Content | The DJ500 is a powerful, full-featured Class AB power amplifier with an output of 250W per channel 4 ohms and 500W in switchable bridge mode. It is especially suitable for mobile use by DJs and smaller bands and in permanent installations.
The DJ500 has extensive protection circuitry and a power-on delay. The half perforated front panel and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch helps eliminate ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.
The DJ500 functions in the entire frequency range of 20Hz - 20kHz with extremely high dependability, dynamics, and impulse fidelity.
- Type: 2-channel
- Output Power 1 KHz @ 4 ohms: 2 x 250 W
- Output Power 1 KHz @ 8 ohms: 2 x 150 W
- Output Power 1 KHz @ Bridge 8 ohms: 500 W
- Output Circuity: Class A/B
- Frequency Range: 20 - 20.000 Hz
- THD: 0,05%
- Voltage Gain: 30dB
- Input Sensivity: 0,85V
- Protection: Soft start, short circuit, DC, Temperature, over current
- Controls:ON/ OFF, Volume, Mode (Bridge/ Stereo), Ground-Lift
- Indicators: Power, Clip, Protect
- Connectors Line Input: 2 x XLR, 2 x 6,3mm jack
- Connectors Speaker Output: 2 x Speakon compatible, 2 x binding post
- Cooling System: Fan
- Power Supply: 230V / 50-60 Hz
- Dimensions (W x H x D): 483 x 88 x 298 mm
|
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 300 Watt rms | | Power output stereo 8Ω: | 2 x 180 Watt rms | | Power output bridged 8Ω: | 600 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 6 A | | Power Consumption: | 1300 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 470 / 18.05 mm/inch | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
VLP Series Powere Amplifier
Output Power: 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD (Bridge Mode, Mono) 600W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 33 lbs. / 15 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter
|
- 2Χ350W 8Ω 2x500W 4Ω 2x650W STEREO MODE
- BRIDGE 2000W 4 Ω
- 16Kg
- 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
- Precise Power, Signal and Clip LEDs to monitor performance
- XLR and 1/4" TRS input connectors for compatibility with any source
- Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
- Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
- Independent limiters per channel offer reliable protection against overload and distortion
- High-current toroidal transformer for ultra-high transient response and absolute reliability
- Ultra-reliable Toshiba/Fairchild power transistors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front” ventilation system including air filter for reliable operation
- “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
| The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Frequency response
20 - 20000 Hz
Signal-to-noise ratio
105 dB
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Features
Volex mains socket
|
InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz
high pass filter 30Ηz & 50Ηz
|
Reviews
There are no reviews yet.