Pattern
Omnidirectional, uniform with frequency
Output Impedance
3000 ohms
Output Level (1 Pascal = 94 dB SPL)
Open Circuit Voltage: -38 dBV/Pa (13 mV)
Output Clipping Level (at 1,000 Hz)
0.25 V at 120 dB
Total Harmonic Distortion
Less than 1% at 120 dB
Maximum SPL
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL)
18 dB typical, A-weighted
Signal-to-Noise Ratio
76 dB at 94 dB SPL (IEC 651)
Polarity
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
*Produces positive voltage at pin 2 of Shure wireless receiver three-pin connector
Recommended Operating Voltage
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
Current Drain
40 microA typical
Environmental Conditions
Operating Temperatures: -18 to 57 degrees C (0 to 135 degrees F)
Storage Temperatures: -29 to 74 degrees C (-20 to 165 degrees F)
Cable
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type TA4F (WL93T: Tan 1.27 m [4.17 ft])
Case
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Net Weight
Microphone: 16 g (0.57 oz) |
The Electro-Voice ULM18 Unidirectional Lavalier Microphone provides hands-free speech and vocal operation with the Electro-Voice R300 wireless microphone system. The ULM18 connects to the BP300 beltpack transmitter.
Product Highlights - For R300 Wireless System
- Compatible with BP300 Beltpack
- Unidirectional Polar Pattern
|
Reviews
There are no reviews yet.