Content | PA Power Amplifier 2 x 150 W 4 Ohm
User's manual
LD Systems DJ300 Power Amplifier
The DJ300 is a value-priced, full-featured Class AB power amplifier with an output of 150W per channel @ 4 ohms and 250W in 8-ohm bridge mode. Its sturdy construction paired with low weight makes it perfect for DJs in mobile use and smaller permanent installations.
It has extensive protection circuitry, a low-noise cooling fan, and a power-on delay. It uses XLR and stereo TRS sockets as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch helps eliminate ground loop hum. LEDs on the front panel next to the volume controls indicate functional status, overloading, and triggering of the protection circuit.
The DJ300 functions in the entire frequency range of 20Hz - 20kHz with high dependability, dynamics, and impulse fidelity.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 4 Ohms)
2 x 150 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 100 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
250 W
Output circuitry
Class A/B
Frequency response
20 - 20000 Hz
THD
0.05%
Gain
28 dB
Input sensitivity
0.85 V
Protection circuits
DC , over-current , short circuit , soft start , thermal overload
Controls
ground lift , mode , On / Off , volume
Indicators
clip , Power , protect (protection circuit engaged)
Line inputs
2
Line input connectors
6.3 mm Jack , XLR
Loudspeaker outputs
2
Speaker output connections
Speakon compatible , Terminal posts
Cooling
fan
Operating voltage
230 V AC
Width
483 mm
Height
88 mm
Depth
298 mm
Weight
8,5 kg |
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
|
HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.
Features |
---|
Fast response and low distortion | Easy to configure in stereo / mono / bridge modes | Extensive protective circuits ensure high reliability and operating safety | Front panel signal / clip / protect LED indicators | Minimum load impedance (stereo / mono): 4 Ohm | XLR input connectors | SPEAKON output connectors | Switchable limiter |
2 unit 19" rack, low weight for easy transportation
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 750 Watt rms | | Power output stereo 8Ω: | 2 x 450 Watt rms | | Power output bridged 8Ω: | 1500 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | 106 dB | | Damping factor: | > 300 | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | xlr | | Input sensitivity: | 1.4 V (/ 32 – 26 dB) dBm/V RMS | | Input impedance: | 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ | |
OUTPUT SECTION |
---|
Output connector: | Speakon | |
SYSTEM PARAMETERS |
---|
Cooling: | Forced | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220 ÷ 240 V (50 / 60 Hz) V ~ Hz | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88/3.4 mm/inch | | Width: | 482/18.9 mm/inch | | Depth: | 420/16.5 mm/inch | | Net Weight: | 17/37.4 Kg/Lbs |
|
| L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 300 Watt rms | | Power output stereo 8Ω: | 2 x 180 Watt rms | | Power output bridged 8Ω: | 600 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 6 A | | Power Consumption: | 1300 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 470 / 18.05 mm/inch | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
Reviews
There are no reviews yet.