| Content | TASCAMʼs TM-80 is a condenser microphone designed and priced for home recording. The condenser mic features an 18mm aluminum diaphragm with a cardioid pickup pattern that sounds great on anything from vocals to acoustic instruments. Internal circuitry is optimized to reduce noise and distortion while retaining rich, full sound quality.
Included with the TM-80 are a tabletop stand, six-foot XLR cable, and a elastic shockmount to reduce rumble and noise during recording. Priced less than many dynamic microphones, the TM-80 is a must-have for any size studio. |
Transformerless Power/Output Module ? The SE 300 B is used with all AKG Blue Line capsules and operates from 9 ? 52 V phantom power. The 3-position switch allows selection of linear response, -10 dB preattenuation and 12-dB-per-octave 75 Hz low-cut filter. A stand adapter is included.
Specifications
Polar pattern: hypercardioid/directional
Frequency range: 20?20,000 Hz
Sensitivity: 25 mV/Pa (-32 dBV)
Max. SPL for 1 % THD: 124/134 dB
Equivalent noise level: 17 dB-A
Signal/noise ratio (A weighted): 77 dB
Preattenuation pad: -10 dB, switchable Bass cut filter: 12 dB/octave at 75 Hz
Electrical impedance: 200 Ohms
Recommended load impedance: >1,000 Ohms
Power requirement: 9 to 52 V phantom power to DIN 45 596
Current consumption: |
Technical specifications | Polar pattern | | hypercardioid | | Frequency range | | 50 to 20,000 Hz | | Sensitivity | | 20 mV/Pa (?34 dBV) | | Max. SPL | | 125 dB (k=1 %) | | Equivalent noise level | | 21 dB-A | | Signal/noise ratio (A-weighted) | | 73 dB | | Impedance | | 600 ohms | | Recommended load impedance | | >2000 ohms | | Supply voltage | | 9 to 52 V phantom power, requires DPA adapter (supplied with most Installation Modules) | | Current consumption | | | | Connector | | Discreet Acoustics Modular standard | | Finish | | matte dark gray | | Dimensions | | 13.5 x 20 mm dia. (0.5 dia. x 0.8 in.) | | Net weight | | 5 g (0.17 oz.) | | Shipping weight | | 88 g (3.1 oz.) | | Accessories (included) | | W 30 |
|
8 Wide frequency response range
High sensitivity, Low distortion
High input withstand S.P.L.
Rugged brass case, Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
PREMLIMINARY INFORMATION.
The MC10ST is a stereo microphone set including a pair of cardioid electret condenser microphones,
shock mount adapters, stereo mounting bracket and wind screens. The MC10ST can be used in a
wide range of applications, from studio and home recording to field or location sound aquisition.
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
Dedicated carry case as standard
SPECIFICATIONS:
Type: Back Electret Condenser Microphone
Polar Pattern: Cardioid
Frequency Response: 40Hz to 20kHz +/-10dB
Sensitivity: -40dBV/pa (10mv/pa)
Rated Impedance: 200ohm
Equivalent Noise Level: 22dB (A weighted IEC/DIN 651)
Maximum SPL: 134dB (THD |
C 568 B
Compact, short shotgun microphone
Integrated, switchable bass cut filter minimizes mechanical noise
Operates on phantom power
High directivity and wide frequency response in a relatively short shotgun make this
microphone a perfect tool for theater, sound reinforcement, and film/TV applications.
Due to its compact and lightweight design, the C 568 B is ideal for camera mount
applications. Below 500 Hz it functions as a hypercardioid microphone; above 500 Hz
the acoustic interference tube introduces increasing directivity. A switchable 12 dB/
octave 120 Hz bass cut filter effectively suppresses rumble and wind noise. The rugged,
all-metal body contains the built-in preamp. Phantom powering (9?52 V) required; foam
windscreen and stand adapter included.
SPECIFICATIONS:
Polar pattern hypercardioid/directional
Frequency range 20 to 20,000 Hz
Sensitivity 11 mV/Pa (-39 dBV)
Max. SPL 128 dB
Equivalent noise level (CCIR 468-3) 29 dB
Equivalent noise level 18 dB-A
Signal/noise ratio 76 dB
Bass filter 12 dB/octave at 120 Hz
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
The ME 62 is an omni-directional microphone head suitable for K6 and K6P
powering modules. It can be used for reporting, discussions and interviews.
The ME 62 is particularly suitable for good reproduction of 'room' ambience
and 'spaced omni' stereo recording. Matt black, anodised, scratch-resistant finish.
Features
Omni-directional pick-up pattern
Minimal inherent self-noise
Excellent rejection of rumble, wind and handling noise
Wide frequency response
High maximum sound pressure level
Integral pop filter
Delivery Includes
1 ME 62
Technical Data
Pick-up pattern omni
Sensitivity in free field, no load (1kHz) 31 mV/Pa +- 2,5 dB
Nominal impedance 200 Ohm (K6)
Min. terminating impedance 1000 Ohm (K6)
Equivalent noise level 15 dB
Equivalent noise level weighted as per CCIR 468-3 27 dB
Dimensions d 22,5 x 94 mm
Weight 30 g
|
Reviews
There are no reviews yet.