| Content | With omni-directional, cardioid and figure-of-eight patterns, as well as a 10dB cut/boost function, Sontronics ORPHEUS is the perfect choice for practically any studio or live application.
Its low self-noise and unmistakable presence allow you to record the subtlest of instruments or voices without the need
to edit afterwards.
The highly sensitive 35mm dual-diaphragm capsule is suspended in its own special mount, almost floating in the large, spherical basket. ORPHEUS's body is cast from zinc alloy, which gives a very low resonance, helping to keep the signal tight and accurate.
Sontronics ORPHEUS is supplied in a luxury, velvet-lined wooden case and really does sound as good as it looks. When used as a room mic or for drum overheads, either on its own or in a pair, ORPHEUS will totally blow your mind!
Technical Specifications
There is rather less technical spec provided with these mics than I'd like to see for microphones in this price range. Specifically, there's no response plot, so I couldn't see where the presence peak, (which my ears told me was definitely there), was located. Both mics have a quoted 20Hz-20kHz frequency response, but without saying how many decibels down the response is at the extremes, so the numbers are pretty meaningless.
Both mics have a 20mV/Pa sensitivity, which is in the same ball park as most other large-diaphragm capacitor mics, and the solid-state Orpheus has a 2dB better EIN figure than the tube-based Helios, which is quoted as 18dBA. While these figures are perfectly acceptable for most studio tasks (and as good as or better than most Chinese-built mics), they aren't as good as some of the newer designs from the more mainstream mic companies. For example, a modern-day Neumann U87 comes in at around 12dB EIN, and many of Rode's mics, which use a new generation of surface-mount circuitry, manage an astonishingly low 7dB EIN or better.
The maximum SPL handling is also a little lower than average at 125dB at 1kHz for 0.5 percent distortion. Most mics manage 135dB or thereabouts, with the most tolerant getting up above 140dB. Putting this into perspective, it isn't going to affect vocal recording, and that's mainly where this mic is aimed, but close-miking brass instruments or loud percussion could throw up problems. If you're using this as a conventional studio vocal mic or for instruments like acoustic guitar, then both the noise figure and the maximum SPL handling are absolutely no problem. |
K2 - ?It cant be done?? Precision Variable Pattern Dual 1? Condenser Valve Microphone.
The R?DE K2 is the result of designing and building 1000?s of valve microphones. The
K2?s HF-1 capsule is the pinnacle of transducer technology. The sound quality combines
modern high-end specifications with the character and subtleties of the legendary 50?s mics.
Infinitely variable control of the K2?s polar patterns provides the freedom and flexibility to
excel in any recording situation. The K2 is another example of R?DE?s commitment to
building quality studio microphones to meet the exacting standards demanded by today?s
professionals.At the 2004 Frankfurt Music Messa, 56 of the most prestgious music industry
magazines voted the K2 the ?Best Studio Microphone of 2004?.
SPECIFICATIONS:
Features:
? New large capsule with gold sputtered diaphragm. ? Ultra low noise.
? Wide dynamic range. ? Class ?A? valve circuitry. ? Hand-selected and
graded 6922 twin-triode valve. ? Dedicated Power Supply. ? High strength
welded and heat-treated steel mesh head. ? Durable satin nickel finish.
? Internal capsule shock mounting. ? High level of RF rejection. ? Supplied
complete with SM2 Shock Mount and RC2 Custom Carry Case.
? Continuously variable polar patterns. From omni, through cardiod to
figure 8, controlled at the power supply.
Operation power:
The K2 is designed to operate from a dedicated power supply (110 - 120 V/220 - 240 V, 50/60 Hz)
Acoustic principle: Externally polarized 25 mm(1?) condenser.
Directional pattern:
Continuously variable multi pattern -Omni, through Cardioid to figure 8.
Frequency range: 20 Hz - 20 kHz
Output impedance:
Valve impedence converter with bipolar output buffer.
Signal noise ratio din iec 651:
> 81 dB (1kHz relative to 1 Pa; per IEC651,IEC268-15).
Equvalent noise: 10 dBA SPL (per IEC651, IEC268-15).
Maximum spl: 162 dB (@ 1% THD into 1k).
Sensitivity:
-36 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB.
Power supply voltage:
Dedicated Power Supply(110 - 120 V/220 - 240 V, 50/60 Hz).
Weight: 815 gms
Dimensions width: 208.5 mm
Dimensions depth: 55 mm
Dimensions height: 55 mm
Maximum output voltage: > +30 dBu (@ 1% THD into 1 k).
| Behringer C-1 Studio Condenser Microphone
Behringer C-1 Studio Condenser Microphone
The C-1 Studio Condenser Microphone from Behringer offers a cardioid pickup pattern for maximum sound source separation and feedback rejection. This low noise microphone is suitable for a wide range of recording scenarios, including project, professional, and home studio applications. There is a pressure gradient transducer and a shock-mounted large diaphragm capsule for open, transparent sound with high-quality transient response. It is constructed of a die-cast metal body for durability and features an LED light to indicate when the microphone is receiving phantom power. The C-1 includes a swivel mount and custom case.
- Professional large-diaphragm condenser microphone for unsurpassed audio quality
- Ideal as main and support microphone for studio and live applications
- Exceptionally flat frequency response and ultra-high sound resolution
- Cardioid pickup pattern for outstanding sound source separation and feedback rejection
- Ultra low-noise transformerless FET input circuitry
- LED indicates phantom power operation
- Gold-plated 3-pin XLR output connector for perfect signal transmission
- Ultra-rugged construction with die-cast body
- Swivel stand mount and carrying case included
| Operating Principle |
Pressure Gradient |
| Capsule |
Condenser |
| Diaphragm |
0.63" / 16.0 mm |
| Polar Pattern |
Cardioid |
Performance
| Frequency Range |
40 Hz to 20 kHz |
| Maximum SPL |
136 dB SPL |
| Impedance |
100 Ohms |
| Load Impedance |
1000 Ohms |
| Sensitivity |
-33 dB |
| THD |
1% |
Connectivity
| Output Connectors (Analog) |
1 x XLR 3-Pin |
Power
| Operating Voltage |
36 to 52 V |
| Operating Current Consumption |
2.5 µA |
Physical
0.93 lb / 0.42 kg
| Dimensions |
ø: 2.13 x L: 7.09" / ø: 54 x L: 180 mm |
| Weight |
|
|
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 13 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent noise level, CCIR1) | 23 dB | | Equivalent noise level, A-weighted1) | 12 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 71 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 82 dB | | Maximum SPL for THD | 110 dB | | Maximum SPL for THD | 129 dB | | Maximum output voltage for THD | -1 dBu | | Dyn. range of the mic. amplifier /A-weighted, 0.5 %2)) | 98 dB | | Dyn. range of the mic. amplifier /A-weighted, 5 %2)) | 117 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3.2 mA | | Matching connector | XLR 3F | | Weight | 825 g | | Diameter | 78 mm | | Length | 165 mm |
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal |
|
|
| Large diaphragm cardioid microphone | | Pressure gradient transducer with with one-diaphragm capsule | | Transformerless circuitry | | Extremely low noise: 7 dB-A | | Includes swivel mount | | Straightforward handling for homerecording and professional studios | |
High-quality professional equipment for limited budgets
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 23 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR1) | 17.5 dB | | Equivalent noise level, A-weighted1) | 7 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 76.5 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 87 dB | | Maximum SPL for THD 0.5%2) | 138 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier (A-weighted) | 131 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3 mA | | Matching connector | XLR3F | | Weight | approx. 450 g | | Diameter | 60 mm | | Length | 132 mm |
|
| The C 414 B/XLS has been carefully designed to maintain the legendary sonic character of the C 414 family while integrating new features and performance enhancements made possible by new technology. The C 414B/XLS is designed to deliver accurate pickup of all acoustic instruments and voices.
The microphone's 5 pickup patterns are easily selectable via an electronic switch with LED indication and offer the selection of omnidirectional, cardioid, wide cardioid, hypercardioid and figure-eight patterns.
The pickup pattern selector switch utilizes a dual-color LED indicator that provides visual indication of the pattern selected and also changes from green to red to indicate if the microphone's output electronics are being overloaded. The pattern selector can also be used to "lock" the microphone's switch settings by pressing and holding it for 3 seconds.
On the rear of the microphone, an electronic switch allows the selection of -6 dB, -12 dB and -18 dB pre-attenuation levels which are accomplished by changing the polarization voltage to the capsule. The C 414 B/XLS has switchable bass cut filters of 12 dB-per-octave at 40 Hz and 80 Hz, and a 6-dB-per-octave filter at 160 Hz for control of proximity effect. On-axis sensitivity for all patterns is 23 mV/Pa and its self-noise is an extremely low 6 dB-A.
The C 414 B/XLS has a transformerless output and all-metal chassis, making it immune to electrical interference and RF from digital equipment, video monitors and wireless systems. It comes complete in an all-metal road case with the AKG H-85 shock mount, a PF80 external two-stage pop filter, a W414X external windscreen and an individually-measured chart showing the response curve of the microphone. It is also available in factory-matched stereo pairs packaged with a H50 stereo bar instead of the external pop filter.
The C 414B/XLS is built in Vienna, Austria and comes with a three-year limited parts and labor warranty.
Features
High sensitivity and extremely low self noise
Five switchable polar patterns for placement and application flexibility
Two-color LEDs provide quick visual indication of selected polar pattern and output overload
Elastic capsule suspension greatly minimizes structurally-transmitted noise from chassis vibration
H 85 professional shock mount/stand adapter, PF 80 external pop filter and W 414 X external windscreen
High sound pressure level capability and wide dynamic range
Completely immune to electrostatic and electro-magnetic interference from digital gear, computer monitors, etc. thanks to solid metal housing and transformerless output stage
Three switchable bass cut filters and three pre-attenuation pads with LEDs for quick visual indication
All switchable components operate in low impedance circuits for ultra-high relability even in extremely humid conditions
Optional R 414 remote control unit (available by the end of 2004) offers full control of all switchable parameters via standard microphone cable and 3-pin XLR-type connectors
Specifications
Type: 1" large diaphragm pressure gradient microphone
Polar Patterns: Omnidirectional, wide cardioid, cardioid, hypercardioid, figure eight
Frequency Range: 20 to 20,000 Hz
Sensitivity: 23 mV/Pa (-33 dBV) +/-0.5 dB
Max. SPL: 140/146/152/158 dB SPL (at 0/-6/-12/-18 dB)
Preattenuation Pad: -6, -12,-18 dB, switchable
Bass Cut Filter Scope: 12 dB/octave at 40 Hz and 80 Hz; 6 dB/octave at 160 Hz
Power Requirements: 48 V phantom power to DIN/IEC
Connector: 3-pin XLR
Dimensions: 2" x 1.5" x 6.3“
Net Weight: 10.6 oz
Shipping Weight: 5 lbs (2.27 kg) |
Reviews
There are no reviews yet.