Content |
The SW10 STUDIO subwoofer has been designed specifically for optimum matching with the MSP series powered monitor speakers. Combined with MSP7 STUDIO or MSP5 STUDIO speakers in a stereo of surround system it can provide a seamlessly extended low end for accurate ultra wide range monitoring. A comprehensive selection of inputs and outputs as well as a phase switch and continuous high-cut and level controls make it easy to achieve optimum performance in any room and system. Whether you're simply mixing basic stereo programs or authoring DVD audio in full surround, MSP STUDIO series speakers plus an SW10 STUDIO will give you the ultimate monitoring experience.
GENERAL Type Powered Subwoofer
Crossover Frequency -
Overall Frequency Response 25Hz - 150Hz (-10dB)
Maximum Output Level 111dB, 1 m on Axis
Dimensions (W x H x D) 328 x 459 x 476 mm
Weight 26.5 kg
Magnetic Shielding Yes (Non-covered type)
SPEAKER SECTION Components LF 10" cone
HF -
Enclosure Type Bass-Reflex
Material MDF
AMPLIFIER SECTION Output Power * LF 180W
f = 100Hz, THD = 1%, RL = 8O
HF -
S/N, IHF-A filter > 100dB, LEVEL = Max
Input Sensitivity XLR-3-31 +4 dBu, LEVEL = Center
-6 dBu, LEVEL = Max
PHONE -
Input Connectors, Impedance XLR-3-31 (balanced), 10 kO
Output Connectors XLR-3-32 x 3 (balanced),
parallel connection with Input
Controls LEVEL control Center Click VR
(Min = -8 Attenuation)
LOW CUT switch -
HIGH TRIM -
LOW TRIM -
POWER SWITCH on/off
PHASE SWITCH Normal/Reverse
LPF control 40-120 Hz, 80 Hz at Center Click
Indicators LED Green: Power On
Red: Clipping
Power Consumption 160W
* These specifications apply to rated power supplies of 100, 120, 230 and 240 V.
* Specifications and appearance subject to change without notice.
|
The Sub6 is a large volume cabinet design, equipped with an 11" woofer and a rear laminar port. This configuration guarantees bass linearity whatever the intended SPL. The control board is extremely versatile, with connectivity which allows a 2.1, 2.2 and multichannel use via the L/R inputs and outputs and the LFE. The numerous settings such as the high-pass crossover dedicated to monitors, the adjustable phase and level control provide optimum coupling with the Solo6 Be and the Twin6 Be monitors. And finally, a small, but important point: the footswitch input. It enables one to connect a pedal to deactivate the subwoofer and the high-pass crossovers on the outputs that supply the monitors. This simplifies and greatly improves control during the different stages in monitoring.
Specifications Frequency response : | 30Hz - 250Hz | Maximum SPL : | 116dB SPL (peak @ 1m) |
Input :
|
Right, left, LFE
Electronically balanced, 10 kOhms
XLR 3 points socket
Adjustable
| Outputs (towards speakers) : | Type/Impedance: Electronically balanced / 50 Ohms - Connector: XLR 3 points plug |
Amplification :
|
350W rms, BASH® technology
|
Signal internal treatment :
|
Subwoofer section: Mono right/left summation
LFE + mono low-pass
24dB/octave
Phase adjustment
Polarity selection switch
Switch high-pass filter, cut-off frequency selection
Speaker section : 24 dB / octave
|
Electric supply :
|
Local supply wire: 230V (1.6A fuse)
or 115V (3.5A fuse)
Connection: removable IEC supply wire
|
Visualization and control :
|
Adjustable subwoofer level
Low-pass cut-off frequency setting
Phase adjustment
Polarity adjustment
Subwoofer switch (mute)
2.1 "Bypass" (external remote contol)
High-pass frequency selection
Releasable high-pass
| warning light : | Power on LED, Subwoofer switch (mute), Released high-pass |
Electric supply :
|
Local supply wire: 230V (1.6A fuse)
or 115V (3.5A fuse)
Connection: removable IEC supply wire
| Subwoofer : | 11W7670, 10-5/8" (27cm) Focal "W" composite sandwich cone driver | Box : | 7-1/2" (19mm) MDF panels |
Finish :
|
Dark red natural veneering side panels, black body.
| Dimensions (HxWxD) : | 14-15/16 x 13-9/16 x 17-5/16 " (380 x 344 x 440mm) | Weight : | 50.7lb (23kg) |
| To hear what's really going on at the bottom of your mixes, you need a subwoofer that speaks the truth. The TemblorTM T10 lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls not normally available in this price range.
Main components - 10-inch glass-composite low-frequency transducer
- Front-firing, bass-reflex acoustic port
Controls and filters - Input gain control (-30 dB to +6 dB, continuously variable)
- Continuously variable lowpass filter (50 Hz to 130 Hz)
- Built-in crossover
- Switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the T10 outputs to the main monitors
- Momentary footswitch (included) bypasses the subwoofer, highpass filter, and Sub Out
- Polarity invert and ground-lift switch
Power and safety - 250 watt, Class AB amplification
- Internal damping and heat sink
- Integrated, gravity-calibrated rubber feet for stable placement
Inputs and outputs - Left and right, balanced XLR and ¼" TRS and unbalanced RCA main inputs
- Left and right balanced XLR and ¼" TRS outputs
- XLR subwoofer output for connecting a second T10
Inputs |
| 2- Balanced XLR |
| 2- Balanced ¼" TRS |
| 2- Unbalanced RCA | | | Outputs |
| 2- Balanced XLR (full range with 80 Hz HPF option) |
| 2- Balanced ¼" TRS (full range with 80 Hz HPF option) |
| 1- Balanced XLR (Sub Out) | Performance | Frequency Response | 20 Hz - 200 Hz | Low Pass Filter Frequency | 50 - 130 Hz (variable) | Signal-to-Noise Ratio | >98 dB | THD | 0.019% @ power | |
The Genelec 7073A active subwoofer is a powerful and precise bass reproduction tool for large Surround Sound or Stereo installations. Its 19 Hz lower cut-off frequency and 124 dB sound pressure output capability are sufficient to handle the most demanding high SPL applications.
All electronics are integrated into the subwoofer cabinet: active crossover filters, driver overload protection circuits and power amplifiers.
The built-in bass management unit has six signal input and output channels (L/C/R Front and L/C/R Rear), LFE input and summed signal output connectors, providing great flexibility and easy connection.
| 124 dB | | Main 19 - 85 Hz (± 3 dB)
LFE 19 - 120 Hz (± 3 dB) | | 0 to -270° (90° steps) | | 4 x 12“ | | 1000 W | | H x W x D 524 x 1440 x 558 mm | | 120 Kg (265 lb) | | 6.1 XLR analog in
6 x XLR analog out
1 x XLR Link out |
|
Dynaudio 9S, Active Subwoofer 24 cm (9.5“) Woofer, 300 Watt Class-D Amp, Frequency Range: 22 Hz - 175 kHz (+/- 3dB), 37 mm front baffle, Master/Slave Function, adjustable Lowpass Filter, Connections: XLR, SAT output with defeat-able highpass filter, Auto On/Off Function.
Dimensions: 266 x 320 x 276 mm, Weight: 10.5 kg
Type: |
Studio Monitor Subwoofer |
Woofer: |
9.5" long-throw MSP |
Amplifiers Power: |
300W Class-D |
Input/Output Plugs: |
XLR Balanced |
Frequency Response: |
22-250Hz +/- 3dB |
Dimensions (W x H x D): |
266 x 276 x 320 mm |
Weight: |
10.5 kg |
|
Genelec SE7261A Active DSP Subwoofer brings the flexibility and accuracy of room response equalization to smaller production environment. At the heart of the Genelec SETM (Small Environment) DSP loudspeaker system is the SE7261A DSP subwoofer with DSP processing.
The SE7261A DSP subwoofer provides all necessary network connections to the host computer and supply extensive DSP resources through its eight AES/EBU high-passed channels to the 8130A active loudspeakers.
The proprietary GLM.SETMsoftware kit includes a measurement microphone, AutoCalTM function and other key features of the standard GLM software.
| 108 dB | | Main 19 - 100 Hz (± 3 dB)
LFE 19 - 120 Hz (± 3 dB) | | GLM tone controls | | 10“ | | 120 W | | H x W x D 527 x 462 x 363 mm | | 27 Kg (59 lb) | | 4 x XLR digital in
4 x XLR digital out
(8 channels AES/EBU) |
|
Reviews
There are no reviews yet.