| Content |
24-channel ADAT optical digital interface card for X-48 |
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
| TASCAM's award winning DR-60D is the new audio recording solution for on-set filmmakers and videographers using DSLR's. For years, filmmakersProSound Network Best of Show have been trying different methods for recording audio, using bulky recorders designed for music and trying to transform the inferior audio technology built-into DSLR's. Now TASCAM has designed an answer that pros and amateurs alike have been waiting for.
The DR-60D is a brand new 4-track solid-state recorder utilizing TASCAM's decades of experience. The recorder utilizes high-grade HDDA pre-amps, legendary AD converters, and a durable but lightweight structure and shape. This device will fit snuggly under any camera or into any rig, and record up to 96kHz/24-bit high quality audio straight to SD/SDHC media. Filmmakers have at their disposal two 1/4“-XLR Locking Combo MIC/LINE Inputs, 3.5mm Stereo MIC Input, Camera In, Camera Out, Line Out and Headphone Out. Both 1/4“-XLR Combo Inputs supply +48V Phantom Power and the 3.5mm Input supplies Plug-In Power for microphones requiring a bias voltage.
The DR-60D is incredibly easy to use, employing TASCAM's very popular user interface and external controls for every major operation. The body structure, soft-touch keys and dials are designed specifically to help eliminate handling noise. The multiple record modes include, 4-Channel Record, Auto Record and TASCAM's Dual Record "Safety Track" Mode make the DR-60D one of the most versatile recorders on the market.
- Record to SD/SDHC card (Up to 32GB)
- Simultaneously record up to 4 tracks
- Record Mode：MONO, STEREO, DUAL MONO, DUAL STEREO, 4-CHANNEL
- Recording format：44.1/48/96kHz 16/24bit (WAV/BWF)
- TASCAM original HDDA microphone preamps
- Recording levels can be adjusted independently for the 1/L, 2/R and 3-4 inputs
- Two XLR/TRS inputs support +4dBu line level input and phantom power (24 or 48VDC on XLRF)
- Plug-in power and high-output mic input supported on inputs 3-4
- CAMERA OUT connector for output from the DR-60D's mixer (adjustable gain)
- CAMERA IN connector for sound monitoring from the camera
- Independent adjustable LINE OUT and HEADPHONE jacks for high-quality sound output
- 50mW/ch headphone output
- Tripod mounting socket (bottom) and DSLR mounting screw attachment (top)
- Handles protect the screen and can be used to attach a shoulder strap
- Soft-Touch Rubber Keys for silent operation
- HOLD switch to prevent accidental operation
- QUICK button feature for easy access to various functions
- 128x64 pixel LCD with backlight
- USB 2.0 connection for high-speed transferring of files
- Mini USB cable included
- Operates on 4-AA batteries, an AC adapter (sold separately) or USB bus power
- Can extend battery life with BP-6AA battery pack (sold separately)
- Dedicated remote control jack for the wired RC-10 remote control or RC-3F footswitch (both sold separately)
- Internal mixer: PAN and LEVEL controls
- Low cut filter(40/80/120Hz)
- Limiter (1/L and 2/R can be selected for link-operation)
- Delay function for microphone distance adjustment (up to 150ms)
- M-S decode function
- Slate tone generator (AUTO/MANUAL)
- Selectable duration of slate tone from four positions (0.5/1/2/3 sec, when auto-generated)
- Selectable slate tone generation. 3 positions: OFF/HEAD/HEAD+TAIL, when auto-generated
- File name format can be set to use a user-defined word or date
- Dual-recording function allows two files to be recorded simultaneously at different levels
- Auto-record function can automatically start and stop recording at set level
- Pre-recording function allows the unit to record a 2 second sound buffer before recording is activated
- Self-timer function for solo recording
- New file starts recording automatically without interruption when maximum file size is reached
- Track incrementing function allows a recording to be split by creating a new file when desired
- Jump back and play function
- Equalizer function for playback, and level alignment function to enhance the perceived overall sound pressure
- Resume function to memorize the playback position before the unit is turned off
- MARK function up to 99 points per audio track
- DIVIDE function
SPECIFICATIONS
| Recording media |
SD card(64MB to 2GB), SDHC card(4GB to 32GB) |
| Recording format |
|
| WAV |
44.1/48/96kHz, 16/24bit |
| BWF |
44.1/48/96kHz, 16/24bit |
| Number of channels |
4channel (stereo x2) |
| Analog audio input |
|
| 1/L, 2/R connectors |
|
| Connector |
XLR-3-31 (1:GND, 2:HOT, 3:COLD)/6.3mm(1/4“)TRS standard jack |
| Set to "MIC / MIC+PHANTOM“ |
|
| Input impedance |
2k ohms |
| Phantom power |
48V +/-4V(10mA/CH) / 24V +/-4V(10mA/CH) |
| Maximum input level |
0dBu |
| Minimum input level |
-72dBu |
| MIC input gain |
TRIM MAX |
| LOW |
+11dB |
| MID |
+36dB |
| HIGH |
+52dB |
| Set to "LINE“ |
|
| Input impedance |
10k ohms or more |
| Standard input level |
+4dBu |
| Maximum input level |
+24dBu |
| 3-4 connector |
|
| Connector |
3.5mm (1/8“) stereo mini jack (this connector can be supplied plug-in power) |
| Input impedance |
10k ohms |
| Maximum input level |
+10dBV |
| Minimum input level |
-50dBV |
| MIC input gain |
TRIM MAX |
| LOW |
+3dB |
| HIGH |
+26dB |
| CAMERA IN connector |
|
| Connector |
3.5mm (1/8“) stereo mini jack |
| Input impedance |
10k ohms |
| Standard input level |
-10dBV |
| Maximum input level |
+6dBV |
| Analog audio output |
|
| CAMERA OUT connector |
|
| Connector |
3.5mm (1/8“) stereo mini jack |
| Output impedance |
200 ohms |
| Standard output level |
-50dBV |
| Maximum output level |
-30dBV |
| LINE OUT connector |
|
| Connector |
3.5mm (1/8“) stereo mini jack |
| Output impedance |
200 ohms |
| Standard output level |
-10dBV |
| Maximum output level |
+10dBV |
| PHONES connector |
|
| Connector |
3.5mm (1/8“) stereo mini jack |
| Maximum output level |
50mW + 50mW |
| USB |
|
| Connector |
Mini-B type |
| Format |
USB2.0 HIGH SPEED mass storage class |
| REMOTE |
|
| Connector |
2.5mm TRS jack |
| Power |
Four AA batteries(Alkaline or NI-MH),
USB bus power,
Dedicated AC adapter(TASCAM PS-P515U, sold separately),
Dedicated external battery pack(TASCAM BP-6AA, sold separately) |
| Power consumption |
5.4W |
| Continuous operation time |
2ch WAV, 44.1kHz, 16bit rec |
| DR-60D |
|
| Alkaline batteries (EVOLTA) |
About 2:30 min (Phantom on)
About 4:30 min (Phantom off) |
| NI-MH batteries (eneloop) |
About 3:15 min (Phantom on)
About 5:00 min (Phantom off) |
| NI-MH batteries (eneloop pro) |
About 3:45 min (Phantom on)
About 6:00 min (Phantom off) |
| DR-60D+BP-6AA |
|
| Alkaline batteries (EVOLTA) |
About 5:30 min (Phantom on)
About 10:30 min (Phantom off) |
| NI-MH batteries (eneloop) |
About 7:30 min (Phantom on)
About 12:00 min (Phantom off) |
| NI-MH batteries (eneloop pro) |
About 9:30 min (Phantom on)
About 14:30 min (Phantom off) |
| Dimensions |
133(W)×93.2(H)×78(D)mm (with the top adapter attached) |
| Weight |
510g (not including batteries) |
| Operating temperature |
0˚C to 40˚C |
| Standard accessories |
USB cable, warranty card, Owner's manual |
| Computer compatibility |
| Windows |
| OS |
Windows XP, Windows Vista, Windows 7, Windows 8 |
| CPU |
Pentium 300MHz or more |
| RAM |
128MB or more |
| USB |
recommended: USB2.0 |
| Macintosh |
| OS |
Mac OS X Jaguar (V10.2), Mac OS X Panther (V10.3), Mac OS X Tiger (V10.4),
Mac OS X Leopard (V10.5), Mac OS X Snow Leopard(V10.6.8), OS X Lion(V10.7),
OS X Mountain Lion(V10.8) |
| CPU |
Power PC, iMac, G3, G4 266MHz or more |
|
64MB or more |
| USB |
recommended: USB2.0 |
| Audio performance |
| Frequency response |
20-20kHz +0.5/-2dB(LINE IN or MIC IN to LINE OUT, Fs44.1k/48kHz, JEITA)
20-40kHz +0.5/-3dB(LINE IN or MIC IN to LINE OUT, Fs96kHz, JEITA) |
| Distortion |
0.02% or less(LINE IN or MIC IN to LINE OUT Fs44.1k/48k/96kHz, JEITA) |
| S/N ratio |
92dB or more(LINE IN or MIC IN to LINE OUT Fs44.1k/48k/96kHz, JEITA) |
| Equivalent input noise |
-120dBu or more |
Recording duration
The table below shows the maximum recording time on SD/SDHC cards of different capacities for different file formats for recording.
| File format(recording setting) |
SD/SDHC card capacity(hours:mintes) |
| 1GB |
2GB |
4GB |
8GB |
| WAV/BWF 16bit(STEREO) |
44.1kHz |
1:41 |
3:22 |
6:44 |
13:28 |
| 48kHz |
1:33 |
3:06 |
6:12 |
12:24 |
| 96kHz |
0:46 |
1:33 |
3:06 |
6:12 |
| WAV/BWF 24bit(STEREO) |
44.1kHz |
1:07 |
2:15 |
4:30 |
9:00 |
| 48kHz |
1:02 |
2:04 |
4:08 |
8:16 |
| 96kHz |
0:31 |
1:02 |
2:04 |
4:08 |
- The recording times shown above are estimates. They might differ depending on the SD/SDHC card in use.
- The recording times shown above are not continuous recording times, but rather they are the total possible recording times for the SD/SDHC card.
- If recorded in mono in WAV files, the maximum recording time will be double the figures above.
- For dual and 4-channel recording in WAV/BWF format, the recording times are about half those shown above.
|
Main Features
* Colour TFT touch screen interface
* 20 illuminated flash start keys
* Up to 100 tracks available for flash start through touch screen
* Transport and Online buttons recessed to prevent accidental operation
* 100-mm fader with fader start capability and 0-dB lock
* Monitor speaker and headphones output for monitoring
* CAT6 connection to HS-2 and HS-8
|
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
* 0 dB = 0.775 V | Power Source | 220 - 240 V AC | | Power Consumption | 18 W | | Volume Adjustment | 100 mm motorized fader x 12
Rotary encoder x 8 | | Line Input | 1 channel (stereo) | | Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) | | Monitor Bus | 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) | | LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) | | Control | RS-232C: D-sub connector (9 pins) for maintenance use | | Finish | Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate | | Dimensions | 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43) | | Weight | 6.6 kg (14.55 lb) | | Accessory | Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3 | | Option | Console case: D-2012AS |
|
The KORE 64™ ROM option represents a complete expansion and reimagining of the PC3 and PC3K's sonic potential (not for the PC3LE). Pushing the limits of V.A.S.T. synthesis for both realistic and experimental electronic sounds, KORE 64™ adds over 300 new programs, including stunning new Synths, Electric Guitars, Horns, Drums and Percussion. With KORE 64™ installed, the PC3/K built-in program library now totals over 1400 presets!
New Setups:
50 new setups featuring the KORE 64™ sounds.
Over 200 new drum grooves in multiple styles.
New Dance and Hip Hop setups for triggering and controlling beats in real time.
New Synths:
New samples modeled after the Oberheim SEM, ARP Chroma, TX802, CZ1, and dozens of legacy waveforms from the K series.
Over 100 new synth programs.
Sounds for popular electronic music styles like House, Trance, Dubstep, Drum&Bass, Glitch, Electro Hip Hop, and more.
More real time controls, beat-synced modulations and envelope control transform sounds without hitting the edit button.
Atmospheric and cycling pads voiced for performing, producing, and scoring.
New Guitars:
New samples modeled after the Gibson Les Paul and Fender Stratocaster.
Palm muted and sustained articulations playable in a picked or legato style.
Instant-shredder arpeggiator patterns, whammy bar effects, and realistic feedback emulations.
Preset sounds from Rock, Country, Rock-a-Billy, Metal, Funk, and more.
New Brass/Woodwinds:
New alto sax, tenor sax, baritone sax, trumpet, and trombone samples.
New programs include solo instruments and custom sections with many combinations of the different instruments.
Articulate with pressure on several new programs.
Sections cover styles from Big Band, Soul, Funk, Latin, R&B, Hip Hop, Rock and more.
New Drums
Drums from Yamaha, Ludwig, Pearl, DW, Rogers, and Gretsch recorded as full kits.
Full cymbal arrays recorded with Zildjian, Paiste, and Sabian cymbals.
72 new Drum Kits and 62 percussion instruments and templates.
10 times the samples and 30 times the data of the existing PC3/PC3K Drums.
All drum kits have mixer functioning on the sliders to change the level the kick, snare, toms, hats, and percussion independently.
Unsurpassed realism and playability for sampled drums.
Full complement of Electronic and Processed Drum samples.
Scratches, hits and Industrial Sounds.
Wide variety of traditional and processed Percussion sounds.
Download the full preset Objects List under the Downloads section
User Installable.
Requires: PC3K OS v2.20 or better
PC3 OS v2.20 or better
All specifications subject to change without notice.
|
Reviews
There are no reviews yet.