Content |
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch |
The Soundweb London BLU-160 offers configurable I/O, configurable signal processing and a high bandwidth, fault tolerant digital audio bus.
The BLU-160 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.
This processor features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the distance between devices to over 40km.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-160 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-160 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.
Features - Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Configurable Signal Processing
- Rich Palette of Processing and Logic Objects
- 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from HiQnet London Architect
|
With 12 inputs and 6 outputs and Ethernet control the dbx ZonePro? 1260 and 1261
are the newest members of the ZonePro? family providing a complete suite of signal
processing and control for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 1260/1261 deliver
the highest quality tools available. Even the input and outputs connectors were chosen for
their standard usage and reliability. The ZonePro products offer Euroblock connectors for
balanced signals and RCA connectors for interfacing with consumer equipment often used
in commercial applications; there is also a simple analog input buss that allows inputs to be
sent from one unit to the next for unit and job scalability. The 1260 and 1261 provide every
necessary processing tool, from the input processing like gain control and EQ available on all
inputs to highly sophisticated and specific functions such as selectable paging microphone
processing including Gating, De-Essing, Auto Gain Control, Compression and Feedback
Suppression. The heart of the ZonePro products is the Routing module that provides of course
Primary Source Selection but also Source Ducking for Paging and Priority Override. The outputs
also offer a wealth of processing designed for commercial applications like our patent-pending
AutoWarmth? function that was co-developed with JBL to provide natural low frequency extension
at any signal level. Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay
for system optimization. With the ZonePro? every tool is at your disposal to maximize the response
of your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters. The addition of
Ethernet control means that not only will it work with standard network equipment, but it can also
be accessed from remote dialup locations or from wireless access points.
The ZonePro? 1260 and 1261 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? IEC, UL and CSA Approvals
ZonePro? 1260/1261 Specifications
ANALOG INPUT
Number of Inputs:
12 Total (2) Switchable mic or line, (8) RCA, and (1)
S/PDIF
Connectors:
Euroblock (Line and Mic) RCA (Source)
Type:
Impedance (Euroblock):
> 50kΩ Balanced, >25kΩ Unbalanced, RF Filtered
Impedance (RCA):
>25kΩ Unbalanced, RF Filtered
Max input line level:
+20dBu Mic/Line, +12dBu RCA
CMRR:
> 40dB, typically >55db @ 1kHz
Mic Pre gain:30 to 60dB
Mic EIN:
> 118dB, 22Hz-22kHz, 150Ω Source Impedance
Mic Phantom Power:
15V
ANALOG OUTPUTS
Number of Outputs 6
Connectors: Euroblock
Type:
Electronically balanced, RF filtered
Impedance:
120 ohms balanced, 60ohm unbalanced
Max Output Level: +20dBu
A/D PERFORMANCE
Type:
dbx Type IV? conversion system
Dynamic Range line:
>113 dB, A-weighted, >110 dB unweighted
Type IV dynamic range:
>119 dB, A-weighted, 22kHz BW
>117 dB, A-weighted, 22kHz BW
Sample Rate: 48kHz
D/A PERFORMANCE
Dynamic Range:
112 dB A-weighted, 109dB unweighted
SYSTEM PERFORMANCE
Dynamic Range:
>110 dB A-weighted, >107dB unweighted
THD+N:
0.003% typical at +4dBu, 1kHz, 0dB gain
Frequency Response:
20Hz - 20kHz, +/-0.5dB
Interchannel Crosstalk:
>80dB typical
Crosstalk input to output:
>80dB
Propagation Delay
0.6 msec
POWER REQUIREMENTS
Operating Voltage:
100-240 VAC, 50/60Hz
Power Consumption:
27 Watts
Physical:
Weight:
6.8 lbs.(3.1 kg) Shipping weight 8.8 lbs. (4.0 kg)
Dimensions:
1.75? H x 5.75? D x 19? W |
Full-featured Speaker Processing in a 1U Space
Speaker processing can be a complicated business requiring a substantial array of equipment, but the Yamaha SP2060 offers everything you need in a single rack space. This innovative 24-bit, 96-kHz digital speaker processor delivers excellent sound quality, an impressive variety of processing functions — gain, delay, PEQ, comp, crossover, limiter, and an all-pass filter for phase adjustment — and intuitive programming from Yamaha's DME Designer application running on a personal computer. It has two analog inputs and six analog outputs, plus two AES/EBU format digital inputs for connectivity with a broad range of systems. And if you use Yamaha Installation Series Speakers, all you need to do is select one of the many optimized presets provided for great sound with minimum measurement and setup time. The SP2060 is a compact, portable 1U unit that is ideal for live sound or installations.
Sampling Frequency | Internal Clock | 96kHz | External Clock | Normal Rate | 44.1, 48kHz (±0.1%) | Double Rate | 88.2, 96kHz (±0.1%) | Signal Delay | 761µsec Input to Output, fs = 96kHz | Frequency Response | 20Hz -40kHz (TYP 0dB, MAX +0.5dB, MIN -1.0dB), fs=96kHz, RL=600ohms | Total Harmonic Distortion | 0.007% (+22dBu@1 kHz),
0.05% (+4dBµ@20 Hz - 40kHz)
fs=96kHz, RL=600ohms;
measured with 18dB/octave filter @80kHz | Hum & Noise | TYP -82dBu,
fs=96kHz, RL=600ohms, Rs=150 ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞ dB/octave attenuation. | Dynamic Range | 106dB AD+DA
fs=96kHz, RL=600ohms;
measured with 6dB/octave filter @12.7kHz;
equivalent to a 20kHz filter with ∞dB/octave attenuation. | Crosstalk @1kHz | -80dB INPUT to Output
fs=96kHz, measured with 18dB/octave filter @80kHz | Power Consumption | 30W | Dimensions (W x H x D) | 480 x 44x 360.2mm | Net Weight | 4.2kg |
|
With 6 inputs and 4 outputs the dbx ZonePro? 640 and 641 provide flexible signal routing,
powerful DSP processing and multiple control interfaces for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 640/641 deliver the
highest quality tools available. Even the input and outputs connectors were chosen for their
standard usage and reliability. The ZonePro products offer Euroblock connectors for balanced
signals and RCA connectors for interfacing with consumer equipment often used in commercial
applications; there is also a simple analog input buss that allows inputs to be sent from one
unit to the next for unit and job scalability. The 640 and 641 provide every necessary processing
tool, from the input processing like gain control and EQ available on all inputs to highly sophisticated
and specific functions such as selectable paging microphone processing including Gating,
De-Essing, Auto Gain Control, Compression and Feedback Suppression. The heart of the
ZonePro products is the Routing module that provides of course Primary Source Selection
but also Source Ducking for Paging and Priority Override. The outputs also offer a wealth of
processing designed for commercial applications like our patent-pending AutoWarmth? function
that was co-developed with JBL to provide natural low frequency extension at any signal level.
Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay for system
optimization. With the ZonePro? every tool is at your disposal to maximize the response of
your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters.
The ZonePro? 640 and 641 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.
? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? Windows? 2000 and XP GUI
? IEC, UL and CSA Approvals
|
Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.
NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.
NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.
Specifications:
Network Connectors:
* Nomadlink Out: EtherCon housed RJ45
* Nomadlink In: EtherCon housed RJ45
* Ethernet rear-panel: EtherCon housed RJ45
* Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
* One Voltage sensing input: Two pole Phoenix
* Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
* Front operation locked: Yellow LED
* Fault warning: Red LED
* Amplifier subnet muted: Red LED
* NomadLink network connected/activity: Blue LED
* Ethernet connected: Orange LED
* Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption:
Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)
|
Reviews
There are no reviews yet.