LD Systems DEEP2 2400 X PA Power Amplifier 2 x 1200 W 2 ohm

799.00 incl. GR VAT

In stock

EAN: 4049521111846
Installments calculation
CompareAdd to wishlist Submit Better Price
The DP2400X is the newest member of the DEEP2 family of power amplifiers. In response to requests by many customers, we expanded this series with a new, powerful amplifier that is also compatible with 2-ohm systems. The key specifications are 2 x 1200 W at 2 ohms, 2 x 950 W at 4 ohms and […]

 

Read more

The DP2400X is the newest member of the DEEP2 family of power amplifiers.

In response to requests by many customers, we expanded this series with a new, powerful amplifier that is also compatible with 2-ohm systems. The key specifications are 2 x 1200 W at 2 ohms, 2 x 950 W at 4 ohms and 2 x 600 W at 8 ohms RMS power. Like the other power amplifiers in the DEEP2 series, the DP2400X uses class H circuitry powered by a conventional power supply. The protective circuitry is also identical with that used in the DEEP2 series. It also follows the DEEP2 design in its integration of two temperature-dependent two step cooling fans. One special feature is a switchable 12 dB low-cut and/or 12 dB low-pass filter adjustable from 25 Hz to 150 Hz on both channels. This makes it possible to use the DP2400X as a bass amp or even realize a powerful bi-amping system. With the filters switched off, it becomes a conventional 2 channel power amp.

Product type
Power Amplifiers


Type
PA Power Amplifiers


Rated ouput power (1kHz @ 2 Ohms)
2 x 1200 W


Rated ouput power (1kHz @ 4 Ohms)
2 x 950 W


Rated ouput power (1kHz @ 8 Ohms)
2 x 600 W


Rated ouput power (1kHz @ 4 Ohms, bridged)
2200 W


Rated ouput power (1kHz @ 8 Ohms, bridged)
1800 W


Output circuitry
Class H


Frequency response
20 – 20000 Hz


THD
< 0.1 %


Signal-to-noise ratio
106 dB


Damping factor
> 450


Crosstalk
>76 dB


Gain
39 dB


Input sensitivity
0.775 V


Protection circuits
clip limiter , DC protection , short circuit , thermal overload


Controls
2 x highpass/lowpass (switchable) , 2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)


Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal


Loudspeaker outputs
2


Speaker output connections
Speakon compatible , Terminal posts


Cooling
highly efficient, automatic


Operating voltage
transformer


Operating voltage
230 V AC / 50-60 Hz


Weight
17,6 kg


Features
Volex mains socket

Weight 17.60 kg

Reviews

There are no reviews yet.

Be the first to review “LD Systems DEEP2 2400 X PA Power Amplifier 2 x 1200 W 2 ohm”

Your email address will not be published. Required fields are marked *

Quick Comparison

LD Systems DEEP2 2400 X PA Power Amplifier 2 x 1200 W 2 ohm removeBITTNER AUDIO BASIC 1200-2x600W-4Ω POWER AMPLIFIER removeQSC GX-5 POWER AMPLIFIER 2x700W RMS @ 4Ω, 2x500W RMS @ 8Ω removeQSC GX-7 POWER AMPLIFIER 2x1000W RMS @ 4Ω, 2x725W RMS @ 8Ω removeRAM AUDIO S-1500 Power Amplifier 2x880 Watts removeCrown DSI-2000 2x800W-4Ω Power Amplifier remove
NameLD Systems DEEP2 2400 X PA Power Amplifier 2 x 1200 W 2 ohm removeBITTNER AUDIO BASIC 1200-2x600W-4Ω POWER AMPLIFIER removeQSC GX-5 POWER AMPLIFIER 2x700W RMS @ 4Ω, 2x500W RMS @ 8Ω removeQSC GX-7 POWER AMPLIFIER 2x1000W RMS @ 4Ω, 2x725W RMS @ 8Ω removeRAM AUDIO S-1500 Power Amplifier 2x880 Watts removeCrown DSI-2000 2x800W-4Ω Power Amplifier remove
Image
SKULDDP2400XBASIC1200010001010002S-1500DSI-2000
Rating
Price 799.00 incl. GR VAT 1,068.39 incl. GR VAT 589.00 incl. GR VAT 695.00 incl. GR VAT 1,160.64 incl. GR VAT 1,161.00 incl. GR VAT
Stock

In stock

Available on backorder

In stock

Available on backorder

Available on backorder

Available on backorder

AvailabilityIn stockAvailable on backorderIn stockAvailable on backorderAvailable on backorderAvailable on backorder
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentThe DP2400X is the newest member of the DEEP2 family of power amplifiers. In response to requests by many customers, we expanded this series with a new, powerful amplifier that is also compatible with 2-ohm systems. The key specifications are 2 x 1200 W at 2 ohms, 2 x 950 W at 4 ohms and 2 x 600 W at 8 ohms RMS power. Like the other power amplifiers in the DEEP2 series, the DP2400X uses class H circuitry powered by a conventional power supply. The protective circuitry is also identical with that used in the DEEP2 series. It also follows the DEEP2 design in its integration of two temperature-dependent two step cooling fans. One special feature is a switchable 12 dB low-cut and/or 12 dB low-pass filter adjustable from 25 Hz to 150 Hz on both channels. This makes it possible to use the DP2400X as a bass amp or even realize a powerful bi-amping system. With the filters switched off, it becomes a conventional 2 channel power amp. Product type Power Amplifiers
Type PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms) 2 x 1200 W
Rated ouput power (1kHz @ 4 Ohms) 2 x 950 W
Rated ouput power (1kHz @ 8 Ohms) 2 x 600 W
Rated ouput power (1kHz @ 4 Ohms, bridged) 2200 W
Rated ouput power (1kHz @ 8 Ohms, bridged) 1800 W
Output circuitry Class H
Frequency response 20 - 20000 Hz
THD < 0.1 %
Signal-to-noise ratio 106 dB
Damping factor > 450
Crosstalk >76 dB
Gain 39 dB
Input sensitivity 0.775 V
Protection circuits clip limiter , DC protection , short circuit , thermal overload
Controls 2 x highpass/lowpass (switchable) , 2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators level , Limit , Power , Protect (protection circuit engaged) , Signal
Loudspeaker outputs 2
Speaker output connections Speakon compatible , Terminal posts
Cooling highly efficient, automatic
Operating voltage transformer
Operating voltage 230 V AC / 50-60 Hz
Weight 17,6 kg
Features Volex mains socket

BASIC Series - Intelligent Power

BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.

Certainly more than basic!

High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty

TECHNICAL DATA:
Basic 1200:  2x 600 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  > 400 @ 4 Ohm
Cooling:  2x Fan (temp. reg. variable speed)
Weight:  15 kg.
Dimensions : 2 RU / 483 x 88 x 454 mm (19" x 3.5" x 17.9“)

- Signal to Noise (20 Hz - 20 kHz): 100 dB
- Input Sensitivity: 1.2 Vrms
- Voltage Gain (8 Ohms): 34.4 dB
- Output Circuitry: 2-tier Class H
- Power Requirements: 6A
- Frequency Response: 20 Hz - 20 kHz, +0, 1 dB
- Dynamic Headroom (4 Ohms): 2 dB
- Damping Factor: 100
- Input Impedance: Greater than 20k (balanced)
- Maximum Input Level: +24 dB (16 Vrms)
- Input Connectors (each channel): 3-pin XLR and 1/4-inch TRS, balanced, parallel Phono, unbalanced
- Output Connectors (each channel): Speakon, 1/4-inch, Binding Posts
- Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection Load protected against DC faults
- Rear Panel Controls: Full Range / Crossover switch
- Dimensions (H x W x D): 3.5 x 19 x 10.1 inches (89 mm x 483 mm x 257 mm)
- Weight: 26 lbs (12 kg)

Front Panel Controls and Indicators:
- Gain controls, 21 detents
- Red Clip LEDs, proportional, 0.1% THD threshold
- Green Signal LEDs, threshold -35 dB
- Blue Power LED, AC on


Stereo Mode:
- 8 Ohms / both channels driven: 500 Watts
- 8 Ohms / single channel driven: 600 Watts
- 4 Ohms / both channels driven: 700 Watts
- 4 Ohms / single channel driven: 850 Watts

Distortion:
- 8 Ohms: less than 0.05%
- 4 Ohms: less than 0.1%

Dimensions and Weight in Packaging
Shipping Weight: 31 lbs
Shipping Dimensions: 24 x 15 x 7 in

- Power levels matched to the most popular speakers used by entertainers
- Optimized for maximum real-world headroom into 4 ohm and 8 ohm speaker systems
- Inputs: XLR, 1/4" TRS and phono input connectors for compatibility with any source
- Outputs: Speakon(R) combo accepts, 1/4" (TS) plugs or Speakon 2-pole and 4-pole plugs (connects 2 poles only). Binding posts support all other speaker wiring systems
- Minimum depth chassis (10.1“/257 mm) fits in compact, inexpensive effects racks
- Lightweight - GX7 is only 15.5 lbs (7 kg)
- Detented gain controls for precise setting and matching of sensitivity
- GuardRail(TM) automatically protects the amplifier and loudspeakers from damage due to temperature rise or overdrive without shutting down the show
- Front panel LEDs monitor Power, Signal and Clipping
- Subwoofer/Satellite crossover built-in
- 230V 16.5 lbs (7.5 kg)

OUTPUT POWER S-1500 S-2000 S-3000 S-4000 S-6000 S-3004 S-4004 S-4044 S-6004 S-6044
1kHz, 1.0% THD
2 ohms 2x880W 2x1190W 2x1570W 2x1950W 2x2950W 4x700W 4x980W - 4x1440W -
4 ohms 2x575W 2x790W 2x1100W 2x1380W 2x2025W 4x500W 4x670W 4x975W 4x1000W 4x1480W
8 ohms 2x325W 2x460W 2x630W 2x810W 2x1250W 4x300W 4x430W 4x690W 4x620W 4x1015W
Bridge @ 4ohms 1760W 2380W 3140W 3900W 5900W 2x1400W 2x1960W - 2x2880W -
Bridge @ 8ohms 1150W 1580W 2200W 2760W 4050W 2x1000W 2x1340W 2x1950W 2x2000W 2x2960W
P. N. 12dB C.F.
2 ohms 2x975W 2x1360W 2x2060W 2x2460W 2x4225W 4x890W 4x1170W - 4x2080W -
4 ohms 2x610W 2x880W 2x1240W 2x1600W 2x2600W 4x580W 4x820W 4x1230W 4x1280W 4x2110W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™

Crown DSi 2000 2x800W-4Ω Power Amplifier

The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.

The outputs shall be usable as stereo or bridged-mono modes of operation.

The bridged-mono mode shall bridge the outputs to provide increased output voltage.

Front panel controls and indicators shall include the following:

Level: Detented rotary level control, one per channel.

Power Switch: On/off switch applies AC power to the amplifi er.

Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.

LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.

Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.

?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.

?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.

Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.

Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.

Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.

Rear panel controls and connectors shall include the following:

AC Line Connector: NEMA 5-15P (15A).

Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.

Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.

HiQnet USB Connector: Type B, connects to a HiQnet network.

HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.

The amplifier shall have the following specifications:

Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm

Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W

with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-

Mono: 1,600W with 0.5% THD.

Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.

Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.

Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo

mode, 4 to 16 ohms in Bridge-Mono mode.

Sensitivity at 8 ohm rated output: 3.09V.

Sensitivity at 4 ohm rated output: 2.84V.

Sensitivity at 2 ohm rated output: 2.24V.

Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB

(A weighted).

Damping Factor: Better than 500 from 20 Hz to 500 Hz.

Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.

Input Stage: Input is electronically balanced and employs precision 1% resistors.

Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.

Maximum Input Signal: +22 dBu typical.

Weight17.60 kg15.00 kg12.60 kg7.00 kg8.00 kg9.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 17.60 kg
Weight 15.00 kg
Weight 12.60 kg
Weight 7.00 kg
Weight 8.00 kg
Weight 9.00 kg