| Content | POWER SPLITTER
- Box connection phase separetor.
- Power Input: 380 V with connector CEE 3x16A (P+N+E).
- 6 schuko output with phase indicator.
- Dimensions: 220 x 150 x 102 mm.
- Weight: 1,8 kg. |
Electrical Specifications and Connections
Rated Current (A) 16 A
Flashover Voltage 250 V
Pins 3
Minimum Wire Size 0.75 mm²
Maximum Wire Size 1.5 mm²
Mechanical Specifications
Length (mm) 50 mm
Height (mm) 65 mm
Width (mm) 5 mm
Mounting Size 50 x 50 mm
Weight 0.06 kg
IP Rating IP44
Housing Plastic
Colour Blue
Product Properties
Pin Connection Screw Terminal
Contact Type Brass
|
1 Multiconnector input 8 CEE outputs |
1 multiconnector input 8 schucko outputs
Specifications:
Power Input AC 230V~50/60Hz
Input Connector 16 pin ILME male multiconnector
Power Outlet 8xSchuko, 16A
Dimensions 345x150x102mm
Weight 3.2Kg
|
Zero88 Switch 6 Socapex DMX 6 Channels Digital Switcher
Cost effective 19" dimmer
The Rack 6 is an economical choice for those wanting a rack mount DMX dimmer. Housed in a compact 2U unit the Rack 6 offers users six 10 amp circuits of dimming control. Using the latest electronic and electrical designs the Rack 6 offers real value for money. All operator controls are available through a simple, intuitive interface.
The Rack 6 is not limited in features however. Offering 12 memories, a preheat per channel, three dimmer curves and Chilli-Net compatibility the Rack 6 offers users sophistication not usually found in a dimmer in this price range.
With a range of socket options, CE certification and a three year warranty the Rack 6 is the ideal choice for users looking for a cost effective touring dimmer.
The Switch 6 is physically identical to the Rack 6, except that each channel is controlled by a heavy duty relay, instead of a dimming circuit. Ideal for switching non-dimmable loads, the Switch 6 is available with the same socket options as the Rack 6.
| Features |
- 3 dimmer curves (normal, linear, switch)
- 12 Memories
- Preheat per channel
- International socket options
- 6 x 10 Amps
- MCB per channel
- Advanced heatsink and fan cooling
- DMX addressing via user interface
|
- 19"
- Built in termination circuit for DMX
- ChilliNet enabled
- RDM hardware ready
- Dimensions - 88mm x 483mm x 360mm
- Weight - 8.0kg
| |
Work ESD 10K Automatic Voltage Regulator
It is a voltage regulator able to keep always constant the power supply in 220V
(or 110 V in the additional connector) when the voltage oscillates in a margin
from 140 to 250V ( 220 V input) or 60 to 130 V (110 V input) and connected to
a fix load of 10.000W. The need to keep a stable main voltage, above all for
systems or goods which performing depends on this value, it conserves these
regulators in an appreciated auxiliary device, when we have to supply mixers
effect appliances, etc. The incorporate 2 high brightness displays allow to read
clearly, working conditions, like input, output and main voltage. With the finality
to avoid parasite noise proceeding of the main switch, these units dispose of a
delay in the adjustable switching of 3 or 6 seconds, afterwards it runs in working
normal mode. In the protection section, both devices include protection against a
higher input voltage (255V), overheat and excess of output voltage. In these cases
the unit will switch off, transmitting an acoustic signal and a message in the display.
It disposes of a precise switch in the output voltage which allows to adjust this
parameter from a 1% to 3%.In the front panel, this unit disposes of a 63 A circuit breaker.
In the rear side are placed input/output connection CEE 32 A 3 pole. 1 additional
schucko output for 220 V and another for 110 V.
This unit is cooled by fan.
Technical Specifications:
Power supply: 140V- 250V AC.
Maximum joint load: 10000 VA.
Delay, selectable: 3 or 6 seconds .
Precision of output tension, selectable: 1% - 3%
Protections against:
Excessive temperature of 95 C
High input level
Overload
Dimensions: 460x305 x 260 mm
|
Reviews
There are no reviews yet.