Content | Uses a system of interchangeable input capsules that can be swapped out as easily as the lens of a camera
Includes detachable X/Y capsule (XYH-5) with extended signal capacity and shockmounted mics for reduced handling noise
Compatible with all Zoom input capsules
Four-track simultaneous recording
Large backlit LCD display
Records directly to SD and SDHC cards up to 32GB
Up to 24-bit/96kHz audio in BWF-compliant WAV or a variety of MP3 formats
Two mic/line inputs with XLR/TRS combo connectors, each with selectable phantom power and -20dB pad
Analog-style gain controls for each input
Protective "roll-bar" type covers prevent accidental movement of gain controls
Plug-in power (2.5 volts)
Built-in effects, including low-cut filtering, compression and limiting
Chromatic tuner and metronome
Auto-record, Pre-record and Backup-record functions mean that you'll never miss that perfect take
MS decoding
Multitrack to stereo internal mixdown
Normalize, Divide and Trim editing
Voice memo and up to 99 marks per recording
A/B loop playback
Variable playback speed and variable pitch without affecting playback speed
Multichannel and stereo USB audio interface for PC/Mac/iPad with loop back function
Mountable to DSLR or camcorder with optional HS-01 Hot Shoe Mount adapter
Uses two standard AA alkaline or NiMH rechargeable batteries
Over 15 hours of operation with alkaline batteries
GENERAL
Recording media:
SD card: 16MB to 2GB , SDHC card: 4GB to 32GB
Display:
Backlit LCD (128 x 64 pixels)
INPUTS
INPUTS L/R [XYH-5 X/Y mic]:
Mic type: Unidirectional
Sensitivity: -45 dB, 1 kHz at 1 Pa
Input gain: -∞ to 52 dB
Max sound pressure input: 140 dB SPL
MIC/LINE IN :
Connector: 1/8" stereo mini jack
Input gain: - ∞ to 52 dB
Input impedance: 2 k Ω or more
Plug-in power: 2.5V supported
Backup recording: -12dB lower than set L/R input gain
INPUTS 1/2:
Connectors: XLR / TRS combo jacks
(XLR: Pin 2 hot / TRS: Tip hot)
Input gain (PAD OFF): -∞ to 55.0 dB
Input gain (PAD ON): -∞ to 35.0 dB
Input impedance: 1.8 k Ω or more
Max input level: +22 dBu (PAD ON)
Phantom power: +12V /+24V /+48V
Equivalent Input Noise (EIN): -120 dBu or less
OUTPUTS
LINE OUT :
Connector: 1/8" stereo mini jack
Rated output level: -10 dBm
Output load impedance: 10k Ω or more
PHONE OUT :
Connector: 1/8" stereo mini jack
Output Level: 20 W +20 W into 32 Ω load
Built-in speaker:
400mw 8 Ω mono
RECORDING FORMATS
STEREO MODE:
WAV (BWF-compliant)
Sampling frequency: 44.1/48/96 kHz
Bit rate: 16/24 (Stereo)
Maximum simultaneous recording tracks: 2
MP3
Sampling frequency: 44.1kHz
Bit rate: 48/56/64/80/96/112/32/160/192/224/256/320kbps
MULTITRACK MODE:
WAV (BWF-compliant)
Sampling frequency: 44.1/48 kHz
Bit rate: 16/24 (Mono/Stereo)
Maximum simultaneous recording tracks: 6 (L/R + INPUT 1/2 + L/R backup)
USB
Mass Storage Class operation:
Class: USB 2.0 High Speed
Audio Interface operation: Multitrack mode:
Class: USB 2.0 High Speed
Sampling frequency: 44.1/48kHz
Bit rate: 16/24 bit
Inputs / Outputs: 4 / 2
Audio Interface operation: Stereo mode:
Class: USB 2.0 Full Speed
Sampling frequency: 44.1/48kHz
Bit rate: 16 bit
Inputs / Outputs: 2 / 2
USB bus powered operation possible
(iPad operation supported in Stereo mode only)
POWER REQUIREMENTS
AA size (LR6) battery x 2
AC adapter: AD-17 (DC5V/1A/USB-type) (optional)
USB bus power | Recorder section
Number of tracks:
2 tracks
2 tracks simultaneous playback
2 tracks simultaneous recording
Recording formats:
Compressed audio format
MP2 format (extension .mp2)
48 kHz@128, 192, 256, 320 kbps
MP3 format (extension .mp3)
44.1 kHz@128, 192, 256, 320 kbps
PCM audio format
WAV format (extension .wav), BWF compliant
44.1 kHz @ 16/24-bit, 48 kHz @ 16/24-bit
88.2 kHz @ 24-bit, 96 kHz @ 24-bit
176.4 kHz @ 24-bit, 192 kHz @ 24-bit
1-bit audio format
2.8 MHz @ 1-bit
DSDIFF format (extension .dff), DSF (extension .dsf), WSD (extension .wsd)
Recording Time:
Maximum 6 hours @ 44.1 kHz/16-bit (for 4GB memory card)
Maximum continuous recording 6 hours
Number of projects:
Recognizes a maximum of 400 projects of each date folder
Mark points:
100 points per project *No mark names
USB functionality:
Connect to computer via USB 2.0, usable as FAT32 USB removable drive
Song editing:
Rename, Delete, Protect
Tuner
Temperament:
Equal temperament, chromatic tuner
Range (sine wave):
27.50 Hz – 1,318.5 Hz (A0 - E6)
Reference pitch:
A = 435 – 445 Hz
Memory Card (SD)
Supported cards:
SD and SDHC cards with a capacity of 512MB-32GB
(SDHC card of class 4 or higher recommended)
General
Display:
128 x 128 pixel LCD with backlight
Power supply:
AA/LR6 alkaline battery x 2;
AA nickel-metal hydride battery x 2;
USB bus power
Power consumption:
1.5W
Dimensions:
(W x D x H): 2.52" x 4.72" x 0.9“
Weight:
4.94 oz. (not including a memory card and batteries)
Main specifications
Frequency response:
20 Hz – 20 kHz ±1.5 dB (MP2/MP3)
10 Hz – 20 kHz ±1.5 dB @Fs44.1 kHz/48 kHz
10 Hz – 40 kHz ±1.5 dB @Fs88.2 kHz/96 kHz/176.4 kHz/192 kHz
10 Hz – 100 kHz (1-bit)
S/N:
90 dB (typical) @IHF-A
THD+N:
0.018% (typical) 20 Hz – 20 kHz
A/D conversion:
2.8224 MHz (1-bit), 24-bit (PCM)
D/A conversion:
2.8224 MHz (1-bit), 24-bit (PCM)
Mic
Connector:
3.5 mm stereo mini phone jack (switchable to Plug-in-Power)
Input impedance:
10k ohms
Nominal level:
-39 dBV
Maximum level:
-27 dBV
Line In
Connector:
3.5 mm stereo mini phone jack
Input impedance:
75k ohms
Nominal level:
-10 dBV
Maximum level:
+2 dBV
Phones
Connector:
3.5 mm stereo mini phone jack
Maximum level:
20 mW+20 mW @ 16 ohms
USB
Connector:
Type mini-B
Format:
USB 2.0 compliant, USB mass storage class
Supported operating systems:
Windows 2000, or later; Mac OS X 10.4 or later
Included items
Install CD (“AudioGate” audio file conversion application)
AudioGate (v2.0) System Requirements
Windows
Supported OS:
Microsoft Windows XP Home Edition/Professional Edition Service Pack 3 or later
Microsoft Windows Vista Service Pack 2 or later
Microsoft Windows 7
Supported Computers:
Processor: Intel Pentium III/1GHz or faster
Memory: 256MB or larger (512 or larger recommended)
Hardware: A USB port that meets the operating requirements of Windows;
A writable CD/DVD drive is required in order to create audio CDs or DSD discs.
Mac OS X
Supported OS:
Mac OS X 10.4 or later
Supported Computers:
Processor:Apple G4/800MHz or faster (Intel-based Mac recommended)
Memory: 256MB or larger (512 or larger recommended)
Hardware: A USB port that meets the operating requirements of Mac OS X;
A writable CD/DVD drive is required in order to create audio CDs or DSD discs. |
Recorder Section: | | Number of Tracks: | | 2 tracks, 2-track recording/playback simultaneously
| | Recording Formats: | | 1-bit audio formats - DSDIFF, DSF, WSD: 2.8224 MHz @ 1-bit, 5.6448 MHz @ 1-bit
PCM audio formats - WAV, BWF: 44.1 kHz @ 16/24-bit, 48 kHz @ 16/24-bit, 88.2 kHz @ 24-bit, 96 kHz @ 24-bit, 176.4 kHz @ 24-bit, 192 kHz @ 24-bit
MP3 format - playback only
44.1kHz or 48kHz/32kbps-320kbps
| | Internal Hard Disk Drive: | | 40 GB
| | Recording Time: | | Max Approx. 60 Hours (44.1 kHz @ 16-bit, 2-track)
| | Number of Projects: | | Recognizes a maximum of 200 for each format, max 1,000 projects
| | Mark Points: | | 100 points per a song (no mark name)
| | USB Functions: | | USB 2.0 supported, ability to use as FAT32 external USB drive
| | Song Editing: | | Rename, Delete, Protect
|
General: | | Display: | | 160 x 104 dots LCD with backlight
| | Dimensions: | | 192(W) x 170(D) x 56(H) mm/7.56“(W) x 6.69“(D) x 2.20“(H)
| | Weight: | | 1.0 kg/2.20 lbs. (without batteries)
| | Power Supply: | | Eight AA batteries (sold separately), Oxyride batteries, charged nickel metal-hydride batteries, or AC Adapter model � (adapter) 500405015300 & (3 prong cable) 600007300/KA310
12V 500mA Center Pin (+);
| | Current Consumption: | | 7 W
| | Accessories: | | AC Adapter; Carrying Bag; CD-ROM (“AudioGate" Audio File Conversion Software)
|
Principal Specifications: | | Frequency Response: | | 10Hz ~ 20kHz ±1dB @ Fs44.1kHz, 10Hz ~ 40kHz ±1dB @ Fs88.2kHz/96kHz/176.4kHz/192kHz, 10Hz ~ 100kHz (1 bit)
| | S/N: | | 96 dB (typical) @ IHF-A INPUT-OUTPUT
| | THD+N: | | 0.008% (typical) 20 kHz-LP
| | A/D Conversion: | | 2.8224 MHz/5.6448 MHz (1-bit), 24-bit (PCM)
| | D/A Conversion: | | 2.8224 MHz/5.6448 MHz (1-bit), 24-bit (PCM)
|
INPUT L-R: | | Connectors: | | XLR-3-31 type / 1/4" TRS phone jack (balanced)
Phantom power: 48V/10mA per channel, on/off switch
| | Input Impedance: | | 4.5 k Ohm (XLR-3-31), 68 k Ohm (TRS phone, Line)
| | Nominal Level: | | - 60 dBu - - 28 dBu, XLR (balanced), - 26 dBu - + 4 dBu, 1/4" TRS phone (balanced), - 26 dBV - - 6 dBV, 1/4" TRS phone (Unbalanced)
| | Maximum: | | 16 dBu, XLR (balanced), + 16 dBu, 1/4" TRS phone (balanced), + 6 dBV, 1/4" TRS phone (Unbalanced)
|
OUTPUT L-R (Unbalanced/Balanced): | | Connectors: | | RCA (Unbalanced)/XLR-3-32 type (balanced)
| | Nominal Level: | | 6 dBV/+ 4 dBu
| | Maximum Level: | | + 6 dBV/+ 16 dBu
| | Load Impedance: | | 47 k Ohm or greater/600 k Ohm or greater
|
PHONES: | | Connector: | | 1/4" stereo phone jack
| | Load Impedance: | | 16 k Ohm or greater
| | Maximum Level: | | 50 mW + 50 mW @ 32 k Ohm
|
USB: | | Connector: | | Type B
| | Format: | | USB 2.0 High-Speed device, USB mass storage class
| | Supported OS: | | Windows Me, 2000 or later, Mac OS 9.0.4 or later*1
*1With Intel based Macs, you must turn on the unit after making USB connection.
|
Included Items: | | AC adaptor (also operates as charger), carry bag, CD-ROM (�AudioGate� audio file conversion application)
|
AudioGate System Requirement: | | Supported OS: | | Windows XP Home Edition/Professional Edition (Service Pack 1 or later), Mac OS X 10.3.9 or later
| | CPU: | | [Windows] Intel Pentium III/1 GHz or faster [Macintosh] Apple G4/800 MHz or faster (Intel-based Mac supported)
| | Memory: | | 256 MB or larger (512 MB or larger recommended)
| | *“DSD" is a registered trademark
*Logos, product names and company names are their tradmarks or registered trademarks |
|
The new Fostex FR-2 has been designed specifically for location sound recording; high quality sound effects acquisition; TV & radio documentary; in fact any application where quality audio recording is required.
With excellent quality (up to 24-bit / 192KHz recording - a first for a CF recorder), huge feature list and a cost-effective price point, the FR-2 offers users of portable DAT and other formats the opportunity to make the switch to a more flexible, higher quality audio acquisition machine without sacrificing features.
- Recording industry standard, PC-compatible BWF files (stereo/mono) on a FAT32 media format
- Up to 24-bit/192kHz uncompressed recording
- Includes a unique 22.05kHz sampling frequency setting for extended recording
- Records to both Type I & II CompactFlash cards and PCMCIA 1.8” hard disk drives*1
- Fostexʼs "File per Take” system with auto scene & take naming/increment
- Two balanced XLR microphone inputs with switchable phantom power and top quality, high headroom mic pre-amps
- 132 x 64 dot matrix LCD screen for ease of use & high visibility in the field
- Uses AA-sized rechargeable NiMH batteries which are widely available due to the popularity of digital cameras. 8 AA cells will provide approximately 2.5 hours operation when recording to a CF card
- Easy file transfer to PC/Mac via PCMCIA, CF adaptor or standard on-board USB connection for data editing and/or backup*2
- Quick and easy on-board file naming or via external keyboard through standard USB keyboard port
- “Pre-record” loop buffer of approximately 10 seconds*3
- Easy software update via CF or PCMCIA card with downloads from the internet
- Optional timecode generator / reader card
Notes
*1 May require software update for PCMCIA HD operation
*2 Complies with Windows ME/2000/XP, Mac OS 10.2 or higher
*3 Varies depending on sampling frequency“
- GENERAL
Recording Media CompactFlash card, PCMCIA HD
Recording Format BWF
Number of Channels Stereo / Mono
Sampling Frequency 22.05 / 44.1 / 48 / 88.2 / 96 / 176.4 / 192kHz
Quantization 16 bit (22.05 - 48kHz), 24 bit (44.1 - 192kHz)
- PHYSICAL
Power Requirement 8 x AA type dry cell (NiMH recommended)
AC adaptor (optional)
DC 12V
Power Consumption approx. 5W
Dimension 250(W) x 77(H) x 220(D) mm
Weight 1.5kg (w/out battery)
- PERFORMANCE
R/P Frequency Response 20Hz to 10kHz +/-1dB (fs: 22.05kHz)
20Hz to 20kHz +/-1dB (fs: 44.1 / 48kHz)
20Hz to 40kHz +/-2dB (fs: 88.2 / 96kHz)
20Hz to 80kHz +/-3dB (fs: 176.4 / 192kHz)
S/N (ADC-DAC, 24-bit, ref: -20dB, fs:48kHz)
Line (input gain: +4dBu): 100dB (typical)
Mic: (input gain: -60dBu): 87dB (typical)
Dynamic Range 100dB (ADC-DAC, 24bit, ref:-20dB, fs:48kHz) typical
T.H.D. (ADC-DAC, 24-bit, ref:-20dB, fs:48kHz)
Line (input gain: +4dBu): Less than 0.005% (at 1kHz, -1dB typical)
Mic (input gain: -60dBu): Less than 0.008% (at 1kHz, -1dB typical)
Power Life approx. 2 hours 30 min. (8 x AA NiMH type/2300mAH)
- INPUT / OUTPUT CONNECTORS
ANALOG AUDIO INPUT L/R
Connector XLR-3-31 type (Pin2: Hot)
Line Input Impedance : More than 6k ohm
Reference Input Level +4dBu
Maximum Input Level +24dBu (Trim: +4dBu, at the prefader stage)
MIC
Input Impedance More than 6k ohm
Input Level -60dBu
Maximum Input Level -40dBu (Trim: +4dBu, at the prefader stage)
Phantom Power P48
ANALOG AUDIO OUTPUT L(Mono)/R
Connector RCA pin type
Output Load Impedance more than 10k ohm
Nominal Output Level +4dBu
HEADPHONE OUTPUT 50 + 50mW (32 ohm)
Max Speaker Output Level 1W
DIGITAL INPUT/OUTPUT (except for 176.4, 192kHz)
Connector XLR
Input Format S/P DIF / AES/EBU automatic
Output Format S/P DIF / AES/EBU switchable
USB x 2 (keyboard / PC only)
TIMECODE CARD (OPTIONAL, T.B.A.)
LTC Input/Output LEMO
Frame Rate 23.976/24/25/29.97DF/29.97ND/30DF/30ND
Gen Mode 24H RUN / REC RUN / FREE RUN / EXT RUN
|
Features at a glance - Supports Sennheiser wireless system mics and transmitters (DR-10CS)
- Supports Shure wireless system mics and transmitters (DR-10CH, DR-10CS with optional AK-DR10CH panel)
- Supports Sony/RAMSA wireless system mics and transmitters (DR-10CS/DR-10CH with optional AK-DR10CR panel)
Note: The Sony/RAMSA panel has a sliding switch to allow proper wiring configuration - 48kHz/24-bit linear PCM mono recording
- WAV files (compatible with BWF format)
- Media: microSD/SDHC cards (supports 32GB capacities)
- Sliding record switch and hold function to prevent misoperation during recording
- Dual recording function
- automatic file closing function to prevent the loss of already recorded data
- High/Mid/Low recording level settings
- Low-cut filter
- Limiter
- Automatic level function
- With a built-in clock function, supports BWF files that can have time information added - convenient for editing and searching
- Time track incrementing function can create new files at regular intervals (every 15 minutes) during recording
- Playback function allows recorded data to be checked immediately
- Headphone output
- Easy-to-read organic EL display
- micro USB B port enables easy data exchange with computers
- Records at least 10 hours on a single AAA battery * using alkaline batteries (EVOLTA)
- Unit settings can be created and transferred as a computer text file
- Settings can be transferred between DR-10C units using the infrared transmission function
- Firmware can be updated using a microSD card
- Belt clip included
- Silicon band that can be used to attach the unit to a transmitter included
- Custom case for storing the unit and accessories included
- RoHS-compliant product
| |
Reviews
There are no reviews yet.