Content |
The Sontronics Apollo is an active stereo ribbon mic based on the Sigma, another ribbon microphone from Sontronics.
The Apolloʼs dual transducers are in a fixed XY configuration, and since both ribbons offer a bi-directional polar response, the Apollo functions as a Blumlein mic. The ribbons are independent of each other, allowing for use of the Apollo as a mono ribbon microphone.
One of the primary benefits of stereo microphones is that they eliminate many of the difficulties associated with accurate placement for stereo recordings. The Apollo is no exception, though only for Blumlein setups. Since both ribbons are fixed in their positions, other stereo configurations such as ORTF are not an option.
According to one reviewer, the Apollo does not perfectly address another issue inherent to stereo setups: gain matching.
Specifications
Frequency Response - BlumleinClick Graph to Compare!
Apollo Blumlein Frequency Response Chart
Pickup Patterns Pads & Filters
Blumlein (18 mV/Pa; 20 - 20,000 Hz)
Ribbon Construction Impedance SPL/Noise
If desired, only a single ribbon can be used 150 Ohms (Low) Self-noise: 12.0 dB(A)
Weight Length Max Diameter Interface(s)
n/a n/a n/a
3-pin XLR male (2)
Power Specifications
Requires phantom power
Phantom voltage: 48v
|
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Cardioid | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohms | 18 mV/Pa | Rated impedance | 50 ohms | Rated load impedance | 1000 ohms | Equivalent SPL CCIR 468-3 | 21 dB | Equivalent SPL DIN/IEC 651 | 10 dB-A | S/N ratio CCIR 468-3 | 73 dB | S/N ratio DIN/IEC 651 | 84 dB | Maximum SPL for THD 0.5% | 140 dB | Maximum output voltage | 13 dBu | Dynamic range of the microphone amplifier DIN/IEC 651 | 130 dB | Supply voltage | 48 V ± 4 V | Current consumption | 3 mA | Matching connectors | XLR 3F | Weight | 480 g | Diameter | 49 mm | Length | 175 mm |
|
Variable large diaphragm microphone | Pressure-gradient transducer with double membrane capsule | The studio microphone classic | Three directional characteristics: omni, cardioid, figure-8 | Switchable low frequency roll-off | Switchable 10 dB pre-attenuation |
Ideal as main and as support microphone in the most differing recording situations
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Omnidirectional, cardioid, figure-8 plus | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 20/28/22 mV/Pa1) | Rated impedance | 200 ohms | Rated load impedance | 1 kohms | Equivalent noise level, CCIR2) | 26/23/25 dB1) | Equivalent noise level, A-weighted2) | 15/12/14 dB-A1) | Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) | 68/71/69 dB1) | Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) | 79/82/80 dB1) | Maximum SPL for THD 0.5%3) | 117 dB (cardioid) | Maximum SPL for THD 0.5% with preattenuation3) | 127 dB | Maximum output voltage | 390 mV | Dynamic range of the microphone amplifier (A-weighted) | 105 dB | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | Current consumption (P48, IEC 61938) | 0.8 mA | Matching connectors | XLR3F | Weight | 500 g | Diameter | 56 mm | Length | 200 mm |
| |
NT1000 - ?Pure Performance? Ultra Versatile 1? Studio Condenser Microphone.
With its ultra low 6 dBA self-noise and transformer less SMT circuitry, the
R?DE NT1000 exhibits exceptional performance when recording both vocals
and instruments in the studio.
Voiced for ?application versatility?, the NT1000 has been hailed by many as the
ultimate drum over-head and grand piano mic selection. The NT1000 is also
equally at home as a first call vocal mic. With its Australian made 1? HF-2 capsule
incorporating internal shock mounting, the NT1000 boasts a 134 dB dynamic range,
and 140 dBA SPL capabilities and a 20 Hz ? 20 kHz frequency response.
Built of a heavy-duty cast metal satin nickel body, the NT1000 incorporates a
high-strength, heat-treated mesh head, and comes supplied in a zip pouch with a
stand mount.
SPECIFICATIONS:
Acoustic principle:
Externally polarised 1? (25mm) pressure-gradient condenser
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651:
> 88dB (A-weighted, per IEC268-15)
Equvalent noise:
6dB SPL (A-weighted per IEC268-15) +/-1dB
Maximum spl:
> 140dB SPL (@ 1kHz, 1% THD into 1k( load)
Sensitivity:
-36dB re 1V/Pa (16mV @ 94dB SPL) +/-1dB
Dynamic range din iec 651: > 134dB (A-weighted, per IEC268-15)
Power supply voltage: P48 (35V - 53V)
Current consumption: 6mA
Weight without battery: 682 gm
Weight with battery: 882 gm
|
The AVANTONE CK-6 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET mics…but at a fraction of their cost!
The rugged CK-6 microphone body and capsule assembly are precision machined of Brass. Aesthetically the compact body features an elegant Metallic Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.
This Transformerless CLASS A FET Microphone w/ 32mm gold sputtered thin Mylar capsule is designed with circuitry that will yield pleasing professional results comparable to much more expensive designs. It also features -10 dB pad & 80 Hz LF roll off switches for varied recording situations.
The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.
Applications
Studio vocals, acoustic guitar, mandolin, drum overheads, piano, etc…
Specifications
Type: True Transformerless Condenser
Polar Pattern: Cardioid
Frequency Response: 35-20,000 Hz +/- 3.5dB
Output Impedance: |
K2 - ?It cant be done?? Precision Variable Pattern Dual 1? Condenser Valve Microphone.
The R?DE K2 is the result of designing and building 1000?s of valve microphones. The
K2?s HF-1 capsule is the pinnacle of transducer technology. The sound quality combines
modern high-end specifications with the character and subtleties of the legendary 50?s mics.
Infinitely variable control of the K2?s polar patterns provides the freedom and flexibility to
excel in any recording situation. The K2 is another example of R?DE?s commitment to
building quality studio microphones to meet the exacting standards demanded by today?s
professionals.At the 2004 Frankfurt Music Messa, 56 of the most prestgious music industry
magazines voted the K2 the ?Best Studio Microphone of 2004?.
SPECIFICATIONS:
Features:
? New large capsule with gold sputtered diaphragm. ? Ultra low noise.
? Wide dynamic range. ? Class ?A? valve circuitry. ? Hand-selected and
graded 6922 twin-triode valve. ? Dedicated Power Supply. ? High strength
welded and heat-treated steel mesh head. ? Durable satin nickel finish.
? Internal capsule shock mounting. ? High level of RF rejection. ? Supplied
complete with SM2 Shock Mount and RC2 Custom Carry Case.
? Continuously variable polar patterns. From omni, through cardiod to
figure 8, controlled at the power supply.
Operation power:
The K2 is designed to operate from a dedicated power supply (110 - 120 V/220 - 240 V, 50/60 Hz)
Acoustic principle: Externally polarized 25 mm(1?) condenser.
Directional pattern:
Continuously variable multi pattern -Omni, through Cardioid to figure 8.
Frequency range: 20 Hz - 20 kHz
Output impedance:
Valve impedence converter with bipolar output buffer.
Signal noise ratio din iec 651:
> 81 dB (1kHz relative to 1 Pa; per IEC651,IEC268-15).
Equvalent noise: 10 dBA SPL (per IEC651, IEC268-15).
Maximum spl: 162 dB (@ 1% THD into 1k).
Sensitivity:
-36 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB.
Power supply voltage:
Dedicated Power Supply(110 - 120 V/220 - 240 V, 50/60 Hz).
Weight: 815 gms
Dimensions width: 208.5 mm
Dimensions depth: 55 mm
Dimensions height: 55 mm
Maximum output voltage: > +30 dBu (@ 1% THD into 1 k).
|
Reviews
There are no reviews yet.