Content | The ideal accessory for the industry leading DR-10L Bodypack Digital Recorder, the TM-10LB is a replacement lavalier microphone that not only privides a backup for critical recoding jobs but also allows the recordist to select between a white and black microphone element.
The TM-10LB and TM-10LW also feature a Sennheiser style screw lock connector maing them an attractive acccessory to many Sennheiser based audio rigs
Matching Lapel Clip and Windscreen Included
Ensuring a clean, crisp look as well as excellent audio performance in a variety of locations, both the TM-10LB and the TM-10LW come complete with a color matched lapel clip and windscreen.
Features at-a-glance
- Secure connection with screw-down connector
- Sennheiser style connector features 1/8” (3.5mm) male jack with screw-down plug for firm connection with wireless transmitters or TASCAM DR-10 series. (Connection with normal 3.5mm jack is also available)
- Windscreen and clip included
- Color variation - black (TM-10LB) or white (TM-10LW)
- Microphone sensitivity: -42dBV/PA, maximum SPL: 115dB SPL
- Omnidirectional lavalier microphone
- Cable length: 160cm
Model |
Back-electret condenser microphone |
Directivity |
Omnidirectional |
Frequency response |
50Hz - 18,000Hz |
Output impedance |
1.8k ohm (at 1kHz) |
Load impedance |
100Ω |
Sensitivity |
-42dB (0dB=1V/Pa at 1kHz) |
Max. SPL |
115dB SPL (at 1kHz) |
Connector |
3.5mm (1/8“) stereo mini plug (with screw lock) |
Power |
Plug-in power |
Drive voltage |
1.5 - 10v |
Dimensions |
132.5 × 457.5 × 140 mm / 5.2 x 18 x 5.5 inch |
Weight |
24g (0.053 lb) |
|
Type Condenser - Omni
Frequency Ressponse 60Hz - 18kHz
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Resistance 3000Ω
Dimensions 4.50mmW x 12.00mmH x 4.50mmD
Weight 1.00gm
Accessories Αntitrauma case,WS-LAV, Minifur LAV, Micon cable, Spanner |
Transducer Electret condenser
Polar Pattern Cardioid
Frequency Response 20 to 20,000Hz
Output Impedance 165.5 Ω
Sensitivity -39.0 dBV/Pa (11.0 mV)
Max Input Sound Level (SPL) 1000 Ω load: 129.5 dB SPL; 2500 Ω load: 134.5 dB SPL
Signal-to-Noise Ratio 57.0 dB
Dynamic Range @1kHz
1000 Ω: 92.5 dB SPL; 2500 Ω: 97.5 dB SPL
Self Noise 37.0 dB
(equivalent SPL, A-weighted, typical)
Clipping Level 1000 Ω load: 1.0 dBv; 2500 Ω load: -4.5 dBv
Operating Temperature Operating: 0 to 135°F (-18 to 57°C)
Storage: -20 to 165°F (-29 to 74°C)
Polarity XLR: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Power Requirements 11-52VDC phantom power (IEC-61938),
Dimensions (LxDiameter) Length: 5' (1.52m)
Diameter: 0.23" (5.8mm)
Weight 4.3 oz (121 g)
| Subminiature lavalier design; ideal size for theater, television, broadcasting, video, film, and sound reinforcement
Small, inconspicuous mounting hardware
Full, clear sound comparable to larger microphones
Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
Controlled low-frequency rolloff reduces low-frequency clothing and room noise
Low distortion, wide dynamic range
Uniform omnidirectional polar pattern
Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
Wide-range phantom powering (SM93) accepts all commonly used voltages
Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz
Response Curve Image Small SM93 WL93 View Larger
Polar Pattern
Omnidirectional, uniform with frequency
Output Impedance
3000 ohms
Output Level (1 Pascal = 94 dB SPL)
Open Circuit Voltage: -38 dBV/Pa (13 mV)
Output Clipping Level (at 1,000 Hz)
0.25 V at 120 dB
Total Harmonic Distortion
Less than 1% at 120 dB
Maximum SPL
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL)
18 dB typical, A-weighted
Signal-to-Noise Ratio
76 dB at 94 dB SPL (IEC 651)
Polarity
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
*Produces positive voltage at pin 2 of Shure wireless receiver three-pin connector
Recommended Operating Voltage
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
Current Drain
40 microA typical
Environmental Conditions
Operating Temperatures: -18 to 57 degrees C (0 to 135 degrees F)
Storage Temperatures: -29 to 74 degrees C (-20 to 165 degrees F)
Cable
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type TA4F (WL93T: Tan 1.27 m [4.17 ft])
Case
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Net Weight
Microphone: 16 g (0.57 oz) |
Lavaliere Microphone for WS 100 BP Belt Pack and for WS 1616 BP Belt Pack - Uni-directional Electret Condenser Lavaliere Microphone
- Impedance
- Frequency range : 20 Hz – 20 KHz
- Sensitivity : -44 ± 2 dB (at 1 KHz)
Product type
Wireless Microphone System Accessories
Type
Microphones
Frequency response
20 - 20.000 Hz
Directivity
cardioid
Nominal impedance
680 Ohm(s)
Phantom power requierements
5 V
Microphone input
mini-XLR (3-pin, female)
Accessories (included)
attaching clip , Foam windscreen
Weight
0,04 kg
|
Shure WL-185 Lavalier Condenser Microphone
Models WL183, WL184 and WL185 are lavalier electret condenser mics designed for use
with a wireless body-pack transmitter. Each mic has a 1.2 meter (4 ft.) cable terminated
with a miniature 4-pin mini connector. Included tie clip can be rotated in 90 degree intervals for placement flexibility.
WL185 (Cardioid):
Recommended for general purpose sound reinforcement applications requiring good rejection of ambient noise.
Use of windscreen highly recommended. Pickup angle: 130 degrees.
Type
Condenser (electret bias)
Frequency Response
50 to 17,000 Hz
Output Impedance
1800 ohms
Sensitivity (1 Pa = 94 dB SPL)
WL183: -40.0 dBV/Pa
WL184: -44.5 dBV/Pa
WL185: -45.5 dBV/Pa
Maximum Sound Pressure Level
WL183: 125.0 dB SPL
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
Output Noise (A-weighted)
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
Dynamic Range
102.5 dB
Polarity
Positive pressure on diaphragm produces positive voltage on pins 3 and 4 relative to pin 1.
Power Requirements
Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) provided at microphone connector pin 2 relative to pin 1 of a Shure wireless microphone transmitter.
|
Reviews
There are no reviews yet.