| Content |
Features at a glance
- SD/SDHC/SDXC cards used as recording/playback media
- 6 balanced mic/line inputs (1-4: XLR/TRS combo jacks, 5-6: TRS jacks)
- 6 unbalanced outputs (RCA pin jacks)
- COAXIAL digital input and output (S/PDIF, AES/EBU)
- Recording/playback formats: BWF, WAV, MP3
- With BWF format, recording starting times can be stored in files
- 8-track recording at 96kHz/24-bit (BWF, WAV)
6 mic/line inputs and stereo mix recording or 6 mic/line input and digital stereo recording
- Record MP3 files at 96, 128, 192 and 320 kbps
- Record 4-channel MP3 files
From 4 mic/line inputs (XLR/TRS combo jacks) or 2 mic/line inputs and digital stereo inputs
- 2-track recording at 24-bit/192kHz (BWF, WAV)
From 2 mic/line inputs or digital stereo inputs
- Digital inputs and outputs support double speed 96 kHz and quad speed 192 kHz
- Sampling frequencies
44.1, 48, 96, 192 kHz (BWF, WAV) 44.1, 48 kHz (MP3)
- Quantization bit depth: 16/24-bit (BWF, WAV)
- 6 channels of TASCAM HDDA mic preamps for high audio quality with 48V phantom power
- Limiter and low-cut filter available on each mic/line input
- Built-in stereo monitoring mixer for headphone mix and/or recording
- Dual-recording function allows two files to be recorded simultaneously at different levels
- GANG function allows the input gain of multiple channels to be operated simultaneously
- Pre-recording function allows the capture of audio two seconds before recording is started
- Automatic-recording function can start and stop recording automatically in response to the input signal level (−48, −24, −12 or −6 dB)
- Even when multiple tracks are used, all recordings made at the same time can be managed as a single take/file
- Track incrementation allows a recording to be split by creating a new file at the desired point without interrupting recording
- Up to 1000 takes and 5000 files can be recorded on a single card
- Mark function can be used to move to specific points (up to 99 marks per take)
- Wheel can be used to change the playback position
- Repeat playback function
- Panel lock function to prevent misoperation
- Cascade function allows transport control of multiple DR-680MKII units using a master unit
- File name format can be set to use a user-defined word or the date
- High-speed transfer of files to a computer using USB 2.0
- 128×64-dot matrix display with backlight
- Built-in mono speaker with 500mW output
- Headphone output and level control (50mW+50mW/ 32ohm)
- Powered by 8 AA batteries or the included AC adapter
- USB cable and shoulder strap included
- Folding stand convenient for tabletop use
- CS-DR680 carrying case (sold separately)
- AR-DR680 case by Portabrace also available
| Add 8 more ADAT optical inputs and outputs to your DM-3200 or DM-4800. Also works with older TASCAM gear such as the DM-24, DS-M71 and SX-1.The DP-32 is a home recording Portastudio with 32 tracks based on solid-state technology. The unit is equipped with colour LCD and channel strip controls to make recording simple so the user can stay creative. Up to eight tracks can be recorded at a time on a standard SD/SDHC memory card through its XLR and 6.3-mm combo jacks. Input processing like compression and limiting, an internal send effect with reverb, delay and chorus, guitar amp simulation and multi-effects for use with the instrument-level input as well as an external effects send are available during recording.
For mixdown, the DP-32 offers 20 channel faders and 12 rotary controls for EQ, Pan and effects including reverb and chorus. During the mastering process, the material can be further optimized with EQ, compression and normalization. Once finished, songs can be written to CD with the built-in CD-RW drive or transferred to computer over USB to publish the songs on the Internet, for example.
Main Features
32-track digital Portastudio
8 mono tracks, 12 stereo tracks (can also be used as mono tracks)
Record up to 8 tracks at once with 44.1/48 kHz and 16/24-bit audio resolution
Simultaneous playback of all 32 tracks
Virtual tracks for alternate takes and undo
Dedicated stereo master track
Colour LC display and 12-encoder channel strip for simple operation
Built-in 40-channel mixer
Mix down your 32 playback tracks with eight input signals to the dedicated stereo master track
Use the Bounce function to set tracks free by mixing multiple tracks to a single mono or stereo track
Dedicated controls for EQ, pan and effect sends
Solid-state recording to SD Card media for better shock resistance and reliability compared to hard drive recording
8 balanced microphone inputs on balanced combo XLR/jack connectors
Switchable phantom power for 4 channels each
One input switchable to instrument level for direct recording of a guitar or bass
Unbalanced stereo output (RCA jacks)
Balanced stereo monitor output (6.3-mm TRS jacks)
Two unbalanced effect sends (6.3-mm TS jacks)
Stereo headphones output (6.3-mm TRS jack)
MIDI input and output for MMC, Control Change and MTC output
Footswitch input (2.5-mm mini jack) for Tascam RC-3F (optional accessory)
Input effects (Limiter, Compressor, Noise suppressor, Exciter)
Guitar effects (Amp simulator, Reverb, Compressor, Chorus, Flanger, Phase shifter)
Mixdown effects (Reverb, Delay, Stereo chorus)
Mastering effect (Single/Multi-band stereo compressor, EQ, Noise shaping)
Mark function (up to 99 location marks)
Built-in chromatic tuner and metronome
CD-RW drive for audio CD creation as well as file import and export
USB 2.0 port for data backup/restore and file transfer with a computer
Specifications
Recording media and file systems
Recording media SD card (512 MB to 2 GB)
SDHC card (4–32 GB)
File system SD card (512 MB to 2 GB): FAT16
SDHC card (4–32 GB): FAT32
Analogue audio inputs and outputs
MIC/LINE INPUTS A–H, XLR (balanced)
Connector XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance 2.4 kOhm
Nominal input level –14 dBu
Maximum input level +2 dBu
MIC/LINE INPUTS A–H, phone jack (balanced)
Connector 6.3-mm TRS phone jack
Input impedance >22 kOhm or 1 MOhm (INPUT H, when LINE-GUITAR switch is set to GUITAR)
Nominal input level +4 dBu
Maximum input level +20 dBu
STEREO OUT L/R connectors RCA pin jack
Nominal output level –10 dBV
Maximum output level +6 dBV
Output impedance 200 Ohm
EFFECT SENDS 1/2 connectors 6.3-mm TS phone jack
Nominal output level –10 dBV
Maximum output level +6 dBV
Output impedance 200 Ohm
MONITOR OUT L/R connectors 6.3-mm TRS phone jack
Nominal output level –2 dBu
Maximum output level +14 dBu
Output impedance 200 Ohm
PHONES connector 6.3-mm TRS phone jack
Maximum output power 70 mW + 70 mW or more (THD + N 0.1% or less, 32 Ohm load)
Other inputs and outputs
MIDI input (MIDI IN) DIN 5 pin
Format Standard MIDI format
MIDI output (MIDI OUT) DIN 5 pin
Format Standard MIDI format
USB connector USB 4-pin mini-B type
Format Mass Storage Class USB 2.0 High Speed
REMOTE connector 2.5-mm TRS jack
Audio performance
Frequency response 20 Hz to 20 kHz, +1/–1 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
Distortion ≤0.01 % (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
S/N ratio ≥90 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
Audio performance
Frequency response 20 Hz to 20 kHz, +1/–1 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
Distortion ≤0.01 % (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
S/N ratio ≥90 dB (MIC/LINE INPUT to STEREO OUT/EFFECT SENDS/MONITOR OUT)
Operating system requirements
Windows Pentium 300 MHz or faster
128 MB or more memory
Macintosh Power PC, iMac, G3, G4 266 MHz or faster
64 MB or more memory
Recommended USB port USB 2.0
Recommended USB host controller Intel chipset
Supported operating systems Windows XP, Windows Vista, Windows 7
Mac OS X 10.2 or later
Power requirements and other specifications
Power supply AC adaptor (TASCAM PS-1225L)
Power consumption 12 W (Phantom power on)
Dimensions (Width x Height x Depth, excluding projections) 514 mm x 104 mm x 340 mm
Weight 6.2 kg
Operating temperature 5–35 °C
Design and specifications subject to change without notice. |
RS-422 PROTOCOL CONVERTER
| 6-track Portable Multi-track Recorder
CD-Quality Recording (44.1kHz/16-bit)
Easy, Intuitive User interface
Built-in High-quality Stereo Condenser Microphone
Two Mic/Line inputs
Compact size and ultra light weight (360g/0.79lb without batteries)
Dedicated Level and Pan/Balance controls per track
Recording media: SD/SDHC card up to 32GB (2GB SD card included)
Recording: 2 tracks simultaneous
Playback: 6 tracks simultaneously
Power: Four AA batteries or optional AC adapter (PS-P520), optional external battery pack(BP-6AA)
Graphic LCD (128 x 64 dots)
Chromatic Tuner/Metronome
USB 2.0 Connection for Wav File import/export (Stereo and Mono)
Undo/Redo (includes Undo history)
Tripod socket hole
Auto punch in/out
Footswitch input
Dedicated stereo mix-down track
|
Designed for Windows based Pro Tools systems, the affordable Digidesign Pro Tools Custom Keyboard WIN let users work faster in their Pro Tools environment by providing direct access to primary transport and editing functions.
The Digidesign Pro Tools Custom Keyboard use the same symbols and color coding system built into the keyboards on the ICON D-Control worksurface and the other Digidesign control surfaces while retaining all the conventional alphanumeric labels that appear on standard computer keyboards. The Digidesign Pro Tools Custom Keyboard provides plug-and-play USB connectivity and offers a fresh new look at a lower price than ever before. The keyboard also supports a PS-2 connection for maximum compatibility.
Digidesign Pro Tools Custom Keyboard WIN Features
- Text and icons for main Pro Tools custom key commands, in addition to standard keyboard alphanumeric lettering
- Windows - PS-2 connection cord and USB adapter for easy connection with either method
|
Apogee makes the direct connection to Pro Tools | HD systems a reality. The Apogee X-HD option card allows for direct connectivity between Pro Tools HD™ systems and Apogee's X-Series or Rosetta 200 converters. The result is an incredibly powerful combination of Digidesign's™Ê¼ Pro Tools software and Apogee's superior conversion and clocking hardware. Features: - Primary HD port for connecting directly to HD Core or Accel cards.
- Expansion port for daisy-chaining multiple Apogee devices (AD-16X, DA-16X, Rosetta 800 & Rosetta 200)
- Compatible with the latest versions of ProTools
- May be used along side similar interfaces (such as Digidesign 96 I/O, 192 I/O, Prism Dream ADA-8)
- Please note: Not compatible with Pro Tools|HD Native
|
Reviews
There are no reviews yet.