| Content | Specifications:
- Recording media: SD card(64MB to 2GB), SDHC card(4GB to 32GB), SDXC card(48GB to 128GB)
- Recording format
• WAV: 44.1k / 48k / 96k Hz, 16bit / 24bit
• BWF: 44.1k / 48k / 96k Hz, 16bit / 24bit
- Number of channels: 4-channel (stereo × 2, mono × 4)
- Analog audio input
• Connector: XLR-3-31 (1:GND, 2:HOT, 3:COLD) / 6.3mm(1/4“)TRS standard jack
Set to "MIC / MIC+PHANTOM“
• Input impedance: 2k ohms
• Phantom power: 48V +/-4V(10mA/CH), 24V +/-4V(10mA/CH)
• Maximum input level: 0dBu
• Minimum input level: -72dBu
• MIC input gain: TRIM MAX
• LOW: +11dB
• HIGH: +51dB
• HI + PLUS: +63dB
• Input impedance: 10k ohms or more
• Standard input level: +4dBu
• Maximum input level: +20dBu
• Connector: 3.5mm(1/8“)stereo mini jack (this connector can be supplied plug-in power)
• Input impedance: 10k ohms
• Maximum input level: +10dBV
• Minimum input level: -50dBV
• MIC input gain: TRIM MAX
• LOW: +3dB
• HIGH: +26dB
• HI + PLUS: +38dB
• Connector: 3.5mm(1/8“)stereo mini jack
• Input impedance: 10k ohms
• Standard input level: -10dBV
• Maximum input level: +6dBV
Analog audio output
• Connector: 3.5mm(1/8“)stereo mini jack
• Output impedance: 200 ohms
• Standard output level: -10dBV
• Maximum output level: +6dBV
• Connector: 3.5mm(1/8“)stereo mini jack
• Output impedance: 200 ohms
• Standard output level: -40dBV
• Maximum output level: -24dBV
• Connector: 3.5mm(1/8“)stereo mini jack
• Maximum output level: 20mW + 20mW
USB
• Connector: Micro-B type
• Format: USB2.0 HIGH SPEED mass storage class
- REMOTE Connector: 2.5mm TRS jack
- Power: 4 AA batteries(Alkaline or NI-MH), USB bus power, Dedicated AC adapter(TASCAM PS-P515U, sold separately), Dedicated external battery pack(TASCAM BP-6AA, sold separately)
- Power consumption: 5.0W
- Continuous operation time: 2ch WAV, 44.1kHz, 16bit rec, Phantom power not used
- Dimensions: 169(W)×55.2(H)×106.5(D)mm (with the top adapter attached)
- Weight: 625g ( including batteries) / 530g (without batteries )
|
The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder.
The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness red and green indicators located around the RECORD button, which show STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE. The two button control allows the recorder to be placed into record mode, create a new record mark and stop the recording process.
The DNRP-WRC is primarily for the simple control of audio recording in areas where conversations, discussions or conferences are taking place. The unit allows the DNF450R/F650R recorder to be placed out of sight to prevent media tampering or access to all the recorder controls.
- Simple unobtrusive controller for the recording of audio in board/meeting rooms
- Easy connection to Denon DN-F450R/F650R recorder serial (RS232) port
- Provides bright visual indication of STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE
- RECORD and STOP buttons allow simple control without the need to access the recorder
- Ergonomic visually pleasing design with internal weight to prevent table slip
- Ultra low power consumption, no need for additional power adaptor
- Fully sealed label provides protection against drink spills
|
RS-422 PROTOCOL CONVERTER
|
The HD-R1 Solid State Recorder is a two-channel, single rack-mount recording and playback device created with the sound contractor in mind.
Utilizing the highly reliable Compact Flash Card the HD-R1 records 44.1 to 96kHz, 16/24 bit PCM or MP3 files. The ability to control the HD-R1 remotely is provided via RS-232, Parallel, and RJ45 100Mbit Ethernet. File transfer can be accomplished via Ethernet and/or USB (type "A" connector).
To further enhance the HD-R1's feature set, Mic preamps (w/20dB pad) and Phantom Power (rear-panel selectable) have been included. The HD-R1 offers a variety of contractor-friendly I/O options; such as, Unbalanced (RCA), Balanced (XLR and Euroblock), and S/PDIF Digital (Coaxial and Optical).
And of course... the traditional source device features are Power-on-Play, Front Panel Rotary Input Level Controls, Headphone Jack with level control, and a variety of Playback Modes.
* 1U Rack-mount Solid-State Recorder
* Compact Flash Card
* USB host interface for USB Flash Cards
* Audio data formats: PCM (16/24 bit), MP3
* Sampling rates supported: 44.1, 48, 88.2, 96kHz
* Mic/Line XLR (with 20dB pad) balanced I/O
* Phantom Power (rear panel switch and front LED indicator)
* Euroblock terminal (Input and Output)
* Unbalanced RCA (Input and Output)
* Front panel rotary input level controls
* RS-232 interface for control
* RJ45 100Mbit/s Ethernet interface for file transfer and control
* 25-pin parallel remote control interface
* 16 Direct Play via D=SUb25 pin parallel interface
* Power on play (front panel selectable)
* S/PDIF Digital In/Out (Coaxial and Optical)
* Headphone Jack w/level control
* Input through and Auto Fade function
* Input monitoring / mixing of live stereo input along with playback
* Program Play, Folder Play, Shuffle Play, Interval Play modes, etc...
|
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
* 0 dB = 0.775 V | Power Source | 220 - 240 V AC | | Power Consumption | 18 W | | Volume Adjustment | 100 mm motorized fader x 12
Rotary encoder x 8 | | Line Input | 1 channel (stereo) | | Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) | | Monitor Bus | 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) | | LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) | | Control | RS-232C: D-sub connector (9 pins) for maintenance use | | Finish | Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate | | Dimensions | 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43) | | Weight | 6.6 kg (14.55 lb) | | Accessory | Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3 | | Option | Console case: D-2012AS |
|
Apogee makes the direct connection to Pro Tools | HD systems a reality. The Apogee X-HD option card allows for direct connectivity between Pro Tools HD™ systems and Apogee's X-Series or Rosetta 200 converters. The result is an incredibly powerful combination of Digidesign's™Ê¼ Pro Tools software and Apogee's superior conversion and clocking hardware. Features: - Primary HD port for connecting directly to HD Core or Accel cards.
- Expansion port for daisy-chaining multiple Apogee devices (AD-16X, DA-16X, Rosetta 800 & Rosetta 200)
- Compatible with the latest versions of ProTools
- May be used along side similar interfaces (such as Digidesign 96 I/O, 192 I/O, Prism Dream ADA-8)
- Please note: Not compatible with Pro Tools|HD Native
|
Reviews
There are no reviews yet.