| Content |
Work C 72 DMX
CD 72 DMX is a DMX to Analog signal converter suitable for 72 analog channels.
It converts DMX and MIDI signals into analog signals. It allows using an analog dimmer with DMX consoles, setting parameters like DMX start address channel, MIDI note selection, etc.
It also works as a chaser with adjustable speed to record and program scenes from a DMX console. With its Hold function, it provides memory against current failures that maintain the last DMX configuration.
C 72 DMX sends analog signals through SUB-25 connectors. Their input voltage can be set (from DC +10V, DC +15V or DC +20V) with DIP switches. Polarity can be switched too.
DMX to analog signal converter.
Adjustable voltage level for outputs (DC 10, 15, 20 V).
Voltage polarity selector.
72 channel chaser operating mode.
Programmable DMX start address channel.
Programmable chase speed.
Memory against current failures.
Main supply: 230 V AC 50 Hz.
Dimensions (WxHxD): 483 x 44 x 120 mm.
Weight: 2.3 kg.
| Standalone DMX Controller
- No computer required
- Compatible with any DMX device
- Up to 4 DMX universes (2048 channels, add-on required for U3+4)
- Up to 680 fixtures and beams
- Up to 50 fixture types
- Up to 5000 fixture properties (colour/gobo etc...)
- 8 Fixture groups
- 6 Projects
- 15000+ available fixtures (3500+ on the controller)
- DMX address
- Fixture order and group settings
- Use as DMX splitter with DMX universe mapping
- Colour FX module with 8 effect types and 16 definable colours
- Move FX module with 8 effect types
- Beam FX module with 8 effect types
- 6 Flash buttons for controlling Special FX, Strobe, Blinder, Speed, Blackout and Smoke
- Static colour palette with 10 user-defined colours per group and gradient control
- Static position palette with 5 user-defined positions per group with fade and fanning
- Gobo palette with 5 user-definable gobos per group
- 20 Nameable live edit buttons with flash trigger mode and 'park' function
- 100 Nameable presets for storing snapshots with hold and fade timings
- Preset playback cue list - all presets or per page of 20 presets
- Group and master dimming with encoder acceleration
- Group FLASH
- FULL and Blackout
- 16-Bit pan/tilt control:multi-beam LED bar control
- FX music pulse synchronisation from microphone or line-in
- FX BPM sync with Ableton Link
- OS2L or BPM Tap effect speed
- Phase, sequence, size, fade, fan and flick
- Live control of Move FX registration point
- Global FX speed and freeze control
- Map DMX IN with group dimmer and patch to output channels (add-on required)
- WLINK sync with another Wolfmix controller (add-on required)
- Fixture Builder
- Fixture calibration tool to limit the range of moving fixtures
- X-Y touch controlled positioning grid
- RGBW touch controlled colour picker
- 8-Step real-time sequencer to create beam and move FX
- Live view of DMX levels with override of default values and DMX channel tester
- Beam editor for overriding min and max values for created effects
- Calibration and RGB, white, amber, UV mixing with automatic translation of fixed colour wheel
- Automatic matching of similar gobos across different fixture types
- Time-controlled triggering of flash and preset buttons
- Fixture FLIP function for beam order reversal
- Fixture SPLIT function for splitting multi-FX bars
- Project and fixture backup with the WTOOLS app
- Offline 3D visualisation with Easy View & WTOOLS via USB (add-on required)
- Automatic restoration of the active project (no manual saving necessary)
- Import different fixture setups into the same project
Technical data:
- Housing: ABS plastic
- Powder-coated steel base plate with 100mm VESA
- Powder-coated, steel-reinforced back plate
- Screen: 4.3" colour TFT with tinted glass
- Capacitive touch
- Hardware: 220 Mhz CPU with ARM core, 8 MB RAM, 16 MB Flash
- Audio: Omnidirectional electret microphone
- 3.5 mm Jack line-in
- DMX: 2 x 3pin DMX OUT XLR connectors
- 1 x 5pin DMX OUT XLR connector
- 1 x 5pin DMX IN/OUT XLR connector with WLINK
- USB-B connector - 900ma required (USB3 rating)
- Dimensions (W x D x H): 195 x 220 x 62 mm
- Weight: 1070 g
|
- Professional 6-way DMX splitter / booster
- Chassis 1U 19" rack-mount enclosure
- 6 electrically isolated XLR (3-pin / 5-pin) outputs
- DMX status indicator per channel
- Power status indicator
- Switchable 120 Ohm terminating resistor for the DMX THRU output jack
- Front and rear rack-mount angle attachment options
The Cameo CLSB6D is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 6 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB6D and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
Product type
Other Lighting Accessories
Type
DMX splitter / booster
DMX inputs
2 (parallel)
DMX input connectors
XLR 3-pin male , XLR 5-pin male
DMX Thru Outputs
2 (parallel)
DMX Thru Output Connectors
XLR 3-pin female , XLR 5-pin female
DMX outputs
6
Controls
DMX Thru Terminator , Power On/Off
Indicators
6 x Power LED , 6 x Signal LED
Mains connector
IEC power connector
Operating voltage
transformer
Operating voltage
230 V AC, 50 Hz
Power consumption
15 W
Width
483 mm
Height
44 mm
Depth
160 mm
Weight
2,976 kg
Accessories (included)
Power cord | The Cameo CLSB83 is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 8 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB83 and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
The Cameo DMX splitter and booster is also available in 5-pin design (art. No CLSB85).
- Type: DMX 512 protocol
- DMX Inputs: 2 (parallel)
- DMX Input Connectors: 3-pin XLR male
- DMX Thru Outputs: 2 (parallel)
- DMX Thru Output Connectors: 3-pin XLR female
- DMX Outputs: 8 (electrically isolated)
- DMX Output Connectors: 3-pin XLR female
- Controls: Power On/Off, DMX Thru Terminator
- Indicators: 8 x Power LED, 8 x Signal LED
- Power Socket: IEC power socket
- Power Supply: transformer
- Operating Voltage: 230 V AC, 50 Hz
- Power Consumption (max.): 15 W
- Dimensions (W x H x D): 483 x 44 x 160 mm
- Accessories included in package: power cord
|
The Eurolite USB-DMX 512 interface combines very small dimensions with many functions due to the internal RISC-controller. This controller creates all DMX-signals so that the pc and the USB-port is not too busy enabling the parallel use of several DMX-universes.
Eurolite USB-DMX 512 Interface features:
- USB-DMX-Interface
- Interface between notebook or pc and DMX-devices
- Tested with the following DMX lighting control software: DMX-Configurator, FreeStyler, DMXControl
- Recommended system requirements: min. Pentium 3 processor 1GHz, 128 MB RAM
- Tested operating systems: Windows XP Home, Windows XP Professional, Windows Vista, Windows7
- Power supply: 5 V DC, 500 mA via USB
- Input: USB 1.1 / USB 2.0
- DMX-output: 512 channels
- DMX-512-connection: 3-pin XLR
|
NX DMX NX DMX is a USB powered 2 port DMX Node. As a member of the innovative ONYX platform from Obsidian Control Systems the NX DMX provides instant access to DMX In and Outputs as well as RDM communication. The device is plug and play and requires no drivers or additional configuration to integrate with ONYX. It is designed to work with any PC but also works with any ONYX console as a fast and affordable way to add two additional DMX ports.NX DMX supports ONYX on PC systems for up to four Universes without any dedicated license. When connected to an ONYX licensed PC or ONYX console the NX DMX is assignable to any one of 255 Universes.NX DMX allows for the full ONYX system to be used in many situations, from small events and tradeshows to clubs and churches. Many technicians utilize ONYX through the NX DMX as an affordable but powerful test station due to ONYX\' outstanding library support.
CONNECTION
2x DMX / RDM Universe In/Out: 5pin locking XLR USB In: USB 2.0 B
SPECIFICATION
Physical - Weight: 245g (0.6 lbs.)
- Length: 92 mm (3.7 in.)
- Width: 82 mm (3.3 in.)
- Height: 41mm (1.7 in.)
Electrical
- 5V over USB
- 100-240V nominal, 50/60 Hz
- Maximum current: 300 mA
|
Reviews
There are no reviews yet.