Velodyne DD-10 PLUS ACTIVE Subwoofer

Length    No
Accessories    Remote Control, Digital Drive Plus Accessory Kit, Video Cable
Amplifier    3000 watts Dynamic, 1250 watts RMS Power
Auto On/Off    Yes
Cabinet Design    Sealed servo enclosure
Dimensions: (H/W/D)    14.2" x 13" x 16.6“
HiPass Crossover    80 or 100 Hz at 6 dB/octave
LoPass Crossover    40 Hz to 199 Hz (variable in 1 Hz increments) selectable slope Default: 80 Hz @ 24 dB/Octave
Phase Control    0, 180 Degrees
Removable Grille    Yes
Shipping Weight    77 lbs. (35 kg)
Size    No
Voice Coil    Six-layer, 65mm
Warranty (N. Am.)    Two years (electronics & drivers - parts & labor)

System Format:    Sealed Cabinet. 25mm M.D.F construction with internal bracing. Sealed amplifier compartment
Low Frequency Limit:    18 Hz
Upper Frequency Limit:    40 - 120 Hz Variable
Low Pass Filter Alignment:    Active 4th order 24dB/octave (6/12/18/24 dB user adjustable)
Amplifier Power Output    650 watts Continuous. 1200 watts (peak)
Amplifier Classification    D2AudioTM* DSP controlled, Class-D amplifier system. High current switch mode power supply (smpsu)
Equalisation    4 Settings (Off/Music/Movie/Impact)
Phase Control    0-90-180-270 degrees
Auto Sensing Input Level Requirements    Line Level > 2mV. Standby after 10 minutes if no signal sensed
Digital Volume Level    -60 to +10dB in 1dB increments
Drive Unit Complement    1 x 15” C-CAM® sub-woofer driver featuring triple suspension
3” long throw voice coil
12V Trigger Input    3.5mm mono jack socket
Connections    Stereo RCA in/out
LFE in/out
12V Trigger in (3.5mm mono jack)
LEO* - 3.5mm Microphone input jack (microphone supplied)
Input Impedance    20 kohms
Dimensions (H x W x D)    430 x 400 x 400 mm (16 15/16 x 15 3/4 x 15 3/4 Inches)
Grille Depth    28 mm (1 1/8 Inches)
Weight (unpacked)    35.3 kg (77.6 lbs)
Mains Input Voltage    100 - 120 Vac / 220 - 240 Vac 50/60 Hz (Factory preset)
Electrical Certifications    CE/CB/ETL/Fcc/ErP (Energy saving compliant)
Power Consumption    Maximum 1000W. Standby Fuse Type    20mm UL/VDE (Value is region specific)
IR Remote Control Code    NEC SH6122

Dimensions | Metric :16-3/4” W x 16-3/4” D x 16-15/16” H | 42.5 x 42.5 x 43.0 cm
Driver Complement :One high-definition 14" long throw woofer, pressure coupled to two 14” low bass radiators
Frequency Response :11 Hz – 200 Hz
Internal Amplifier Power :1800 watts
Auto On / Off :Signal Sensing (US) | Signal Sensing and Switched (International)
Power Requirements :110 volts Alternating Current (US) | 220 volts Alternating Current (International)
High Level Inputs :Two pairs of 5 way binding posts
High Level Outputs :Two pairs of 5 way binding posts
Subwoofer Inputs :One LFE input (for SW preout only)
Low Level Inputs :Two low level inputs: left and right low level in
Low Level Outputs :Two low level outputs: left and right low level out
High Level High Pass Crossover :Non Variable 6 dB/octave @ 80 Hz: Available only with high level inputs and outputs only
Low Level High Pass Crossover :12 dB/octave continuously variable from 40 Hz to 150 Hz: Available only with low level inputs and outputs
Low Pass Crossover% :24 dB/octave continuously variable from 40 Hz – 150 Hz: Available only with high level inputs and outputs or low level inputs and outputs
Available Finishes :Piano-Gloss Black
Accessories :Rubber feet; Isolation spikes
Fuse :8 amp 250 volt Slo Blo (US) | 4 amp 250 volt Slo Blo (International)
Weight | Metric :97 lbs | 44.0 kg
Warranty :5 Years; 3 Years for Amplifiers

Dimensions | Metric :10-5/16” W x 15-3/4” D x 12-7/8” H | 26.2 x 40.0 x 32.7 cm
Driver Complement :One high-definition 8" woofer pressure coupled to one 8" low bass radiator.
Frequency Response :20 Hz – 150 Hz
Internal Amplifier Power :300 watts
Auto On / Off :Signal Sensing (US) | Signal Sensing and Switched (International)
Power Requirements :110 volts Alternating Current (US) | 220 volts Alternating Current (International)
High Level Inputs :Two pairs of 5 way binding posts
High Level Outputs :Two pairs of 5 way binding posts
Low Level Inputs :One LFE input (for SW preout only)
High Pass Crossover :Non Variable 6 dB/octave @ 80 Hz: Available only with high level inputs and outputs
Low Pass Crossover% :24 dB/octave, continuously variable from 40 Hz – 150 Hz: Available with high level inputs only
Available Finishes :Matte Black; Matte White
Fuse :3.2 amp 250 volt Slo Blo (US) | 2 amp 250 volt Slo Blo (International)
Packaging :Packaged individually or as part of ProCinema 800 system
Weight | Metric :26 lbs | 11.8 kg
Warranty :5 Years; 3 Years for Amplifiers

Amplifier Output: 1000 watts (RMS) 2000 watts (Peak)
Frequency Response: 16Hz to 40/160Hz variable
Crossover (Low Pass): 40Hz - 160Hz Variable slope characteristic from
12 - 36dB/Octave
Sub-Sonic Filter (High Pass): 16Hz - 31Hz
EQ: 4 x Presets 1 x User Setting
Equalisation: Graphic 9 band Equaliser ±6dB in 0.5dB steps
Volume Level: -80 - 0dB (1dB increments from 0 to -30dB & 2dB
increments from -31 to -80dB)
Auto Sensing Input Requirements: Line Level>5mV (RMS) Variable delay time
5, 10, 15, 20, 25 & 30 minutes
Variable Phase Control: 0. 45. 90, 135, 180, 225, 270 & 315º
Internal Memory: 3 Independent memory locations
Cabinet Specification:
Sealed Cabinet with 25mm thick M.D.F
construction with critical internal bracing
Amplifier Classification:
Class-D amplifier with DSP control
Driver Complement:
1 x 15" C-CAM long throw sub-woofer driver featuring triple suspension and a 4" long throw voice coil

External Dimensions -
Excluding Plinth: Width: 485mm (19 inches)
Height: 455mm (18 inches)
Depth: 475mm (18 3/4 inches)
Weight: 50 Kg (110lbs)
Mains input Voltage: 100 - 240 Vac 50/60Hz (Factory Set)
Trigger Input:
3.5mm Jack input, +12Vdc = On State

User's Manual

AVAILABLE IN THESE COLOR FINISHES