Content |
Signal distributor. 1 stereo input / 4 stereo outputs or 1 mono input / 8 mono outputs
This audio distributor is very useful to supply several audio devices with only one audio source. Its 2 operating modes allow to work with mono or stereo signals. Output level can be controlled independently.
WD 421 adapts itself to work with different impedances, ensuring that output signal level is at least equal to input signal level. It avoids any undesired attenuation and features a LED vumeter to visualize the input signal level.
Audio signal distributor with 2 inputs and 8 outputs. Two operating modes: 1 stereo input with 4 stereo outputs. 1 mono input with 8 mono outputs. Adjusting Output level. Balanced LINK output for interconnecting several units. Individual gain control of each channel
Inputs: 2 x XLR3 female balanced. Outputs: 8 x XLR3 male balanced. Input sensitivity: 0 dBu. Max. level input: 22 dBu. Input impedance: 10 kohm. Level range: ? to - 12dBu. Frequency response: 20 Hz to 22 kHz. Distortion: 110 dBu. Noise and hum: < - 80 dB @ 20 Hz - 22 kHz. Crosstalk: < - 80 dB @ 20 Hz - 22 kHz. Output impedance: 120ohm. Main supply: 110 - 120 V / 220 - 240 V 50/60 Hz. Power consumption: 20 W. Dimensions (WxHxD): 483 x 44 x 220 mm. Weight: 2.75 kg. |
A passive dual channel line splitter that is mainly used to feed the left and right master outputs of a mixer into several inputs such as power amplifiers, recording machines etc. A specially designed audio frequency transformer maintains signal integrity and prevents ground loop hum. This unit also converts unbalanced signals into balanced signals and vice versa. Rugged diecast aluminium box.
Technical specifications:
2 channel micro splitter "1 into 3“, each channel with:
- Input: female XLR type with parallel male XLR Type
- Output 2 transformer isolated male XLR type outputs
- Transformer ratio 1 : 1 Nominal level: 0 dB, max. level +20 dB
- Nominal impedance input and output: 600 ohms
- Ground lift switch
| 1231 Dual 31-Band Graphic Equalizer
The dbx? 12 Series were designed to meet the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls. The 1231 provides standard features like dual-channels, 31 1/3 octave bands, ISO frequency centers, +/- 12 dB input gain range, and switchable 40Hz/18 dB per octave low-cut filters, but also includes other insightful features. These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS connectors for installation ease; balanced inputs and outputs for quiet operation; and chassis/signal ground lift capabilities for quick hum isolation. The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years of maintenance-free operation in any application. The magnetically isolated transformer, electronically balanced/unbalanced inputs and servo balanced/unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire relay bypass with 2 second power up delay were steps our engineers took to ensure compatibility for all installations. Only the best components were utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR (ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail is contained in a 3U steel/aluminum chassis.
SPECIFICATIONS:
INPUT |
Connectors: |
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip |
Type: |
Electronically balanced/unbalanced, RF filtered |
Impedance: |
Balanced 40 kOhm, unbalanced 20 kOhm |
Max Input Level: |
>+21dBu balanced or unbalanced |
CMRR: |
>40dB, typically >55dB at 1kHz |
OUTPUTS |
Connectors: |
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
Type: |
Impedance-balanaced/unbalanced, RF filtered |
Impedance: |
Balanced 200 ohm, unbalanced 100 ohm |
Max Output Level: |
>+21dBu balanced/unbalanced into 2 kOhm or greater
>+18dBm balanced/unbalanced (into 600 ohm) |
SYSTEM PERFORMANCE |
Bandwidth: |
20Hz to 20kHz, +0.5/-1dB |
Frequency Response: |
50kHz, +0.5/-3dB |
|
+/-15dB range |
+/-6dB range |
Dynamic Range: |
109dB |
115dB |
Signal-to-Noise: |
90dB |
97dB |
THD + Noise: |
|
|
About the DI6s It's a fact of audio life that a lot of equipment that has to be connected to professional audio systems isn't impedance or level compatible. Interfaces Unlimited Tape/cassette/DVD/CD decks, audio for video, drum machines, synthesizers, bass guitars, computers; at some stage all these need linking up to Balanced inputs, whether the application is Live sound, Studio or Broadcast. To solve these problems, we've developed the DI-6s:
Six active D.I. (Direct Injection) boxes, plus a 6 into 1 Line Mixer, plus a 1 to 6 Splitter, All of this in a compact, all steel 1 RU package.
A Pro Audio Toolbox This unique and flexible audio toolbox allows Six independent unbalanced audio sources to easily and quietly interface with Balanced pro audio systems, either to individual channels or summed down to one Master output. But that's not all. By pressing a single switch on the rear panel the DI6s will change from being Direct Boxes and a Mixer to being a 6 way Splitter (line distribution amplifier). Now it will split an incoming signal to 6 individual outputs or zones. On the front panel, each channel has 2 IN/OUT jacks, a level control from infinity (off) through 0dB to +15dB gain, and a Clip indicator LED.The Master section has a Master volume control and status LEDs indicating whether the unit is in DI or Splitter mode. In addition, as on all ARX single rack unit equipment, each channel has a numbered marker panel ('scribble strip') you can write on for easy confirmation of channel assigns. Balanced Outputs On the rear, each channel has an XLR Balanced output, with associated Ground lift switch and status LED, to isolate the chassis and electronic grounds. The Master section has both Balanced XLR and Unbalanced Jack outputs. In addition there is a Balanced XLR input with a switch to put the unit in either DI or Splitter mode. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and voltage change switch. With so many handy functions, plus a true 'user friendly' layout, it's no wonder people call the DI-6s 'A total Audio Patching System in 1 RU!' You'll never compromise on Quality when you choose ARX
Features Unique Pro Audio problem solver Six Direct boxes, Splitter and Line Mixer in one unit Multi mode unit: Six in, Six out; Six in, One out; One in, Six out Individual Output Ground lift switches Up to +15dB Gain available per channel Balanced XLR Outputs; High Impedance Jack Ins and Outs Flawless performance in any audio environment
T E C H N I C A L S P E C I F I C A T I O N S
Channels 1 - 6 High Z Input Impedance 2.2 Meg Ohm Max Channel Gain 15dB Clip LED Illuminates 1dB prior to clip Direct Output Impedance 300 ohms Balanced Max Input Level +20dB Max Output Level +21dB Signal to Noise -96dB(unity gain) Frequency Response 20Hz to 20KHz, ±0.5dB Distortion < 0.004%, 1KHz, +4dB Output Connector 3 pin XLR Master Section Output Impedance 300 Ohms Balanced Max Output Level +21dB Signal to Noise -90dB (unity gain) Frequency Response 10Hz to 20KHz, ±0.5dB Distortion < 0.004%, 1KHz, +4dB Output Connector 3 pin XLR Splitter Section Maximum Level + 20dB Input Impedance 20 KOhms, Balanced Input Connector XLR Frequency Response 10Hz?20KHz ±0.5dB AC Power 100-120, 220-240 V AC, 8 VA Size 19?W x 6?D x 1??H, 482 x 155 x 44mm Weight 2.2 Kg (5 lbs)
Front Panel Controls Hi Impedance (Hi Z) insulated jack Input and Output connectors Level control with up to +15dB of Gain available Clip LED indicator Marker panels for labelling DI assigns Master Level controls Rear Panel Balanced XLR Outputs Individual Audio Ground Lift switches and status LEDs XLR and jack Master Outputs XLR Input for splitter Splitter/DI + Mixer mode switch AC input connector, with voltage switch and fuse. | Practical distributor with 1 input and 6 outputs
- Extends every mixer with additional outputs
- 1 stereo XLR input
- 6 stereo zone outputs (XLR)
- Each zone with level control and mono switch
- LED display of signal input and mono/stereo mode
- Rack installation with 1 U
- (19") 48.3 cm rack installation 1 U
Power supply: |
230 V AC, 50 Hz |
Power consumption: |
7 W |
S/N ratio: |
>69 dB |
THD: |
<0.2 % at 1 kHz |
Power connection: |
Mains input IEC connector (M) mounting version Power supply cord with safety plug (provided) |
Impedance: |
Input 45.1 kOhm
Output 125 Ohm |
Gain: |
15 dB |
Max. level: |
Output: +22 dB
Input: +9 dBV |
Color: |
Silver |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimension: |
Width: 48.3 cm
Depth: 12.6 cm
Height: 4.45 cm |
Weight: |
2.15 kg |
| Passive splitter box for microphone signals. One module has 4 channels. Each channel has an input, an output wired in parallel for passthrough of phantom power, and two splitter transformer-isolated outputs. All outputs are also decoupled via resistors.
- Each channel: Input: female XLR type
- Outputs: 1 parallel male XLR type, 2 transformer isolated male XLR type
- Nominal impedance for inputs/outputs: 200
- Max. input level: + 6 dBu
|
Reviews
There are no reviews yet.