| Content | PS418D
Pre-Amplifier
The condenser miniature microphones, need phantom power to work. The PS418D is just what they need. It can be powered by phantom power or battery, and switchable low cut filter helps to reduce low band noise.
Features:
• Two options for Power Requirements: phantom or battery.
• Low-cut filter switch.
• Transistor output transformer circuit.
Specification:
Frequency Response: 25-20,000 Hz
Output Impedance: phantom 200Ω; battery 270Ω
Min. Load Impedance : 1000Ω
Power Requirements: phantom 9-52VDC，2mA; battery 1.5V AA/UM3
Low Frequency Filter: 80Hz @ 12dB / oct
Connector: TA3M (input), XLR3M (output)
Dimension(WxHxD): 63X84X22.5mm (2.48"x3.3"x0.89")
Weight: 245 g
Packaging: white box | The Gravity MA 3D A lets you attach microphones, action cams and mobile phone holders to your microphone stand, and set them up flexibly. Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws.
Material: Plastic , Polyamide
Joint adjustment: Wing screw
Joint rotation: 360°
Joint tilt: 180°
Arm length: 400 mm
Suitable for mounting on: Microphone Stands
Suitable for tube diameter: 15 mm - 35 mm
Colour: Black
Thread size: 3/8”
Weight: 0,302 kg
|
The new AT8657/LED table-mount microphone adapter adds functionality to quick-mount gooseneck models from the Audio-Technicaʼs Engineered Sound, Unipoint and ProPoint installation mic ranges and ES945 and ES947 boundary microphone models.
The new AT8657/LED features a touch-sensitive capacitive switch surrounded by an illuminated LED status ring that can be set between red (mute) and green (on). Its integrated 3-pin XLR allows the table-mounting of gooseneck microphones with XLR connectors while the AT8657/LED has a 5-pin XLR out for audio and control data.
AT8657LED Specifications 270 KB
|
Features
- Connects directly to network via Ethernet cable—no soldering or additional cable required
- Integrated user switch controls talk/mute in Local mode and triggers Dante-enabled devices in Remote mode
- Local or remote control of gain, low-cut UniSteep® filter, red/green LED status indicator and phantom power
- Powered by network PoE
- Scalable across Danteʼs 512 bidirectional audio channels
- Touch-sensitive capacitive-type user switch
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- 3-pin XLRF-type input for quick mounting of any gooseneck microphone with an XLRM-type output
- Heavy die-cast case and non-slip silicone foam bottom padsminimize coupling of surface vibration to the microphone
Description
The ATND8677 is a Dante-enabled microphone desk stand for use with any gooseneck microphone with a three-pin XLRM-type output connector. The desk stand is designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup applications.
The desk stand features a touch-sensitive capacitive-type user switch with integral red/green LED status indicator. In Local mode the user switch mutes and unmutes the microphone. It can be set to toggle between live and muted audio (toggle on/off), to permit live audio only while the switch is pressed (press to talk), or to mute the audio while the switch is pressed (press to mute). In Remote mode the user switch can be used to trigger functions on compatible Dante-enabled devices, such as a video cameraʼs pan/tilt or a roomʼs lighting preset. While in Remote mode the desk standʼs audio output is controlled remotely. An integral 80 Hz low-cut UniSteep® filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations. A three-position input gain level selector permits trim adjustment to accommodate louder and softer voices. The desk stand provides 12V DC phantom power by default, which can be switched off and on.
The gain, low-cut UniSteep® filter, red/green LED status indicator and phantom power can all be controlled locally or remotely via third-party software.* Recessed buttons on the bottom of the desk stand allow user to configure the desk stand settings locally. Audio, low-cut, gain and phantom power settings can be locked in Local mode by pressing and holding the lock button. This lock will prevent end users from adjusting the settings. Default settings for the stand are as follows: audio toggle on/off (with audio muted at power up), low-cut filter off, +30 dB input gain, phantom power on.
- Frequency response: 20-20,000 Hz
- Low frequency roll-off: 80 Hz, 18 dB/octave
- Input impedance: 1.4 kO
- Maximum input levels: -10 dBu @ +30 dB gain / -20 dBu @ +40 dB gain / -30 dBu @ +50 dB gain
- Signal-to-noise ratio1: 68 dB, 1 kHz at 1 Pa
- Power requirements: PoE IEEE802.3af standard
- Power consumption: 1.5W
- Microphone phantom power: 12V DC
- Switches: Local Mode: Touch-sensitive capacitivetype user switch function: toggle (mute on power up), toggle (talk on power up), momentary on, momentary off; Low-cut filter: flat, roll-off; Gain: +30 dB, +40 dB, +50 dB; Phantom power: 12V DC, off Remote Mode: Low-cut and Gain via third-party software*
- Weight: 770 g (27.2 oz)
- Dimensions: 133.0 mm (5.24“) maximum length, 93.8 mm (3.69“) maximum width, 46.2 mm (1.82“) maximum height
- Input connector: 3-pin XLRF-type
- Output connector: Physical level: standard Ethernet
- Dante network:Connector: single RJ45 | Cable quality: Shielded CAT5 or CAT6 recommended | Transmission speed: 100 Mbps
|
The RØDE invisiLav is designed to aid the concealing of the Lavalier and smartLav microphones.
Its soft construction absorbs noise and vibration, while the wide, flat profile provides coverage from the elements and allows for versatile mounting. There's two mounting points in case a redundant mic is required, and cable management on the side.
Available in either a pack of three or a bulk pack of ten, the invisiLav comes with pre-cut, skinsafe adhesive that can be used to stick the invisiLav to either the body or to fabric. The invisiLav itself is also made from a medical grade skin safe material so it can be mounted on the body without fear of irritation.
|
The K6 powering module is the heart of this Sennheiser professional modular
microphone system and can be powered either by its internal 'AA' size 1.5 V
battery or by 12 - 48 V phantom power. The K6 can be combined with different
condenser microphone heads to provide a wide variety of polar patterns. Matt
black, anodised scratch-resistant finish.
Profile
Powering module for battery/phantom powering with switchable roll-off filter, battery
on/off switch with battery test. Suitable for ME 62 - ME 67 microphone heads and
-60 versions of MKE microphones.Transmission factor 0 dB at 1 kHz, nominal
impedance 200 Ohm, min. terminating impedance 1 kOhm, max. output voltage 2 V
(at 1 kHz), power supply: phantom powering 12 - 48 V or 1.5 V (AA size)alkaline
battery, supply current 2.2 mA, battery life approx. 150 h, dimensions in mm:
? 22 x 155, resultant length 94 mm, weight approx. 45 g.
Features
Switchable bass roll-off filter protects against rumble, handling, pop and wind noise
On/off switch with battery test
High output, low noise
Transformerless balanced output on 3-pin XLR connector
Delivery Includes
1 K6 powering module
1 MZQ 200 microphone clamp
1 AA battery
1 protective carrying case
Technical Data
Nominal impedance 200 Ohm
Min. terminating impedance 1000 Ohm
Output voltage 2 V
Power supply Phantom 12 - 48 V 1x Typ IEC LR 06
Current consumption 2,2 mA
Operating time (Battery) max. 150 h
Dimensions d 22 x 94 mm (netto)
Weight ca. 45 g
Gain 0 dB
|
Reviews
There are no reviews yet.