| Content |
Work ESD 10K Automatic Voltage Regulator
It is a voltage regulator able to keep always constant the power supply in 220V
(or 110 V in the additional connector) when the voltage oscillates in a margin
from 140 to 250V ( 220 V input) or 60 to 130 V (110 V input) and connected to
a fix load of 10.000W. The need to keep a stable main voltage, above all for
systems or goods which performing depends on this value, it conserves these
regulators in an appreciated auxiliary device, when we have to supply mixers
effect appliances, etc. The incorporate 2 high brightness displays allow to read
clearly, working conditions, like input, output and main voltage. With the finality
to avoid parasite noise proceeding of the main switch, these units dispose of a
delay in the adjustable switching of 3 or 6 seconds, afterwards it runs in working
normal mode. In the protection section, both devices include protection against a
higher input voltage (255V), overheat and excess of output voltage. In these cases
the unit will switch off, transmitting an acoustic signal and a message in the display.
It disposes of a precise switch in the output voltage which allows to adjust this
parameter from a 1% to 3%.In the front panel, this unit disposes of a 63 A circuit breaker.
In the rear side are placed input/output connection CEE 32 A 3 pole. 1 additional
schucko output for 220 V and another for 110 V.
This unit is cooled by fan.
Technical Specifications:
Power supply: 140V- 250V AC.
Maximum joint load: 10000 VA.
Delay, selectable: 3 or 6 seconds .
Precision of output tension, selectable: 1% - 3%
Protections against:
Excessive temperature of 95 C
High input level
Overload
Dimensions: 460x305 x 260 mm
|
1 multiconnector input 8 schucko outputs
Specifications:
Power Input AC 230V~50/60Hz
Input Connector 16 pin ILME male multiconnector
Power Outlet 8xSchuko, 16A
Dimensions 345x150x102mm
Weight 3.2Kg
|
This is a 32 A three-phase power splitter with 3x 32A/400V input and 6 Schuko 16A/250V output.
Each Schuko is protected by a 16A circuit breaker and each phase can be read out by a 4-digit
voltmeter as well as 4-digit ammeter. Furthermore, a residual current circuit breacker is used for
protection against electronic shock under fault conditions. Also, a CEE-socket is provided for plugging
in power.
| Adam Hall Cables 87471
19" Power Strip 1U 8-way with switch
Mains Distribution Unit 19"/1 U
- Illuminated 2-pole switch on the front panel
- 8 mains outlets on the rear panel
- Black aluminium housing
- 54 mm deep
- 19 "angle can be mounted in four positions
Product type
19" rack mains socket strips
Number of outlets (Earthing contact / IEC 7/4)
8, Rotated 45°
Cable connector
angled, Earthing contact (CEE 7/7)
Cabinet material
Aluminium, Plastic
Other features
Illuminated on / off switch, Mounting brackets can be used in 4 positions
| Technical Drawing - 87470 [107,0 KB]
|
|
| - Professional compact mains distribution unit with four Schuko mains.
- Built in a stable aluminium housing
- 30 cm length (not 19“)
- The wider distance between the outlets allows using power adaptors side by side.
- Four possible mounting positions because of replaceable mounting clips.
- For mounting e.g. on the back wall or sidewalls inside of racks or on any other surface with screws (not included).
- Length of cable: 2 m
- Cross section of the inner conducters: 3 x 1,5mm²
- 16 A / 250V AC
|
|
Eurolite Board 10-ST w/10x safety-plug
10-fold switching panel
Fully cabled case with 10 safety-sockets
For 16 A safety-plug
10 switches with flash-buttons
10 fuseholders with 5 A
Power supply: 230 V AC, 50 Hz ~
Max. power output: 3680 W
Max. current: 16 A
Max. current/channel: 5 A
Output sockets: 10 safety power outlets
Fuses: F 6.3 A, 250 V
Dimensions (LxWxH): 135 x 485 x 135 mm
Weight: 3.3 kg |
Reviews
There are no reviews yet.