LD Systems DJ800 Power Amplifier 2 x 400 W 4 Ohm

Discontinued

350.00 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price

LD Systems DJ800 Power AmplifierThe DJ800 is the most powerful power amplifier in LD Systems’ DJ series. The dependable Class AB design has an output of 400W per channel @ 4 ohms, 2x 240W @ 8 ohms and 800W in switchable bridge mode. Weighing in at just 10 kg, it is perfect for mobile use, but also for installation.

The DJ800 is equipped with extensive protection circuitry and a power-on delay. The front panel perforations and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch eliminates ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.

The DJ800 functions in the entire frequency range of 20Hz – 20kHz with maximum dependability, dynamics, and impulse fidelity.

LD Systems DJ800 Power AmplifierThe DJ800 is the most powerful power amplifier in LD Systems’ DJ series. The dependable Class AB design has an output of 400W per channel @ 4 ohms, 2x 240W @ 8 ohms and 800W in switchable bridge mode. Weighing in at just 10 kg, it is perfect for mobile use, but also for installation.

The DJ800 is equipped with extensive protection circuitry and a power-on delay. The front panel perforations and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch eliminates ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.

The DJ800 functions in the entire frequency range of 20Hz – 20kHz with maximum dependability, dynamics, and impulse fidelity.

 

Read more

LD Systems DJ800 Power AmplifierThe DJ800 is the most powerful power amplifier in LD Systems’ DJ series. The dependable Class AB design has an output of 400W per channel @ 4 ohms, 2x 240W @ 8 ohms and 800W in switchable bridge mode. Weighing in at just 10 kg, it is perfect for mobile use, but also for installation.

The DJ800 is equipped with extensive protection circuitry and a power-on delay. The front panel perforations and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch eliminates ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.

The DJ800 functions in the entire frequency range of 20Hz – 20kHz with maximum dependability, dynamics, and impulse fidelity.

Weight 11.00 kg

Reviews

There are no reviews yet.

Be the first to review “LD Systems DJ800 Power Amplifier 2 x 400 W 4 Ohm”

Your email address will not be published. Required fields are marked *

Quick Comparison

LD Systems DJ800 Power Amplifier 2 x 400 W 4 Ohm removeLD Systems LDDP600 Power Amplifier 2 x 300W 8 Ohm removeInterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm removeRCF HPS 1500: CLASS H PROFESSIONAL POWER AMPLIFIER removeDYNACORD SL-1200 / 230V 1200 Watts 8Ω removeCROWN DSI-1000 2x500W-4Ω POWER AMPLIFIER remove
NameLD Systems DJ800 Power Amplifier 2 x 400 W 4 Ohm removeLD Systems LDDP600 Power Amplifier 2 x 300W 8 Ohm removeInterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm removeRCF HPS 1500: CLASS H PROFESSIONAL POWER AMPLIFIER removeDYNACORD SL-1200 / 230V 1200 Watts 8Ω removeCROWN DSI-1000 2x500W-4Ω POWER AMPLIFIER remove
Image
SKULDDJ800LDDP600V-1000HPS1500E009274DSI-1000
Rating
Price 350.00 incl. GR VAT 450.00 incl. GR VAT 330.26 incl. GR VAT 596.44 incl. GR VAT 830.00 incl. GR VAT 824.00 incl. GR VAT
Stock

Out of stock

In stock

In stock

Available on backorder

In stock

Only 1 left in stock (can be backordered)

AvailabilityOut of stockIn stockIn stockAvailable on backorderIn stockOnly 1 left in stock (can be backordered)
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
LD Systems DJ800 Power AmplifierThe DJ800 is the most powerful power amplifier in LD Systems' DJ series. The dependable Class AB design has an output of 400W per channel @ 4 ohms, 2x 240W @ 8 ohms and 800W in switchable bridge mode. Weighing in at just 10 kg, it is perfect for mobile use, but also for installation. The DJ800 is equipped with extensive protection circuitry and a power-on delay. The front panel perforations and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch eliminates ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit. The DJ800 functions in the entire frequency range of 20Hz - 20kHz with maximum dependability, dynamics, and impulse fidelity.
Content
LD Systems DJ800 Power AmplifierThe DJ800 is the most powerful power amplifier in LD Systems' DJ series. The dependable Class AB design has an output of 400W per channel @ 4 ohms, 2x 240W @ 8 ohms and 800W in switchable bridge mode. Weighing in at just 10 kg, it is perfect for mobile use, but also for installation. The DJ800 is equipped with extensive protection circuitry and a power-on delay. The front panel perforations and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch eliminates ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit. The DJ800 functions in the entire frequency range of 20Hz - 20kHz with maximum dependability, dynamics, and impulse fidelity.

The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W  2 Ohm

The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products. The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs. The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design. The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers

Type
PA Power Amplifiers

Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W

Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W

Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W

Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W

Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W

Output circuitry
Class H

Frequency response
20 - 20000 Hz

THD
< 0.1 %

Signal-to-noise ratio
105 dB

Damping factor
> 400

Crosstalk
>80 dB

Gain
35 dB

Input sensitivity
0.75 V

Protection circuits
clip limiter , DC protection , short circuit , thermal overload

Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)

Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal

Loudspeaker outputs
2

Speaker output connections
Speakon compatible , Terminal posts

Cooling
highly efficient, automatic

Operating voltage
transformer

Operating voltage
230 V AC / 50-60 Hz

Weight
12,8 kg

Features
Volex mains socket

InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz

high pass filter 30Ηz & 50Ηz

HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).

XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.

Features
Fast response and low distortion
Easy to configure in stereo / mono / bridge modes
Extensive protective circuits ensure high reliability and operating safety
Front panel signal / clip / protect LED indicators
Minimum load impedance (stereo / mono): 4 Ohm
XLR input connectors
SPEAKON output connectors
Switchable limiter

2 unit 19" rack, low weight for easy transportation

 

AMPLIFIER SPECIFICATIONS
Power output stereo 4Ω:2 x 750 Watt rms 
Power output stereo 8Ω:2 x 450 Watt rms 
Power output bridged 8Ω:1500 Watt rms 
Frequency Response:20 Hz ÷ 20 kHz  
Signal/noise rate:106 dB 
Damping factor:> 300 
Slew rate:50 V/μS 
INPUT SECTION
Input connector:xlr 
Input sensitivity:1.4 V (/ 32 – 26 dB) dBm/V RMS 
Input impedance: 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ 
OUTPUT SECTION
Output connector:Speakon 
SYSTEM PARAMETERS
Cooling:Forced 
Amplifier class:H 
POWER REQUIREMENT
Operating voltage:220 ÷ 240 V (50 / 60 Hz) V ~ Hz  
PHYSICAL SPECIFICATIONS
Height:88/3.4 mm/inch 
Width:482/18.9 mm/inch 
Depth:420/16.5 mm/inch 
Net Weight:17/37.4 Kg/Lbs

 

 

Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)

Engineered from the ground up for unmatched quality and performance,
the Crown? DSi Series of power amplifiers offers three models of 500W,
800W, and 1200W per channel at 4 ohms. Onboard digital signal processing
includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15
connector provides easy input/output connectivity between DSi amplifiers
and the new DSi-8M System Monitor.
The intuitive front panel LCD screen guides installers through a setup process?
featuring presets for the industry-standard JBL cinema loudspeaker systems?
to make configuration quick and easy.
At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched
performance with each award-winning JBL ScreenArray? system, making this the
ultimate cinema solution.

Features :
Includes three models of 500W, 800W, and 1200W per channel at 4 ohms
Automatic presets for popular JBL cinema speaker systems for quick, easy
configuration
Intuitive front-panel LCD screen guides installers through setup
Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting
Computer connectivity via USB allows fast setup and configuration with HiQnet?
System Architect? software
Rear-panel HD-15 connector provides easy input/output connectivity between DSi
amplifiers and new DSi-8M System Monitor
Switch-mode universal power supply
All products fill 2U rack spaces and weigh under 19 pounds
Barrier strip outputs, removable Phoenix-style input
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment
and guarantees its specifications

The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, fl ashes when a very low-level
signal is present at input.
?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or
excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo
(per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with
0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:
1,000W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 2.35V.
Sensitivity at 4 ohm rated output: 2.24V.
Sensitivity at 2 ohm rated output: 1.88V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also
adjustable high and low shelving fi lters.
Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave
and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per
channel.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL
system presets.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)

Weight11.00 kg13.00 kg10.30 kg20.00 kg14.80 kg10.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 11.00 kg
Weight 13.00 kg
Weight 10.30 kg
Weight 20.00 kg
Weight 14.80 kg
Weight 10.00 kg