Content | Μετατροπέας Artnet σε DMX ( 2 universes ). Διαστάσεις: 86,3 x 42 x 67 mm.
Receiver / converter ArtNet-DMX and ArtNet nodes
2. Technical Data
● DMX receiver via Ethernet Plug & Play.
● Compatible with LightMouse LM-3E.
● Art-Net 2 Node.
Dimensions (Width x Height x Depth): 86 x 42 x 68 mm.
Power supply: 5V 500 mA
It is a receiver / converter ArtNet-DMX and ArtNet nodes, this, is able to interpret information from a DMX frame sent by the network and make it DMX information to control devices such as spotlights, moving heads, etc.
Its configuration is simple, just selecting with the rotary wheel the same number that is selected in the transmitter (LM 3E) to establish both communication and send out / receive the same DMX universe. The connection possibilities are huge, whether in a facility that needs to send a single universe from one location to another, send multiple universes, or even send a single universe to two different areas, using one transmitter and two receivers.
LM 3R2 is a ArtNet node with two DMX universes (1024 channels), is fully compatible with other devices, you can receive the two universes either by two emitters LM 3E or from a multiverse console via Artnet. Configuration will set which universe is the first, automatically, setting the following universe as the second to control.
In Art-NET mode, the device can be controlled by any software capable of generate Art-NET, i.e.
Chamsys MagicQ or using a DMX to ArtNet interface as LM 3E
In all cases, use the SubNet/Universe switches (7) to set the device according to the right connection
and the chosen universe to be controlle. |
- Professional 6-way DMX splitter / booster
- Chassis 1U 19" rack-mount enclosure
- 6 electrically isolated XLR (3-pin / 5-pin) outputs
- DMX status indicator per channel
- Power status indicator
- Switchable 120 Ohm terminating resistor for the DMX THRU output jack
- Front and rear rack-mount angle attachment options
The Cameo CLSB6D is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 6 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB6D and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
Product type
Other Lighting Accessories
Type
DMX splitter / booster
DMX inputs
2 (parallel)
DMX input connectors
XLR 3-pin male , XLR 5-pin male
DMX Thru Outputs
2 (parallel)
DMX Thru Output Connectors
XLR 3-pin female , XLR 5-pin female
DMX outputs
6
Controls
DMX Thru Terminator , Power On/Off
Indicators
6 x Power LED , 6 x Signal LED
Mains connector
IEC power connector
Operating voltage
transformer
Operating voltage
230 V AC, 50 Hz
Power consumption
15 W
Width
483 mm
Height
44 mm
Depth
160 mm
Weight
2,976 kg
Accessories (included)
Power cord |
Power supply: |
100-240 V AC, 50/60 Hz
12 V DC 1 A |
Power consumption: |
1 W |
Power connection: |
Mains input via 4-pin screw plug connector (M) mounting version power supply cord with AC adapter (provided) |
DMX input: |
2 x 3-pin XLR (M) mounting version |
DMX output: |
1 x 3-pin XLR (F) mounting version |
Use of brands: |
Built with NEUTRIK connector |
Dimensions: |
Width: 13 cm
Depth: 7 cm
Height: 4,1 cm |
Weight: |
500 g |
|
Work C 72 DMX
CD 72 DMX is a DMX to Analog signal converter suitable for 72 analog channels.
It converts DMX and MIDI signals into analog signals. It allows using an analog dimmer with DMX consoles, setting parameters like DMX start address channel, MIDI note selection, etc.
It also works as a chaser with adjustable speed to record and program scenes from a DMX console. With its Hold function, it provides memory against current failures that maintain the last DMX configuration.
C 72 DMX sends analog signals through SUB-25 connectors. Their input voltage can be set (from DC +10V, DC +15V or DC +20V) with DIP switches. Polarity can be switched too.
DMX to analog signal converter. Adjustable voltage level for outputs (DC 10, 15, 20 V). Voltage polarity selector. 72 channel chaser operating mode. Programmable DMX start address channel. Programmable chase speed. Memory against current failures. Main supply: 230 V AC 50 Hz. Dimensions (WxHxD): 483 x 44 x 120 mm. Weight: 2.3 kg.
| The Cameo CLSB83 is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 8 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB83 and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
The Cameo DMX splitter and booster is also available in 5-pin design (art. No CLSB85).
- Type: DMX 512 protocol
- DMX Inputs: 2 (parallel)
- DMX Input Connectors: 3-pin XLR male
- DMX Thru Outputs: 2 (parallel)
- DMX Thru Output Connectors: 3-pin XLR female
- DMX Outputs: 8 (electrically isolated)
- DMX Output Connectors: 3-pin XLR female
- Controls: Power On/Off, DMX Thru Terminator
- Indicators: 8 x Power LED, 8 x Signal LED
- Power Socket: IEC power socket
- Power Supply: transformer
- Operating Voltage: 230 V AC, 50 Hz
- Power Consumption (max.): 15 W
- Dimensions (W x H x D): 483 x 44 x 160 mm
- Accessories included in package: power cord
| The MA 2Port Node onPC allows the conversion of Ethernet data into DMX data and vice versa. In combination with grandMA2 onPC/grandMA onPC it is also possible to output DMX.
If used with grandMA2 onPC, the MA 2Port Node onPC outputs also 512 parameters of DMX (1,024 parameters as MA 2Port Node onPC PRO) and becomes a powerful show controller for smaller applications.
Also handy backup solutions for reduced budgets become possible. The MA 2Port Node onPC have integrated power supplies, but they also can be powered over Ethernet. Furthermore couplers and safety wires can be easily attached.
Two green LEDs will indicate if DMX traffic is in progress. Both, DMX LEDs and the display’s backlight, can be switched off remotely. The ‘Finder Functionality’ is a clever way to let the console indicate a selected node by flashing its backlight. In turn, a press of a button on the MA 2Port Node onPC will identify it on the console’s display.
All MA 2Port Nodes are fully integrated into the MA System. That means easy, comfortable configuration incl. in/out assignment of each node from any grandMA console or grandMA2 onPC/grandMA onPC. It’s also possible to use the nodes with other systems, because they speak MA-Net2, MA-Net and Art-Net, which can be set remotely.
The MA 2Port Nodes are also available as flush-mount versions (for EU and US in-wall boxes).
Dimensions 160 x 145 x 50 mm
Dimensions (inch) 6.3 x 5.7 x 1.9 inch
Net weight 1,1kg
Net weight (lbs) 2.3 lbs
PRICE WITHOUT V.A.T. 24% |
Reviews
There are no reviews yet.