Content |
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch | Behringer DCX2496 Overview
The DCX2496 ULTRADRIVE PRO from Behringer is a digital loudspeaker management system, that provides excellent audio quality, along with a comprehensive feature list. It allows for precise set-up of multiple loudspeaker arrays, suitable for live sound, fixed installations that require control of loudspeaker systems, and other contractor-installed applications.
Each of the three-inputs and six-outputs have fixed processing blocks, including gain, delay, EQ and dynamic EQ on the input channels, and gain, crossover, EQs, limiter and delays on the output side. One of the inputs can accept a stereo AES/EBU digital signal. An integrated sample rate converter assists in accepting various sample rates. Additionally, an internal input-sum signal is easily set-up.
Four different mono and stereo output operating modes are available, all with individual crossover filter types with selectable roll-off characteristics. Input and output delays allow for time adjusting signals to compensate for ambient temperature changes or for adjusting arrival time differences for individual speaker clusters. EQs can be used for both musical enhancement or for level-dependent equalization. Brick-wall limiters guarantee speaker protection.
Remote control of one or several units can be accomplished utilizing downloadable software for a Windows based computer. Set-ups can be saved to the software, or to an optional PCMCIA card for the ultimate in portability. Servo-balanced, gold-plated XLR connectors for all inputs and outputs guarantee excellent connectivity.
- Three-input, six-output loudspeaker management system
- Four different mono- and stereo-output operating modes
- Individual crossover filter types including Butterworth, Bessel and Linkwitz-Riley, with selectable roll-off characteristics from 6dB to 48dB per octave
- Choice of high-, band- and low-pass filters for each input and output
- Dynamic EQ for level-dependent equalization and parametric EQ selectable for each channel
- “Zero" attack limiters on all output channels for optimal signal protection
- Automatic or manual-adjustable delays for all inputs and outputs allow for adjustment due to room temperature, phase and arrival time differences
- Link option via RS-485 network interface allows for linking multiple units for larger installation requirements
- Downloadable software enables single- or multiple-unit remote control utilizing a Windows based computer
- Sixty user-defined internal presets can bestored via software or on a PCMCIA card
- Internal universal power supply allows the unit to operate virtually anywhere
Frequency Response |
10Hz to 35kHz, -1dB |
Dynamic Range |
109dB |
Input Connections |
3 x XLR |
Output Connections |
6 x XLR |
Input Impedance |
20kΩ @ 1kHz |
Output Impedance |
160Ω @ 1kHz |
Maximum Input Level |
+22dBu |
Maximum Output Level |
+22dBu |
Sample Rate |
32kHz to 96kHz |
RTA Mic Phantom Voltage |
+15V |
Crosstalk (Main Outputs) |
-100dB @ 10dBu In |
THD & Noise |
0.007% @ 0dBu In |
Dimensions |
19" x 8.5 x 1.75" (483 x 217 x 45mm) |
Weight |
6.6 lbs (3 kg) |
| The LD Systems X223 is a stereo 2 way / mono 3 way crossover in standard 19"/1U rack format. Its rugged construction, high quality and robust knobs as well as the integrated power unit are rarities in this price range. It provides a mono sub output, an adjustable crossover frequency for each channel, adjustable LF/HF and input gains, phase reverse controls, switchable 40 Hz High-Pass filters and symmetrical XLR In- and Outputs. With the LD Systems X223 you get a crossover fulfilling the professional standards and offering great quality and sound characteristics.
Product type
Signal Processors
Version
2-way stereo/3-way mono
Frequency response
20 - 20.000 Hz
Signal-to-noise ratio
> 93 dB
Total Harmonic Distortion (THD)
< 0.004 %
Crosstalk
< - 80 (20 - 20.000 Hz) dB
Max. input level
+21 (balanced or unbalanced) dBu
Max. output level
+21 (balanced or unbalanced) dBu
Input impedance (kOhms)
50000 kOhm
Output impedance
200 Ohm(s)
Controls
2 x crossover frequency low/high, 2 x crossover low/mid, 2 x high gain, 2 x highpass (40 Hz), 2 x input gain, 2 x low gain, 2x frequency switch x1/x10, 4 x inv switch, LF sum, Mono/stereo mode
Indicators
2 x clip, 2 x crossover x 10, 2 x highpass, 4 x inv., mono, stereo
Line input connectors
XLR
Line output connectors
XLR
Mains connector
IEC socket
Operating voltage
220 V AC - 240 V AC
|
The LD DPA260 is a 6-Channel 19" Speaker Processor for our VA-4, VA-8 and UNO-Array with plenty of useful setups for each system
- Type: DSP Controller for Line Array VA-4, VA-8 and UNO
- Model Name: DPA-260
- Description: 6-Channel 19" speaker processor, 32bit DSP, 24bit AD/DA (48 kHz) converter
- Inputs: 2 Channels Analog/Digital, L + R, Noise Gate, the inputs and outputs are freely assignable, that means you can assign any input to any output and vice versa
- Input EQ: 5 Band PEQ, Low Shelf and High Shelf Types available
- Crossover Range: 20 Hz - 20 kHz
- Outputs: 6 Channels, High/Low Pass Filter, Filtertype and dB available, 7 Band PEQ, Low Shelf and High Shelf Types available, Limiter with Threshold, Attack and Release Parameters
- Delay: Time or Meter available, Max. Delay up to 848 ms
- Phase Invert Function: USB Port, Full programmable Software included with 24 Memory Capacity for Presets
- Display: 2 × 16 character LCD with backlight
- Switch mode power supply: 90 V - 250 V
- Dimensions: 19" / 1U
|
With the DSP 260 digital 2-in-6 sound system manager, DYNACORD is continuing its proud tradition in the fi eld of innovative digital signal processors. Based on the most modern hardware, this system manager offers tried-and-tested as well as new algorithms for the simple and swift construction of active multi-way systems. As much importance has been attached here by the developers to high user-friendliness as to the realization of an extremely favorable price. 24-bit sigma-delta AD/DA converters and a 32-bit floating-point signal processor make possible a dynamic range of 111 dB. In addition to the two analog inputs, a digital stereo input in AES/EBU format is available. A -6 dB pad switch in front of the AD converters offers additional security against overload when the device is connected to mixing desks with very high output levels. The 6 individually mutable outputs are electronically balanced and available on XLR sockets. For all inputs and outputs, easily read LED level meters are provided on the front panel. Users can choose whether to configure their own systems at the device itself using the controls and display provided or else by means of the intuitive editing software. 3-way stereo, 2-way stereo + FR, 4-way mono + FR etc. Furthermore, factory presets compatible with those of the tried-and-tested DSP-244 are available for Dynacord loudspeaker systems. In terms of DSP, the device offers parametric and graphic EQs as well as a delay function in the input and crossover, channel EQ, channel delay and a level control with limiter in each output channel. An RS-232 interface allows Master/Slave operation of multiple devices as well as GPI switching of settings. A PC (the editing software runs under Windows) can be connected via the USB interface on the front panel. A variable parameter lockout function allows you to determine which settings and parameters can be accessed directly at the device. This is just one of many features that make the DSP 260 an ideal choice also for the rental business. The wealth of features combined with its outstanding audio performance and favorable price commend this audio system manager for a multitude of professional applications. General Mains Voltage 100-240 VAC 50-60 Hz Power Consumption 25W Audio Analog Inputs 2x XLR IN, electronically balanced, 2x XLR THRU OUT, electronically balanced Digital Inputs 1x XLR AES/EBU IN Nominal Input Voltage 1.23 V / +4 dBu Maximum Input Voltage (Without -6dB Analog Pad Engaged) 8.7 V / +21 dBu Input Impedance 10k ohm Common Mode Rejection -80 dB @ 1 kHz (typical) A/D Conversion 24-Bit Sigma-Delta Outputs 6x XLR OUT, electronically balanced Nominal Output Voltage 1.23 V / +4 dBu Maximum Output Voltage 8.7 V / +21 dBu Output Impedance 50 ohm D/A Conversion 24-Bit Sigma-Delta Frequency Response 10 Hz-22 kHz (+/- 0.5 dB) THD+N < 0.01% (band limited 22Hz-22kHz) Dynamic Range 111 dB unweighted, band limited 22 Hz - 22 kHz Interfaces USB USB Type B on front panel (PC Interface) 9-pin DSUB Software Confi gurable for GPI Preset Recall or Master/Slave Connection to second DSP 260 unit Signal Processing Sample Rate 48 kHz Data Format 24-Bit Internal Processing 32-Bit Floating Point Physical Dimensions (WxHx) 19 x 14 x 1.75 inches (482.6 x 355.6 x 44.45 mm) Weight (Net) 10.1 lb (4.6 kg) Weight (Gross) 13.0 lb (5.9 kg)
| Digital stereo active crossover with 4 inputs and 8 outputs, incl. software .
- Flexible routing configurations for all standard mono and stereo output operating modes
- 4 analog inputs and 8 analog outputs (XLR)
- Active frequency filter types (Bessel, Butterworth and Linkwitz-Riley) with slopes up to 24 dB/octave split up the audio signal into different frequency bands
- Incl. software editor (for PC and Mac) for remote control via computer through USB interface: store, transfer, and manage your presets
- Up to 30 user presets storable in the device via software
- 5 menu languages selectable (German, English, French, Spanish, Dutch)
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
- Mute switch with LED indicator per output
- 7-band parametric EQ per output
- Up to 7 ms signal delay adjustable for the outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase
- Lock function for prevents undesired changes to settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 10 and Mac OS X 10.5.8 and better
- Digital signal processor
- The device can be connected via USB to the PC in connection with DXO Software
The firmware can be updated via the PC connection
- (19") 48.3 cm rack installation 1 U
Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Power connection: |
Mains input via Coaxial power connector (M) power supply cord with AC adapter (provided) |
Frequency range: |
10 - 22000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Digital signal processor |
Crossover frequency: |
20-20000 Hz |
Impedance: |
Input 10 kOhm
Output 50 Ohm |
Gain: |
Output: -50 dB to +12 dB |
Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Delay: |
0 - 7 ms |
Dynamic range: |
Input: 114 dB
Output: 110 dB |
Sample rate: |
48 kHz |
Connections: |
Input: line via 4 x 3-pin XLR
Output: line via 8 x 3-pin XLR |
Max. level: |
Input: +22 dBu
Output: +9 dBu |
USB port: |
Typ B |
PC connect: |
DXO Software via USB, firmware can be updated |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimensions: |
Width: 48,3 cm
Depth: 22,3 cm
Height: 4,45 cm |
Weight: |
1,90 kg |
|
Reviews
There are no reviews yet.