User\’s manual Software user\’s manual Firmware & Software 4 channels with DSP control Purpose-designed for CURV 500® installations Low-profile 1U 19″ rackmount construction Drives up to six CURV 500® satellites or one CURV 500® ISUB subwoofer per channel Single push encoder operation High-contrast OLED display Temperature controlled low-noise fan High-efficiency switch mode power supply Only […]
Drives up to six CURV 500® satellites or one CURV 500® ISUB subwoofer per channel
Single push encoder operation
High-contrast OLED display
Temperature controlled low-noise fan
High-efficiency switch mode power supply
Only 6.8 kg
Purpose-designed for CURV 500® installations the iAMP® is a low-profile 4-channel Class D rackmount amplifier with high-efficiency switch mode power supply and 10 Hz – 22 kHz frequency response. Sporting DSP control with presets for various satellite and subwoofer configurations, delay and parametric EQ each channel delivers 240 watts RMS at 4 ohms with less than 0.01% THD.
Operating the iAMP® is simple and intuitive with just a single push encoder and easily readable high-contrast OLED display. It features a soft start circuit, DC, overcurrent, thermal and short circuit protection plus a temperature controlled low- noise fan. Input is on balanced XLR and terminal block connectors. The iAMP® is capable of driving up to six CURV 500® satellites or one CURV500ISUB subwoofer per channel providing terminal block and speakON-compatible output connectors.
Product type
Power Amplifiers
Type
Installation Power Amplifiers
Rated ouput power (1kHz @ 2,7 Ohms)
4 x 240 W
Rated ouput power (1kHz @ 4 Ohms)
4 x 240 W
Rated ouput power (1kHz @ 8 Ohms)
4 x 120 W
Rated ouput power (1kHz @ 16 Ohms)
4 x 60 W
Output circuitry
Class D
Frequency response
10 – 22000 Hz
THD
< 0,01 %
Protection circuits
DC , over-current , short circuit , soft start , thermal overload
Drives up to six CURV 500® satellites or one CURV 500® ISUB subwoofer per channel
Single push encoder operation
High-contrast OLED display
Temperature controlled low-noise fan
High-efficiency switch mode power supply
Only 6.8 kg
Purpose-designed for CURV 500® installations the iAMP® is a low-profile 4-channel Class D rackmount amplifier with high-efficiency switch mode power supply and 10 Hz – 22 kHz frequency response. Sporting DSP control with presets for various satellite and subwoofer configurations, delay and parametric EQ each channel delivers 240 watts RMS at 4 ohms with less than 0.01% THD.
Operating the iAMP® is simple and intuitive with just a single push encoder and easily readable high-contrast OLED display. It features a soft start circuit, DC, overcurrent, thermal and short circuit protection plus a temperature controlled low- noise fan. Input is on balanced XLR and terminal block connectors. The iAMP® is capable of driving up to six CURV 500® satellites or one CURV500ISUB subwoofer per channel providing terminal block and speakON-compatible output connectors.
Product type
Power Amplifiers
Type
Installation Power Amplifiers
Rated ouput power (1kHz @ 2,7 Ohms)
4 x 240 W
Rated ouput power (1kHz @ 4 Ohms)
4 x 240 W
Rated ouput power (1kHz @ 8 Ohms)
4 x 120 W
Rated ouput power (1kHz @ 16 Ohms)
4 x 60 W
Output circuitry
Class D
Frequency response
10 - 22000 Hz
THD
< 0,01 %
Protection circuits
DC , over-current , short circuit , soft start , thermal overload
Controls
Push encoder
Indicators
OLED Display
Line inputs
4
Line input connectors
terminal block , XLR
Loudspeaker outputs
4
Speaker output connections
Speakon compatible , terminal block
Cooling
temperature controlled low-noise fan, noiseless in idle mode
Operating voltage
Switching power supply
Power consumption @ full load
1100W
Operating voltage
100 V AC - 240 V AC, 50 - 60 Hz , Switch mode power supply with power factor correction (PFC)
Width
482 mm
Height
44 mm
Depth
420 mm
Weight
6,8 kg
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
OUTPUT POWER
T-604
T-1204
T-1208
T-2408
RMS, 1kHz, 1.0% THD+N
4 ohms
4x 160 W
4x 320 W
8x 150 W
8x 300 W
8 ohms
4x 115 W
4x 220 W
8x 100 W
8x 195 W
Bridge @ 8ohms
2x 320 W
2x 640 W
4x 300 W
4x 600 W
Pink Noise 12dB CF
4 ohms
4x 210 W
4x 415 W
8x 180 W
8x 370 W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.