Content |
Telco module (with internal hybrid) for the D&R Airlab mixing console
The AIRLAB has the possibility to be loaded with up to 16 Telco modules.
Due to an ingenious Mix-Minus system alignment is only necessary during installation.
The AIRLAB Telco module is a straight forward design making communication very easy.
The first control is the front panel accessible, trimmer for side tone adjustment, only necessary during installation.
The Telco Send knob controls the outgoing signal to the caller. This signal is derived from the PROGRAM or SUB bus.
The line input can be switched to a balanced XLR input connector to accept an external (digital) hybrid instead of its own internal hybrid.
A separate input gain control with HP and LP filters be used to enhance intelligibility.
The SUB and PROGRAM assign switch routes the signal to both outputs if needed.
The stereo Aux. control has jumpers that select its source to be pre or post VCA/MUTE.
A Pan-pot and CUE/Select switch plus the ON switch completes the Telco module.
A 100mm linear fader controls a high quality THAT VCA, eliminating any fader wear out in the future.
Connecting a Caller can be accomplished with the ON switch when the fader is up or with the CUE/SELECT/RING switch when the fader is down.
When CUE is active in the TELCO module, the caller is connected to the CUE bus and also the engineers talk-back, but does not go ON-AIR yet as the fader is down.
It is possible to connect both the Cue and On switch to a remote unit, allowing a director to control the broadcast.
A "Connect" LED positioned below the High Cut switch indicates that the internal Hybrid is active.
| 4-Channel Analog Output Card
Mini-YGDAI cards make it easy to add I/O in a wide variety of audio and network formats to Yamaha digital mixing consoles, processors, and power amps that are equipped with compatible card slots. Mini-YGDAI cards can give your system the most up-to-date capabilities for any application.
Features
- 20bit resolution, 4-out analog audio interface
- 4x XLR3-32 connectors (balanced)
- Max onput level before clip: +18dBu (default) / +4dBV
- Cannot be used at 96kHz
Specifications
General Specifications |
Channel Count |
4OUT |
Format |
Analog |
Max output level |
+18dBu(default) / +4dBV
*GAIN switches at each output port |
Sampling frequency |
44.1/48 kHz |
Resolution |
20 bit |
Connector |
4x XLR-3-32 type connectors (balanced) |
| Suitable for use with many Soundcraft mixing consoles including:
200SR (24ch), 200B (24ch), 200BVE (8ch), 200 Delta (24ch), Delta AVE (8ch)
DC power connector: 5 pin screw-lock
3 Output rails: +17V, -17V, +48V
Power requirements: 110/120/220/240VAC ±10% 50/60Hz
Input power: 100VA
Dimensions: 483(w) x 195(d) x 89(h)mm
Physical: standard 19" (2u) rack mount kit included
Weight: 5kg | 8-Channel AES/EBU I/O Card with REF Video Input
The MY8-AEB is an eight-channel digital input/output card that complies with the AES 3id-1995 standard. It provides video input jacks that allow the host device in which the MY8-AEB is installed to be synchronized to a video signal.
In addition to 8 BNC connectors (4 stereo inputs and 4 stereo outputs) the MY8-AEB has a REF Video input that can be used to receive a PAL or NTSC format Reference video (Black Burst) signal that will provide the synchronization word clock for the device into which the card is installed.
Features
- 24bit resolution, 8-in/8-out AES/EBU interface
- 9x BNC connetors: 4x IN, 4x OUT, 1x Reference video input
- “eXi-Clock" synchronization maintenance function
Specifications
General Specifications |
Channel Count |
8IN / 8OUT / 1REF Video IN |
Format |
AES/EBU (AES-3id) |
Resolution |
24 bit |
Connector |
8 x BNC(4 x AES In, 4 x AES Out)
1 x BNC (Reference Video In with "eXi-Clock" sync capability) |
*“eXi-Clock" is a function that is capable of seamlessly continuing word clock generation even if the Reference video signal is interrupted. |
Yamaha PSL120 Cable for connecting 2 x PW800W
The Yamaha PSL120 will provide you with a fail-safe solution to connecting your PW800W power supplies. Once your power supplies are connected you can access multiple PM5D/PM5D-RH consoles.
|
Yamaha MBCL Meterbridge - for the CL1 and CL 3, Includes fitting kit |
Reviews
There are no reviews yet.