Content | The new Thorens TD 201 is the right choice for anyone looking for a robust, easy to use plug and play turntable. It comes with a smooth running belt drive and a aluminium platter with rubber mat. The new Thorens TP 71 tonearm uses a detachable headshell with preconfigured AT 3600 cartridge.
SPECIAL FEATURES
Using the switchable integrated phono stage the TD 201 can be connected to any amplifier or receiver even if it does not have a specific input for phono devices.
TD 201 Specification
Turntable section
Drive System Belt Drive
Motor DC Motor
Speed 33 1/3 RPM, 45 RPM
Rotation Speed Variation +/–2%
Wow and Flutter 0.2%
Signal-to-Noise Ratio 67dB or higher (A-weighted, 20kHz LPF) 60dB or higher (unweighted, 20kHz LPF)
Platter Aluminum Die-cast Diameter of Platter 12“, 300mm
Tonearm section Alumi tube
Type Static Balance, Straight
Effective Arm Length 8.8“, 223.6mm
Stylus Pressure Range 0 to 4g
Supported Cartridge Weight 3.5 to 6.0g
Overhang 18.6mm
Anti-skating Adjustment Supported
Cartridge section
Type MM type (Audio-Technica AT3600)
Stylus Construction Bonded Diamond
Frequency Response 20Hz to 20kHz
Channel Separation >18dB Channel Balance 2.5dB
Vertical Tracking Angle 20 degrees
Supported Load Impedance 47k ohms
Output Voltage 2.5mV (1kHz, 3.54cm/sec.)
Stylus Pressure 3.5g +/–0.5g
Cartridge Weight 5g +/–0.5g
Head-shell Weight 10g (including Screws, Nuts and Wires)
Analog Output
Connector RCA Pin jack (Gold-plated)
Power AC 100 to 240V, 50/60Hz Power Consumption 1.5W (less than 0.5W at Standby)
Overall Dimensions (W x H x D) 420 x 355x 121mm
Weight Approx. 3.9 kg |
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
-
Belt drive system with low vibration DC motor
-
Central gravity mass point made from artificial stone
-
Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
-
Low resonance MDF platter with felt mat
-
8,6” ultra low mass tonearm with straight arm tube
-
Pre-adjusted tracking force & antiskating
-
Gold-plated RCA contacts & cartridge pins
-
Colour options: red-black, white-black, silver-black
Specifications:
-
speed : 33, 45 (manual speed change)
-
Speed variance: 33: 0,2% 45: 0,18%
-
Wow & flutter: 33: 0,14% 45: 0,13%
-
platter: 300mm MDF
-
tonearm: 8,6” metal tube
-
effective arm length: 218,5 mm
-
overhang: 22,0 mm
-
effective tonearmmass: 8,0gr
-
counterweight for cartridge mass: 3 - 5,5g (included)
-
tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
-
output: RCA to phono input
-
included accessory: RCA cable, 15V DC power supply
-
power consumption: 4,0 watts
-
dimensions: 430 x 90 x 300mm (WxHxD)
-
weight: 2,7 kg net
|
JB Systems Q3-USB features: - high torque direct drive motor
- fast start / stop
- 3 speeds: 33, 45, 78 rpm with quartz lock
- 2 pitch adjustment ranges: +/-10% ; +/-20%
- forward / reverse play
- starting torque: More than 1.6kgf / cm
- starting time: less than 1 second
- braking time: less than 1 second
- tracking error angle: less than 3°
- USB-output for direct recording to any PC
- free, multilingual Audacity software available via download:
- endless possibilities with free downloadable effect plug-ins
- import, export and edit Ogg Vorbis, MP3, AIFF and WAV sound files.
- cut, copy, splice, and mix sounds together.
- change the speed or pitch of a recording.
- remove static, hiss, hum, or other constant background noises.
- alter frequencies with Equalization, FFT Filter, and Bass Boost effects.
- adjust volumes with Compressor, Amplify, and Normalize effects.
- selectable phono/line output
- all functions are equipped with stylish, blue LED lights
- plastic dust cover
- retractable target light
- Audio Technica cartridge included
- all metal S-shaped tone arm assembly with: counterweight, anti-skating adjustment, lever lift with
- height adjustment
- adjustable large feet for perfect leveling
- phono output: 1,5~3,6mV
- line-output: 90~216mV
- PC interface: USB 1.1 compatible (Win XP/Vista/Win7 or Mac OS X)
- power supply: 230V
- power consumption: 11 watt
- dimensions: 450 x 352 x 157 mm
- weight: 10,5 kg
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
|
• High precision turntable with cast aluminum plate • Fully automatic system for easy operation • Built-in equalizer for connection to PHONO input • Transfer music from analog LP to USB memory (without PC) • Includes PC software for assembling tracks
The DP-200USB is a fully automatic record player that easily converts your analogue records into digital files and stores them onto a USB memory stick. Using USB memory makes it easy to carry your digital files when you donʼt have a PC near your record player. Easily store your record library onto USB memory: Simply insert your USB memory stick into the USB port on the front, press the Start and Record buttons, and the DP-200USB converts your record into digital files. You don\'t need to have a PC nearby. When you insert the USB memory stick into a DENON S-52DAB or RCD-M37DAB, you can enjoy the music files in the high-quality sound that Denon audio products are renowned for. You can also record the music to a USB player that supports MP3 files and enjoy listening to the music directly from the player. Includes Trans Music Manager, to obtain track numbers and information: The DP-200USB comes with Trans Music Manager (on CD-ROM) that detects the silent spaces between tracks to automatically split track numbers. You can also use a PC to access the Gracenote® music ID server and obtain track information. Built-in Phono Equalizer: The DP-200USBʼs built-in Phono Equalizer lets you enjoy the music on a mini audio system or radio cassette player that does not have a PHONO jack. (The Phono Equalizer can be switched on or off.) Fully automatic player: When you select the 30cm (12“) or 17cm (7“) record size, the arm automatically moves to the correct position for playing the record, and after itʼs finished, the arm automatically returns to its original position. This automatic system makes it easy to play records on the DP-200USB. Aluminium diecast turntable: The DP-200USB has an aluminium diecast turntable for high inertial mass and stable rotation. Includes MM cartridge Trans Music Manager functions: Auto MP3 Splitter: Detects silent part between tracks and automatically tags tracks / Manual MP3 Splitter: Manually tags tracks as you wish / Auto Music ID Record: automatically enables to record music information including titles / Manual MusicID Record: manually enables to record music information including titles / Required System OS; Microsoft® Windows® Vista/XP/2000 / Language: ENGLISH, GERMAN, FRENCH Color variations: Silver and Black Drive system: Belt Drive Motor Motor: DC Servo Motor Speed: 33-1/3, 45 rpm Wow & flutter: 0.15 % (WRMS) Tonearm: Type Dynamically Balance type, Straight Tonearm Cartridge: Type MM / Replaceable stylus number DSN-84 / Output Voltage with equalizer OFF 2.5 mV, with equalizer ON 150 mV Digital recording media: USB memory (Mass Storage Class) Digital recording file type: MP3, 192 kbps Power supply: AC 230 V, 50 Hz Power consumption: 12 W Dimensions (WxHxD): Dust cover closed 360 x 98 x 358 mm / Max., Dust cover opened 360 x 415 x 363 mm Weight: 3.2 kg |
Reviews
There are no reviews yet.