Content |
Adds eight balanced line inputs and outputs to the DM-3200 or DM-4800. It's a great solution for adding more wireless receivers and monitor outs in a live sound installation. Internal jumpers allow you to set the operating level to -11, -16dB or -20dBfs. Uses DB25 connector wired with "TASCAM standard" pinout. Also works with older TASCAM gear such as the DM-24, DS-M71 and SX-1. |
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
|
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
* 0 dB = 0.775 V Power Source | 220 - 240 V AC | Power Consumption | 18 W | Volume Adjustment | 100 mm motorized fader x 12
Rotary encoder x 8 | Line Input | 1 channel (stereo) | Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) | Monitor Bus | 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) | LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) | Control | RS-232C: D-sub connector (9 pins) for maintenance use | Finish | Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate | Dimensions | 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43) | Weight | 6.6 kg (14.55 lb) | Accessory | Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3 | Option | Console case: D-2012AS |
|
Liquid Mix HDLiquid Mix HD | TDM Plugin for Pro Tools HD
Key Features
Variety of Classic Emulations
40 compressors and 20 EQs, sampled from vintage originals with a free expanding library online.
Dynamic Convolution Technology
The unique patented Dynamic Convolution process delivers unparalleled EQ and Compression emulations.
Ultra-Low Latency for Recording
With the ultra-low latency of Liquid Mix HD (just 12 samples), it can now be used for recording and live sound applications
Optimised for Pro Tools HD
Over one hundred simultaneous mono instances can be run at 44.1/48kHz on an HD3 system.
Full Control Surface Mapping
Pro Tools TDM format ensures full control mapping on all major Pro Tools control surfaces, including ICON and VENUE.
Unique Hybrid Super EQ
Create your own totally unique 7-band super EQ, built out of separate classic EQ bands.
Compressor 'Free' Mode
Vintage compressors with limited controls can now be set to provide fully variable Attack, Release and Ratio.
Automation and Full Recall
Perfect integration with Pro Tools HD allows for automation of parameters and full recall within your session.
| Tuner + Metronome + Recorder - All in One Unit!
The TMR-50 - Your Ideal Practice Partner
Highlights:
- Tuner, metronome, and recorder can be used simultaneously or independently.
- Internal mic and speaker make it easy to record and play back your performance
- Loop Play function lets you repeat a desired region of a recorded track
- High-quality linear PCM recording/playback
- Record up to 100 tracks (approximately total 20 minutes)
- USB port lets you transfer recorded data and song files between the TMR-50 and your computer
- Newly designed highly responsive LCD needle-type meter
- Wide detection range from C1 to C8
- The Sound Out function produces a reference tone in a three-octave range from the built-in speaker
- The Sound Back function generates the reference tone that's closest to the input sound, while the meter indicates the pitch discrepancy between the reference and the input sound - a great function for ear training!
- Calibration supports a range of concert pitches
- Marks indicate pure major and minor third intervals
- Wide tempo range of 30--252 beats per minute
- 15 rhythm variations let you practice with a broad range of musical styles
- Easy tempo settings with two types of tempo step patterns plus a tap tempo function
- Large LCD with backlight brightness that's adjustable over two levels for enhanced visibility
- Your choice of body color: black or pearl white
- Convenient key layout, and newly designed stand and battery cover
- Memory Backup and Auto Power Off
Korg's popular TM series of tuner/metronome units is loved by players who practice to perfect their musical skills. Now joining the lineup is the TMR-50, which adds recorder functionality to the already impressive list of features. An extremely valuable way to improve your playing ability is to identify the problem areas that need work, and then practice to improve those areas. With its built-in mic and speaker, the TMR-50 makes it easy to practice this way. It provides high-quality linear PCM recording and a USB port for convenient usage with your computer. The TMR-50 features equally robust capabilities for its tuner and metronome functionality that will help you improve your sense of pitch and rhythm. Two choices of color are available: black and pearl white. Whether you're in a brass band or an orchestra, the TMR-50 is the ideal partner for anyone who wants to improve their playing.
Specifications
Recording format:
PCM audio format, WAV format (extension: .wav) 44.1 kHz@16-bit
Available recording time:
Maximum approx. 20 minutes (Internal Memory size is 120 MB)
Total number of tracks:
Up to 100 tracks
Tuning:
12 note equal temperament
Detection range:
C1 (32.70 Hz) ~ C8 (4186 Hz), Using Sine Wave.
Reference tone:
C3 (130.81 Hz) ~ C6 (1046.50Hz), 3 Octave.
Tuning Mode:
Meter Mode (AUTO), Sound Out Mode (MANUAL), Sound Back Mode (AUTO)
Calibration range:
A4 = 410 ~ 480 Hz (1 Hz steps)
Detection accuracy:
+/- 1 cent
Sound precision:
+/-1 cent
Tempo range:
Quarter Note = 30 to 252 BPM
Tempo setting:
3 Types: Pendulum Step
Full Step
Tap Tempo
Beat range:
Total 10 beats: "0 to 9" as "Quarter-note" Rhythm
Rhythm pattern:
Duplets, triplets, triplets without the center beat, quadruplets, and quadruplets without the center beats
Tempo accuracy:
±0.3%
Terminals:
Input (f6.3mm, Mono-Standard Jack type)
Headphones (f3.5mm, Stereo-mini Jack type)
USB (mini-Type B)
Internal Speaker:
Dynamic Speaker (f28 mm)
Power (Battery):
AAA battery (3.0 V) x 2
Manganese batteries or alkaline batteries, Ni-MH: Nickel metal hydride
Battery Life:
Recorder ... Approximately 16/13/11 hours
(Backlight: off/soft/auto, using alkaline batteries. Maximum of 20 minutes per
recording.)
Tuner ... Approximately 24/22/20 hours
(Backlight: off/soft/auto, A4 continuous input, using alkaline batteries)
Metronome ... Approximately 18/16/14 hours
(Backlight: off/soft/auto, tempo 120, 4 beats, maximum volume, using alkaline batteries)
Dimensions (W x D x H):
111 x 82 x 18 mm / 4/37 x 3.23 x 0.71 inches
Weight:
119 g / 4.19 oz (Including battery)
Included items:
AAA battery (3.0 V) x 2 for verifying proper operation
USB Cable
Options:
Contact Mic = CM-100L
Computer Requirements
Windows:
A computer that satisfies the operating requirements of Microsoft Windows XP/Windows Vista/Windows 7 and is equipped with a USB port
Macintosh:
Mac OS X 10.5 or later |
The Apogee X-VID-SYC-GEN Video Expansion Card is designed to fit in the X-Series card slot located in the rear panel of the Apogee Big Ben Master Digital Clock (sold separately). Allows all functions to be controlled from the Big Ben user interface and generates video and provides genlocking function. In genlocking mode the source video-signal will be re-clocked and regenerated, maintaining the same
field and colorburst phase information, but stripped of its line information and replaced by video-black. In slave mode the board will auto-detect the incoming video-standard and configure itself accordingly. The video input is of very high tolerance and will even lock to unstable sources like VCR's.
The Apogee X-VID-SYC-GEN Video Expansion Board has three modes of operation.
•Master mode: The user selects the video format on the frontpanel of the Big Ben. The Big Ben will slave to the generated video signal
•Attended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben will slave to the incoming video signal
•Unattended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben is not clocking to the Video board and therefore both will function independently
Features - Support for PAL, NTSC and 60 Hz B&W standards
- One composite video input and three composite video outputs
- Can operate as a master black-burst generator
- Can operate as genlocking slave device
|
Reviews
There are no reviews yet.