Content |
PM Series ? PM-15 2-Way, 15“ High Power System |
Characteristics |
|
Multi-angled unit, designed for Sound Reinforcement or floor Monitor. |
|
Multi-use Mid-High Constant Directivity, rotateable 90x45 degrees Horn. |
|
Active driver "Power Guard" protection without any effective loss. |
|
High Sound Pressure Level, (134dB Peak@1m, pink noise with a 6dB crest-factor). |
|
Rotateable Horn and optimised cabinet architecture for monitor and small P.A. uses. |
|
Two-way passive 8 Ohm design to be used with a single power Amp channel per cabinet to obtain an easy assembly and low cost. |
|
Two way bi-amp active operation via external toggle switch. |
|
Passive filter which optimises the voice critical zone response. |
|
Double input NL-4 Neutrik connector permitting parallel bridging. |
|
Steel front grille with acoustic foam, easily removable, held in place with powerful Neodymium magnets. |
|
Suspension Tracks on top and bottom, standard pole cup and thread inserts. |
|
The specific electronic controller guarantees: linear performance, powerful bass response, and reliability. |
Applications |
|
Touring, installed P.A., theatres, multi-purpose rooms, etc. |
|
High performance monitoring |
|
When used together with the series' Sub-woofer PMS-15, the system becomes a performing set-up for many dance applications. |
Specifications and Characteristics |
Frequency Response (Hz) 1 |
-3dB 56Hz - 18KHz |
Frequency Range (Hz) 1 |
±10dB 44Hz - 20KHz |
Nominal Impedance |
Full Range 8 Ohm Bi-amp Low - 8 Ohm Bi-amp High - 8 Ohm |
Full Range Power Rating (RMS) 2 |
700W AES/ 2800W Peak |
Bi-amp Power Ratings (RMS) 2 |
Low 700W AES / 2800W Peak |
Horizontal Coverage |
(-6dB) 90? |
Vertical Coverage |
(-6dB) 40? |
Sensitivity (dB/1w@1m) |
Full Range 98dB Bi-amp Low 98dB / High 112dB |
SPL Max. Peak (dB SPL@1m) 3 |
Full Range 134dB SPL Bi-amp Low 134dB / High 137dB |
Connectors |
2 Neutrik NL-4 Connectors on steel plate |
Recommended Signal Processor |
RAM Audio LMS-244 Digital Processor
|
Recommended Power Amp |
Full range 800W - 1200W RMS@8 Ohm Bi-amp Low 800W - 1200W RMS@8 Ohm Bi-amp High 100W - 200W RMS@8 Ohm |
Recommended Sub-woofer |
Space PMS-15 or Space ARS-215 |
Enclosure and Installation |
Enclosure |
Vertical, multi-angle 18mm Baltic cross-ply construction, tongue and groove assembly throughout. Bi-component epoxy finish. |
Protection Grille |
1.5mm laminated steel with textured epoxy finish. |
Handle |
On top of the cabinet |
Dimensions (HxWxD) |
700 x 424 x 384 mm 27.5 x 16.7 x 15.1 inches |
Net Weight |
34Kg (74.9 pounds) |
Rigging |
Integrated track rigging system on top and bottom. M-8 Inserts for bolt assembly. |
|
Notes |
|
1 Specifications in half space 2 With filtered Pink Noise 6dB crest-factor 3 Calculated from the Sensitivity and Power Data | |
Description:
The SX18 is a switchable 3 way active, 2 way passive, arrayable loudspeaker. Designed to be used as the main enclosure for small to mid-sized venues or as a supplemental cabinet for large scale sound reinforcement, this enclosure provides high sound pressure levels in a small, lightweight package. Adamson?s Proprietary Kevlar drivers and internal crossovers are employed throughout the SX18 enclosure and its integral fly hardware makes installation of the product fast and effective. Moving the SX18 is easy and efficient with the supplied dolly board. A flexible, high powered enclosure, the SX18 is suited for a wide variety of applications.
Applications:
Live Concert Reproduction
Side Fill Monitoring
Near Field Applications
Theatres
Houses of worship
Dance Clubs
Features:
Kevlar 18" bass and 10" midrange Drivers
1.5" High Frequency Compression Driver
2-Way Bi-Amp/3-Way Tri-amp Operation (selectable)
Adamson Acoustic Waveguide
Integrated Fly Points
Supplied Dolly Board
Durable, Dual Component Finish
Honeycomb Punched, Steel Grille
Roadworthy Construction
Weight: 67 kg
|
Club Series V
Gigging bands, mobile DJs and houses of worship have helped make the first four generations of Yamaha Club Series Speakers incredibly popular. The refinements of generation V continue this success story: larger enclosures for improved low-frequency performance, improved drivers for higher power handling, redesigned crossovers, stronger grilles, and dual Speakon® and ¼" connectors. Once again, with professional features, excellent sonic performance and great value, Club Series loudspeakers deliver premium quality night after night.
Yamaha has a long history of both making and reproducing music. The Club series V loudspeakers represent the latest in our continuing effort to provide the professional features and sound quality you've come to expect and deserve.
Built in the United States, these loudspeakers are designed to provide years of service. high power handling and excellent response have made Club Series loudspeakers the perfect choice for more than 16 years. Whether playing in a band, DJing, orupgrading the sound system at your church or school, with an expanded lineup of over twenty models to choose from, you're sure to find the right loudspeaker. Have a look at what goes into their construction -- Cabinets are constructed of high quality particleboard, chosen for its high strength and elasticity, consistent void free makeup and light weight. Another great benefit of this material is its environmental friendliness. Made from southern yellow pine, this material is both abundant and quickly renewable. Accurate CNC routing machines are used to cut every part, assuring consistency with tolerances of one ten thousandth of an inch. Skilled technicians assemble each cabinet by hand, rejecting any defects. Whether covered in durable carpet or the elastomeric spray coating, heavy steel handles and sturdy pole sockets make moving and positioning easy.
The drivers, or speakers in these cabinets, are custom made my Eminence Speaker Corporation® to Yamaha's exacting tolerances. Woofers share design features like high strength curvilinear cones and Dupont KaptonTM voice coil formers. Oxygen-free copper voice coils and oversize strontium ferrite magnets are also used to provide high power handling and long life. The 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex and help dissipate heat. The compression driver that generates the high frequency sound uses a pure titanium diaphragm. This 2" dome is one of the largest in its class, allowing for very high output and low distortion, without the aid of cooling fluids. It's mated to a 90° x 40° custom designed CD (constant directivity) horn with excellent dispersion and response.
Crossover networks that divide the signal going to the woofer and compression driver are constructed with oversized coils, high voltage capacitors, and power resistors designed to provide the best possible sound quality and minimize loss. Overload protection is also included to protect the components.
Connections on these loudspeakers are dual Neutrik Speakon® ¼ jacks for the highest possible strength and current capacity. Two of each connector makes it easy to "daisy chain," or add speakers.
Club V loudspeakers with the C prefix are coated with a heavy-duty elastomeric spray coating. Designed as an installation alternative to the carpeted S versions, they can easily fit any decor. The finish is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.
C215V
Two 15" cast frame woofers
2000-watt peak power handling
90 x 45 degree CD horn
Perfect where high sound pressure levels are required
Features:
- Tough, paintable exterior coating
- Dual cast-frame 15" drivers
- Frequency response: (-10dB) 42Hz - 16kHz
- 1,000W program handling, 2,000W peak
- Sensitivity: 99dB
- 20“W x 46“H x 24“D
- 101 lbs.
| Woofer | Tweeter
(diaphragm) | Freq
Resp
(-10dB) | Power
Handling
(noise 1 /
program/peak) | Sen-
sitivity | Max.
SPL 3 | Dims.
(WxHxD) 2 | Wt. 2
(lbs) |
15" (2) | 2" titanium | 42Hz-
16kHz | 500/1000/2000 | 99dB | 132dB | 20x46x24 | 101.0 |
|
|
* 90° x 50° Coverage, rotatable for use in either vertical or horizontal orientation.
* CMCD™ Cone Midrange Compression Driver™ provides low midrange distortion, increased sensitivity, extended bandwidth and improved phase coherency.
* PT™ Progressive Transition™ Waveguide for excellent pattern control with low distortion.
* Bi-Amp/Tri-Amp Switchable
* Optional planar array frame kit PAF-2K for 3-wide array with ASB6128V subwoofer center. (See AE Series Array Guide).
* For fixed installation applications such as performing arts facilities, theatrical sound design, auditoriums, houses of worship, live nightclubs, dance-clubs/discotheques, sports facilities and themed entertainment venues.
Frequency Range : 38 Hz - 19 kHz (-10 dB)
Frequency Response : 45 Hz - 17 kHz ( ± 3 dB)
Coverage Pattern : 90°x 50°, rotatable waveguide
Directivity Factor (Q) : 10
Directivity Index (DI) : 10 dB
Crossover Modes : Tri-amp / Bi-amp switchable
Passive Crossover Slopes : MF/HF Section in Bi-amp mode: 4th order (24 dB/oct) Linkwitz-Riley HP & LP, 2.1 kHz
Transducer Power Rating (AES) : LF: 1000 W (4000 W peak), 2 hrs
600 W (2400 W peak), 100 hrs
MF: 350 W (1400 W peak), 100 hrs
HF: 75 W (300 W peak), 2hrs
Long-Term System Power Rating (IEC) : LF: 600 W (2400 W peak), 100 hrs
MF/HF: 350 W (1400 W peak), 100 hrs
Maximum SPL : LF: 125 dB-SPL cont avg
(131 dB peak)
Tri-amp mode:
MF: 133 dB-SPL cont avg
(139 dB peak)
HF: 132 dB-SPL cont avg
(138 dB peak)
Bi-amp mode:
MF/HF: 132 dB-SPL cont avg
(138 dB peak)
System Sensitivity of Passive Sections 6 : MF/HF Section in Bi-amp mode: 108 dB SPL (1W @ 1m)
|
Ειδική έκδοση του AM 7315/95 για χρήση σε
εξωτερικό περιβάλλον και ακραίες καιρικές
συνθήκες με επιπλέον αναβάθμιση 14 σημειων.
Πιστοποίηση IP56 κατά πρότυπο IEC 529.
Παράδοση κατόπιν παραγγελίας.
Frequency Range : 38 Hz - 19 kHz (-10 dB)
Frequency Response : 45 Hz - 17 kHz ( ± 3 dB)
Coverage Pattern : 90°x 50°, rotatable waveguide
Directivity Factor (Q) : 10
Directivity Index (DI) : 10 dB
Crossover Modes : Tri-amp / Bi-amp switchable
Passive Crossover Slopes : MF/HF Section in Bi-amp mode: 4th order (24 dB/oct) Linkwitz-Riley HP & LP, 2.1 kHz
Transducer Power Rating (AES) : LF: 1000 W (4000 W peak), 2 hrs
600 W (2400 W peak), 100 hrs
MF: 350 W (1400 W peak), 100 hrs
HF: 75 W (300 W peak), 2hrs
Long-Term System Power Rating (IEC) : LF: 600 W (2400 W peak), 100 hrs
MF/HF: 350 W (1400 W peak), 100 hrs
Maximum SPL : LF: 125 dB-SPL cont avg
(131 dB peak)
Tri-amp mode:
MF: 133 dB-SPL cont avg
(139 dB peak)
HF: 132 dB-SPL cont avg
(138 dB peak)
Bi-amp mode:
MF/HF: 132 dB-SPL cont avg
(138 dB peak)
System Sensitivity of Passive Sections 6 : MF/HF Section in Bi-amp mode: 108 dB SPL (1W @ 1m)
|
Large (15“) diameter woofer in a compact, lightweight enclosure.
Compact dimensions made possible by mounting the high frequency driver array in a coaxial configuration with the woofer.
Available in black or white and 100V line models
Extended bass frequencies for rich music reproduction.
The world's smallest* enclosure size relative to the diameter of the woofer.
Easy to transport thanks to compact and light enclosures that other speakers of this class cannot offer.
Product Specifications - Enclosure: Sealed type
- Power Handling Capacity: Continuous pink noise: 100 W, Continuous program: 300 W
- Rated Impedance: 8 Ω
- Sensitivity: 98 dB (1 W, 1 m)
- Frequency Response: 70 - 20,000 Hz
- Crossover Frequency: 3 kHz
- Directivity Angle: Horizontal: 90゜, Vertical: 40゜
- Speaker Component: Low frequency: 38 cm (15) cone-type
- Input Terminal: NEUTRIK NL4MP Speakon and M4 screw terminal, distance between barriers: 9 mm (0.35)“
- Operating Temperature: -10℃ to +50℃ (14゜F to 122゜F)
- Finish: Enclosure: Polypropylene, black
- Punched net: Surface-treated steel plate, black
- Dimensions: 451 (W) × 560 (H) × 400 (D) mm (17.76 × 22.05" × 15.75“)“
- Weight: 12 kg (26.46 lb)
|
Reviews
There are no reviews yet.