| Content | The Sontronics STC-10 is a cardioid pencil condenser microphone that is based on the companyʼs STC-1.
While the STC-1 accepts alternate capsules with different polar patterns from Sontronics, the company makes no mention of compatibility with the STC-10. This leads us to believe that the capsule is not interchangeable, which likely allows the microphone to be priced lower than its predecessor.
The STC-10 features switches for a pad (-10 dB) and low-cut filter (at 75 Hz) on its front.
According to Sontronics, the STC-10 is designed to sound similar to the STC-1, at a lower cost. The company does not go into specifics, but some examples of areas they were able to cut costs were in accessories and expandability. The STC-10 ships with a mic clip and windscreen, though a shockmount and padded case are available for purchase separately.
Specifications
Pickup Patterns Pads & Filters
Cardioid (11 mV/Pa; 30 Hz - 20,000 Hz)
Pad: -10 dB (Via Switch)
Filter: Low cut at 75 Hz (Via Switch)
Capsule Dimensions Impedance SPL/Noise
Diameter n/a
200 Ohms (Low) Max SPL: 130 dB
Self-noise: 18.0 dB(A)
Weight Length Max Diameter Interface(s)
n/a n/a n/a
3-pin XLR male (1)
Power Specifications
Requires phantom power
Phantom voltage: 48v |
The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern: Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
|
The ME 66 is a shot gun microphone head designed for use with the K6 and K6P powering modules. It is especially suitable for reporting, film and broadcast location applications and for picking up quiet signals in noisy or acoustically live environments as it discriminates against sound not emanating from the main pick-up direction. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : super-cardioid/lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm ( K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 221 mm
Weight : 65 g
|
The ME 67 is a long gun microphone head designed for use with the K6 and K6P powering modules. A highly directional microphone, it can be used where the microphone must be placed at a distance from the sound source. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm (K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 343 mm
Weight : 100 g
|
Weighing only 18 grams (0.6 oz.), this ultra-light condenser pickup is ideal for acoustic guitar, mandolin, violin, and most other stringed instruments. The C 411 will give a clear and uncolored sound without changing the balance of the instrument. Attaching the C 411 on or near the bridge or anywhere else on the instrument is easy with the included non-marring, reusable, solventfree adhesive compound.
C 411 PP: For hardwire applications, with standard XLR connector for phantom powering. |
The super-cardioid e 614 is a permantly polarized condenser microphone
designed for demanding applications which require a wide frequency response,
high SPL, fast transient response and a compact design. With its frequency
response of 40 Hz to 20 kHz, the e 614 is able to capture the full sound of the
instrument, while its super-cardioid pick-up pattern isolates the microphone
from other on-stage signals.
An excellent microphone for percussion instruments, the e 614 is also an ideal
choice for woodwind and string instruments. Its excellent acoustic properties
also make it a valuable tool for home recording.
Features
Rugged design Effective rejection of incidental rear noise Excellent directivity
across the whole frequency range Full, natural sound High maximum sound
pressure level
Wide frequency response
Delivery Includes
Microphone pouch
Microphone clip MZQ 100
Technical Data
Frequency response 40 Hz ... 20 kHz
Transducer principle permanently polarized condenser
Pick-up pattern supercardioid
Sensitivity in free field, no load (1kHz) 3 mV/Pa = - 50dB (0 dB = 1 V/Pa)
Nominal impedance 50 Ohm
Min. terminating impedance 1 kOhm
Maximum sound pressure level (passiv) 139 dB/SPL
Equivalent noise level 24 dB(A)
Equivalent noise level weighted as per CCIR 468-3 35 dB
Dimensions ? 20mm, L = 100mm
Weight w/o cable 93 g
|
Reviews
There are no reviews yet.