| Content | The new Thorens TD 201 is the right choice for anyone looking for a robust, easy to use plug and play turntable. It comes with a smooth running belt drive and a aluminium platter with rubber mat. The new Thorens TP 71 tonearm uses a detachable headshell with preconfigured AT 3600 cartridge.
SPECIAL FEATURES
Using the switchable integrated phono stage the TD 201 can be connected to any amplifier or receiver even if it does not have a specific input for phono devices.
TD 201 Specification
Turntable section
Drive System Belt Drive
Motor DC Motor
Speed 33 1/3 RPM, 45 RPM
Rotation Speed Variation +/–2%
Wow and Flutter 0.2%
Signal-to-Noise Ratio 67dB or higher (A-weighted, 20kHz LPF) 60dB or higher (unweighted, 20kHz LPF)
Platter Aluminum Die-cast Diameter of Platter 12“, 300mm
Tonearm section Alumi tube
Type Static Balance, Straight
Effective Arm Length 8.8“, 223.6mm
Stylus Pressure Range 0 to 4g
Supported Cartridge Weight 3.5 to 6.0g
Overhang 18.6mm
Anti-skating Adjustment Supported
Cartridge section
Type MM type (Audio-Technica AT3600)
Stylus Construction Bonded Diamond
Frequency Response 20Hz to 20kHz
Channel Separation >18dB Channel Balance 2.5dB
Vertical Tracking Angle 20 degrees
Supported Load Impedance 47k ohms
Output Voltage 2.5mV (1kHz, 3.54cm/sec.)
Stylus Pressure 3.5g +/–0.5g
Cartridge Weight 5g +/–0.5g
Head-shell Weight 10g (including Screws, Nuts and Wires)
Analog Output
Connector RCA Pin jack (Gold-plated)
Power AC 100 to 240V, 50/60Hz Power Consumption 1.5W (less than 0.5W at Standby)
Overall Dimensions (W x H x D) 420 x 355x 121mm
Weight Approx. 3.9 kg |
A MUSICAL FAMILY
The TD 206 and TD 209 turntables are the younger siblings of the revolutionary, multiple-award-winning TD 309. However, they don’t have to live in the shadow of their older brother. Both models are built using only high-quality materials and parts. And both share a number of technical features with the TD 309, ensuring that their replay quality is up there with the best.
The new TP 90 tonearm is based on the tried-and-tested TP 92 and uses the same ultra-low-friction, high-performance bearing and the innovative zero-stiction anti-bias system. The arm tube is made from rolled aluminium that is damped using RMR technology (reduced-modal-resonance), and the stainless-steel counterweight at the end of the arm tube is double-decoupled. Tonearm height, azimuth and overhang are useradjustable.
SPECIAL FEATURES
- Low Noise, Low Voltage electronically speed controlled DC Motor
- Adjustable belt tension for best performance
- Two-part aluminium/acrylic platter
- New TP 90 tonearm with precision Japanese bearings
- Tonearm adjustable for VTA, azimuth and overhang
- Made in Germany
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
|
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
-
Belt drive system with low vibration DC motor
-
Central gravity mass point made from artificial stone
-
Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
-
Low resonance MDF platter with felt mat
-
8,6” ultra low mass tonearm with straight arm tube
-
Pre-adjusted tracking force & antiskating
-
Gold-plated RCA contacts & cartridge pins
-
Colour options: red-black, white-black, silver-black
Specifications:
-
speed : 33, 45 (manual speed change)
-
Speed variance: 33: 0,2% 45: 0,18%
-
Wow & flutter: 33: 0,14% 45: 0,13%
-
platter: 300mm MDF
-
tonearm: 8,6” metal tube
-
effective arm length: 218,5 mm
-
overhang: 22,0 mm
-
effective tonearmmass: 8,0gr
-
counterweight for cartridge mass: 3 - 5,5g (included)
-
tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
-
output: RCA to phono input
-
included accessory: RCA cable, 15V DC power supply
-
power consumption: 4,0 watts
-
dimensions: 430 x 90 x 300mm (WxHxD)
-
weight: 2,7 kg net
|
The TD 158 is a complete and comfortable record player. Plug-and-play, so to speak. It goes without saying that it features a fully automatic mode of operation, an electronic speed selector and last but not least, a high-quality acrylic cover to keep dust away.
Tonearm and cartridge have been pre-mounted and painstakingly adjusted in the factory. All necessary leads are supplied with the unit and the record player is ready to play with a flick of the wrist. The entry into the wonderful world of analog music is as simple as this!
Fully automatic, internal flat drive belt,
Speeds 33-1/3, 45 rpm, Tonearm THORENS TP 17, Pick-up Cartridge DN 251 S,
Dimensions 440 x 120 x 360 mm (W x H x D),
Finish black structured enamel ,mains adapter, dust cover (acrylic), RCA interconnects
| Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
- Belt drive system with low vibration DC motor
- Central gravity mass point made from artificial stone
- Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
- Low resonance MDF platter with felt mat
- 8,6” ultra low mass tonearm with straight arm tube
- Pre-adjusted tracking force & antiskating
- Gold-plated RCA contacts & cartridge pins
- Colour options: red-black, white-black, silver-black
Specifications:
- speed : 33, 45 (manual speed change)
- Speed variance: 33: 0,2% 45: 0,18%
- Wow & flutter: 33: 0,14% 45: 0,13%
- platter: 300mm MDF
- tonearm: 8,6” metal tube
- effective arm length: 218,5 mm
- overhang: 22,0 mm
- effective tonearmmass: 8,0gr
- counterweight for cartridge mass: 3 - 5,5g (included)
- tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
- output: RCA to phono input
- included accessory: RCA cable, 15V DC power supply
- power consumption: 4,0 watts
- dimensions: 430 x 90 x 300mm (WxHxD)
- weight: 2,7 kg net
|
Reviews
There are no reviews yet.