Content |
For users of just about any TASCAM multitrack, the RC-30P is a wonderful timesaver. Punching in on recordings by hand means you're not ready to play right away. The RC-30P lets you play straight through. While automated punch-ins available on some recorders are also helpful, most punches can be done with the simple and efficient precision of the RC-30P, saving you time.
|
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
| Tuner + Metronome + Recorder - All in One Unit!
The TMR-50 - Your Ideal Practice Partner
Highlights:
- Tuner, metronome, and recorder can be used simultaneously or independently.
- Internal mic and speaker make it easy to record and play back your performance
- Loop Play function lets you repeat a desired region of a recorded track
- High-quality linear PCM recording/playback
- Record up to 100 tracks (approximately total 20 minutes)
- USB port lets you transfer recorded data and song files between the TMR-50 and your computer
- Newly designed highly responsive LCD needle-type meter
- Wide detection range from C1 to C8
- The Sound Out function produces a reference tone in a three-octave range from the built-in speaker
- The Sound Back function generates the reference tone that's closest to the input sound, while the meter indicates the pitch discrepancy between the reference and the input sound - a great function for ear training!
- Calibration supports a range of concert pitches
- Marks indicate pure major and minor third intervals
- Wide tempo range of 30--252 beats per minute
- 15 rhythm variations let you practice with a broad range of musical styles
- Easy tempo settings with two types of tempo step patterns plus a tap tempo function
- Large LCD with backlight brightness that's adjustable over two levels for enhanced visibility
- Your choice of body color: black or pearl white
- Convenient key layout, and newly designed stand and battery cover
- Memory Backup and Auto Power Off
Korg's popular TM series of tuner/metronome units is loved by players who practice to perfect their musical skills. Now joining the lineup is the TMR-50, which adds recorder functionality to the already impressive list of features. An extremely valuable way to improve your playing ability is to identify the problem areas that need work, and then practice to improve those areas. With its built-in mic and speaker, the TMR-50 makes it easy to practice this way. It provides high-quality linear PCM recording and a USB port for convenient usage with your computer. The TMR-50 features equally robust capabilities for its tuner and metronome functionality that will help you improve your sense of pitch and rhythm. Two choices of color are available: black and pearl white. Whether you're in a brass band or an orchestra, the TMR-50 is the ideal partner for anyone who wants to improve their playing.
Specifications
Recording format:
PCM audio format, WAV format (extension: .wav) 44.1 kHz@16-bit
Available recording time:
Maximum approx. 20 minutes (Internal Memory size is 120 MB)
Total number of tracks:
Up to 100 tracks
Tuning:
12 note equal temperament
Detection range:
C1 (32.70 Hz) ~ C8 (4186 Hz), Using Sine Wave.
Reference tone:
C3 (130.81 Hz) ~ C6 (1046.50Hz), 3 Octave.
Tuning Mode:
Meter Mode (AUTO), Sound Out Mode (MANUAL), Sound Back Mode (AUTO)
Calibration range:
A4 = 410 ~ 480 Hz (1 Hz steps)
Detection accuracy:
+/- 1 cent
Sound precision:
+/-1 cent
Tempo range:
Quarter Note = 30 to 252 BPM
Tempo setting:
3 Types: Pendulum Step
Full Step
Tap Tempo
Beat range:
Total 10 beats: "0 to 9" as "Quarter-note" Rhythm
Rhythm pattern:
Duplets, triplets, triplets without the center beat, quadruplets, and quadruplets without the center beats
Tempo accuracy:
±0.3%
Terminals:
Input (f6.3mm, Mono-Standard Jack type)
Headphones (f3.5mm, Stereo-mini Jack type)
USB (mini-Type B)
Internal Speaker:
Dynamic Speaker (f28 mm)
Power (Battery):
AAA battery (3.0 V) x 2
Manganese batteries or alkaline batteries, Ni-MH: Nickel metal hydride
Battery Life:
Recorder ... Approximately 16/13/11 hours
(Backlight: off/soft/auto, using alkaline batteries. Maximum of 20 minutes per
recording.)
Tuner ... Approximately 24/22/20 hours
(Backlight: off/soft/auto, A4 continuous input, using alkaline batteries)
Metronome ... Approximately 18/16/14 hours
(Backlight: off/soft/auto, tempo 120, 4 beats, maximum volume, using alkaline batteries)
Dimensions (W x D x H):
111 x 82 x 18 mm / 4/37 x 3.23 x 0.71 inches
Weight:
119 g / 4.19 oz (Including battery)
Included items:
AAA battery (3.0 V) x 2 for verifying proper operation
USB Cable
Options:
Contact Mic = CM-100L
Computer Requirements
Windows:
A computer that satisfies the operating requirements of Microsoft Windows XP/Windows Vista/Windows 7 and is equipped with a USB port
Macintosh:
Mac OS X 10.5 or later | Specifications:
- Recording media: SD card(64MB to 2GB), SDHC card(4GB to 32GB), SDXC card(48GB to 128GB)
- Recording format
• WAV: 44.1k / 48k / 96k Hz, 16bit / 24bit
• BWF: 44.1k / 48k / 96k Hz, 16bit / 24bit
- Number of channels: 4-channel (stereo × 2, mono × 4)
- Analog audio input
• Connector: XLR-3-31 (1:GND, 2:HOT, 3:COLD) / 6.3mm(1/4“)TRS standard jack
Set to "MIC / MIC+PHANTOM“
• Input impedance: 2k ohms
• Phantom power: 48V +/-4V(10mA/CH), 24V +/-4V(10mA/CH)
• Maximum input level: 0dBu
• Minimum input level: -72dBu
• MIC input gain: TRIM MAX
• LOW: +11dB
• HIGH: +51dB
• HI + PLUS: +63dB
• Input impedance: 10k ohms or more
• Standard input level: +4dBu
• Maximum input level: +20dBu
• Connector: 3.5mm(1/8“)stereo mini jack (this connector can be supplied plug-in power)
• Input impedance: 10k ohms
• Maximum input level: +10dBV
• Minimum input level: -50dBV
• MIC input gain: TRIM MAX
• LOW: +3dB
• HIGH: +26dB
• HI + PLUS: +38dB
• Connector: 3.5mm(1/8“)stereo mini jack
• Input impedance: 10k ohms
• Standard input level: -10dBV
• Maximum input level: +6dBV
Analog audio output
• Connector: 3.5mm(1/8“)stereo mini jack
• Output impedance: 200 ohms
• Standard output level: -10dBV
• Maximum output level: +6dBV
• Connector: 3.5mm(1/8“)stereo mini jack
• Output impedance: 200 ohms
• Standard output level: -40dBV
• Maximum output level: -24dBV
• Connector: 3.5mm(1/8“)stereo mini jack
• Maximum output level: 20mW + 20mW
USB
• Connector: Micro-B type
• Format: USB2.0 HIGH SPEED mass storage class
- REMOTE Connector: 2.5mm TRS jack
- Power: 4 AA batteries(Alkaline or NI-MH), USB bus power, Dedicated AC adapter(TASCAM PS-P515U, sold separately), Dedicated external battery pack(TASCAM BP-6AA, sold separately)
- Power consumption: 5.0W
- Continuous operation time: 2ch WAV, 44.1kHz, 16bit rec, Phantom power not used
- Dimensions: 169(W)×55.2(H)×106.5(D)mm (with the top adapter attached)
- Weight: 625g ( including batteries) / 530g (without batteries )
|
Specifications General | Recording media | | CompactFlash (CF) card | File system | | FAT32 | Recording format | | BWF (Monophonic, Polyphonic) | Number of channels | | 8 channels (44.1/48/88.2/96 kHz) 8 channels + stereo mix (44.1/48 kHz) 4 channels (176.4/192 kHz) | Quantization bit rate | | 16/24 bit | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | Reference clock | | Internal, Word In, Video In, Digital In (AES 1-8 IN, AES A-BIN, ADAT 1-8 IN) | Type of timecode frame | | 23.976, 24, 25, 29.97DF, 29.97NDF, 30DF, 30NDF | Limiter | | Attack time: 3 ms Release time: 300 ms Threshold: –5 dBFS Ratio: 32:1 | Analogue audio inputs and outputs | The error for nominal and maximum levels is ±1dB for all input and output jacks except the PHONES jack. | ANALOG INPUT (1-8) | | D-sub 25-pin | Input impedance | | 10 kOhm | Nominal input level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG INPUT (L/A, R/B) | | XLR-3-31 (1: GND, 2: HOT, 3: COLD) | Input impedance | | 10 kOhm | Nominal input level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG OUTPUT (1-8) | | D-sub, 25-pin | Output impedance | | 100 Ohm | Nominal output level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | ANALOG OUTPUT (A/B) | | XLR-3-32 (1: GND, 2: HOT, 3: COLD) | Output impedance | | 100 Ohm | Nominal output level | | When reference level is –9 dB: +6 dBu (1.55 Vrms) When reference level is not –9 dB: +4 dBu (1.23 Vrms) | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | PHONES connector | | 6.3-mm standard stereo jack | Maximum output power | | 45 mW + 45 mW or more (THD+N 0.1 % or less, into 32 Ohm) | Digital audio inputs and outputs | DIGITAL IN/OUT (AES/EBU) | | D-sub, 25-pin | Minimum input voltage | | 2 Vpp | Maximum input voltage | | 7 Vpp | Output voltage | | 2–5 Vpp | Format | | AES3-2003/IEC 60958-4 (AES/EBU) | DIGITAL I/O (ADAT) | | ADAT optical | Format | | ADAT | DIGITAL INPUT A-B | | XLR-3-31 | Input voltage | | 2–7 Vpp at 110 Ohm | Format | | AES3-2003 (AES/EBU) | DIGITAL OUTPUT L-R | | XLR-3-32 | Output voltage | | 2–5 Vpp at 110 Ohm | Format | | AES3-2003 (AES/EBU) | Other inputs and outputs | RS-422 | | D-sub, 9-pin | RS-232C | | D-sub, 9-pin | PARALLEL | | D-sub, 25-pin | CASCADE IN | | BNC | Input voltage | | TTL equivalent (5 V) | Input impedance | | 75 Ohm ±10 % Allowable frequency deviation of external synchronization: ± 100 ppm | CASCADE OUT | | BNC | Output voltage | | TTL equivalent (5 V) | Output impedance | | 75 Ohm ±10 % | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | TIME CODE IN | | BNC | Input voltage | | 0.5–5 Vpp | Input impedance | | 20 kOhm | TIME CODE OUT | | BNC | Output voltage | | 2–5 Vpp | Output impedance | | 600 Ohm ±10 | WORD/VIDEO IN | | BNC | Input voltage | | TTL equivalent (5 V) | Input impedance | | 75 Ohm ±10 % Allowable frequency deviation of external synchronization: ± 100 ppm | WORD/VIDEO THRU/OUT | | BNC OUT/THRU switch included (OUT is for WORD OUT only) | Output voltage | | TTL equivalent (5 V) | Output impedance | | 75 Ohm ±10 % | Sampling frequency (when using WORD) | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | ETHERNET | | RJ45 | Keyboard | | Mini-DIN (PS/2) | USB | | USB A-type, 4-pin | Protocol | | USB2.0 HIGH SPEED (480 Mbit/s) | Audio performance (analogue input to analogue outp | Frequency response | | | 20 Hz - 20 kHz | | ±0,5 dB (all sampling rates) | at 40 kHz | | +0,5 dB/–2 dB (Fs = 88.2/96 kHz) | at 80 kHz | | +0,5 dB/–5 dB (Fs = 176.4/192 kHz) | Distortion | | ≤0.005% (Reference level: –20 dB, input level: +23 dBu, 1 kHz, AES-17LPF) | S/N ratio | | ≥100 dB(A) (22 kHz LPF) | Power requirements and other specifications | Power requirements | | 100–240 V AC, 50–60 Hz | Power consumption | | 26 W | Dimensions (W x H x D) | | 483 mm x 88 mm x 288 mm | Weight | | 4.8 kg | Operating temperature range | | 5–35 °C |
|
Tuner + Metronome + Recorder - All in One Unit!
The TMR-50 - Your Ideal Practice Partner
Highlights:
- Tuner, metronome, and recorder can be used simultaneously or independently.
- Internal mic and speaker make it easy to record and play back your performance
- Loop Play function lets you repeat a desired region of a recorded track
- High-quality linear PCM recording/playback
- Record up to 100 tracks (approximately total 20 minutes)
- USB port lets you transfer recorded data and song files between the TMR-50 and your computer
- Newly designed highly responsive LCD needle-type meter
- Wide detection range from C1 to C8
- The Sound Out function produces a reference tone in a three-octave range from the built-in speaker
- The Sound Back function generates the reference tone that's closest to the input sound, while the meter indicates the pitch discrepancy between the reference and the input sound - a great function for ear training!
- Calibration supports a range of concert pitches
- Marks indicate pure major and minor third intervals
- Wide tempo range of 30--252 beats per minute
- 15 rhythm variations let you practice with a broad range of musical styles
- Easy tempo settings with two types of tempo step patterns plus a tap tempo function
- Large LCD with backlight brightness that's adjustable over two levels for enhanced visibility
- Your choice of body color: black or pearl white
- Convenient key layout, and newly designed stand and battery cover
- Memory Backup and Auto Power Off
Korg's popular TM series of tuner/metronome units is loved by players who practice to perfect their musical skills. Now joining the lineup is the TMR-50, which adds recorder functionality to the already impressive list of features. An extremely valuable way to improve your playing ability is to identify the problem areas that need work, and then practice to improve those areas. With its built-in mic and speaker, the TMR-50 makes it easy to practice this way. It provides high-quality linear PCM recording and a USB port for convenient usage with your computer. The TMR-50 features equally robust capabilities for its tuner and metronome functionality that will help you improve your sense of pitch and rhythm. Two choices of color are available: black and pearl white. Whether you're in a brass band or an orchestra, the TMR-50 is the ideal partner for anyone who wants to improve their playing.
Specifications
Recording format:
PCM audio format, WAV format (extension: .wav) 44.1 kHz@16-bit
Available recording time:
Maximum approx. 20 minutes (Internal Memory size is 120 MB)
Total number of tracks:
Up to 100 tracks
Tuning:
12 note equal temperament
Detection range:
C1 (32.70 Hz) ~ C8 (4186 Hz), Using Sine Wave.
Reference tone:
C3 (130.81 Hz) ~ C6 (1046.50Hz), 3 Octave.
Tuning Mode:
Meter Mode (AUTO), Sound Out Mode (MANUAL), Sound Back Mode (AUTO)
Calibration range:
A4 = 410 ~ 480 Hz (1 Hz steps)
Detection accuracy:
+/- 1 cent
Sound precision:
+/-1 cent
Tempo range:
Quarter Note = 30 to 252 BPM
Tempo setting:
3 Types: Pendulum Step
Full Step
Tap Tempo
Beat range:
Total 10 beats: "0 to 9" as "Quarter-note" Rhythm
Rhythm pattern:
Duplets, triplets, triplets without the center beat, quadruplets, and quadruplets without the center beats
Tempo accuracy:
±0.3%
Terminals:
Input (f6.3mm, Mono-Standard Jack type)
Headphones (f3.5mm, Stereo-mini Jack type)
USB (mini-Type B)
Internal Speaker:
Dynamic Speaker (f28 mm)
Power (Battery):
AAA battery (3.0 V) x 2
Manganese batteries or alkaline batteries, Ni-MH: Nickel metal hydride
Battery Life:
Recorder ... Approximately 16/13/11 hours
(Backlight: off/soft/auto, using alkaline batteries. Maximum of 20 minutes per
recording.)
Tuner ... Approximately 24/22/20 hours
(Backlight: off/soft/auto, A4 continuous input, using alkaline batteries)
Metronome ... Approximately 18/16/14 hours
(Backlight: off/soft/auto, tempo 120, 4 beats, maximum volume, using alkaline batteries)
Dimensions (W x D x H):
111 x 82 x 18 mm / 4/37 x 3.23 x 0.71 inches
Weight:
119 g / 4.19 oz (Including battery)
Included items:
AAA battery (3.0 V) x 2 for verifying proper operation
USB Cable
Options:
Contact Mic = CM-100L
Computer Requirements
Windows:
A computer that satisfies the operating requirements of Microsoft Windows XP/Windows Vista/Windows 7 and is equipped with a USB port
Macintosh:
Mac OS X 10.5 or later
|
Reviews
There are no reviews yet.