Content |
Thorens TD 202 Turnable
Compared with its "smaller” brother TD 201 it comes with a more massive plinth and a AT 95E cartridge.
New TD 202 completes the new series of manual plug and play turntables. Compared with its "smaller” brother TD 201 it comes with a more massive plinth and a AT 95E cartridge.
SPECIAL FEATURES
The integrated phono stage includes an additional analogue/digital converter with USB out. So the record played will be automatically digitized and can easily be recorded on a computer using several kinds of recording software that can be downloaded from the web.
TD 202 Specification
Turntable section
Drive System Belt Drive
Motor DC
Motor Speed 33 1/3 RPM, 45 RPM
Rotation Speed Variation +/–2%
Wow and Flutter 0.2%
Signal-to-Noise Ratio 67dB or higher (A-weighted, 20kHz LPF) 60dB or higher (unweighted, 20kHz LPF)
Platter Aluminum Die-cast Diameter of Platter 12“, 300mm
Tonearm section
Alumi tube
Type Static Balance, Straight
Effective Arm Length 8.8“, 223.6mm
Stylus Pressure Range 0 to 4g
Supported Cartridge Weight 3.5 to 6.0g
Overhang 18.6mm
Anti-skating Adjustment Supported
Cartridge section
Type MM type (Audio-Technica AT-95E)
Stylus Construction Bonded Diamond
Frequency Response 20Hz to 20kHz
Channel Separation >18dB
Channel Balance 2.5dB
Vertical Tracking Angle 20 degrees
Supported Load Impedance 47k ohms
Output Voltage 2.5mV (1kHz, 3.54cm/sec.)
Stylus Pressure 2.0g +/–0.5g
Cartridge Weight 5.7g +/–0.5g Head-shell
Weight 11g (including Screws, Nuts and Wires)
Analog Output
Connector RCA Pin jack (Gold-plated) Power AC 100 to 240V, 50/60Hz Power Consumption 1.5W (less than 0.5W at Standby)
Overall Dimensions (W x H x D) 420 x 355x 121mm
Weight Approx. 3.9 kg
|
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
-
Belt drive system with low vibration DC motor
-
Central gravity mass point made from artificial stone
-
Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
-
Low resonance MDF platter with felt mat
-
8,6” ultra low mass tonearm with straight arm tube
-
Pre-adjusted tracking force & antiskating
-
Gold-plated RCA contacts & cartridge pins
-
Colour options: red-black, white-black, silver-black
Specifications:
-
speed : 33, 45 (manual speed change)
-
Speed variance: 33: 0,2% 45: 0,18%
-
Wow & flutter: 33: 0,14% 45: 0,13%
-
platter: 300mm MDF
-
tonearm: 8,6” metal tube
-
effective arm length: 218,5 mm
-
overhang: 22,0 mm
-
effective tonearmmass: 8,0gr
-
counterweight for cartridge mass: 3 - 5,5g (included)
-
tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
-
output: RCA to phono input
-
included accessory: RCA cable, 15V DC power supply
-
power consumption: 4,0 watts
-
dimensions: 430 x 90 x 300mm (WxHxD)
-
weight: 2,7 kg net
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
| DENON DP-300F Belt-driven automatic turntable with cartridge
Fully automatic operation makes the DP-300F easy to use.
With the touch of a button, the tonearm swings over
and begins playing your record, returning to its original position when finished.
Details:
aluminum platter
built-in phono preamp
belt-drive system with DC servo motor
dynamic balance tonearm with universal mount
fully automatic operation
manual lifter mechanism
replaceable moving magnet cartridge included
removable dust cover
heavy base construction
minor assembly required
two speeds: 33-1/3 rpm & 45 rpm
wow & flutter 0.10%
weight: 6 kgs
dimensions:17-1/16“W x 4-13/16“H x 15“D | Cardan bearing with zero-mass tracking force setting by a
high-precision torsion spring.
Removable headshell with 1/2 inch fixing holes. Adjustable
tracking force and anti-skating.
Headshell made of carbon fiber for special rigid torsion.
Chassis technology
Solid wooden console. Floating sub-chassis.Vibration
-damped aluminum turntables with anti-static felt mat.
Drive technology
Belt drive with smooth flat belt. DC motor with electronic rotary speed control. Viscosity-damped tone
arm lift. Automatic tone-arm cueing mechanism. Auto stop with ton arm return. Possibilities to play-back
archived discs with a rotational speed of 78 Upm.
Delivered with magnetic pick-up OMB 10.
High quality, fully automatic turntable with three speeds (33, 45, 78 rpm). This turntable meets all the criteria. Sophisticated technology, greatest convenience combined with great sound leaves the listener with no unfulfilled wishes.
Tone arm technology:
Cardan bearing with zero-mass tracking force setting, thanks to precision torsion spring. Detachable headshell with 13mm (1/2-inch) fixing-holes. Adjustable tracking force and anti-skating. Extremely rigid headshell made of carbon fiber.
Chassis technology:
Solid wooden chassis. Floating sub chassis. Vibration damping aluminium platter with antistatic felt mat.
Drive technology:
Belt drive with polished flat belt. DC motor with electronic speed control. Viscosity-damped arm lift. Automatic tone arm cue. Auto Stop with tone arm return. Playback option for archive disks with 78 rpm speed. Delivered with OMB 10 cartridge.
Specifications:
- Speed r/min.: 33/45/78
- Speed a ccuracy in% DIN / WRMS: < -/+ 0,07 / 0,04 % DIN
- Rumble-to-noise ratio: 48 dB
- Rumble-noise ratio: 72 dB
- Cartridge system: OMB 10
- Frequency Response: 20 Hz - 22 kHz
- Depth sensing capability (300 Hz): 70 µm at 315 Hz
- Dimensions (WxHxD): 440 x 119 x 360 mm
- Weight: 5,43 kg
- Colour: black / silver
- Power supply: 12V DC, 150 mA
|
Reviews
There are no reviews yet.