Tube-buffered DI-Box DI-1000 The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the […]
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur – but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz – 20 kHz (-0,1 dB) 5 Hz – 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A – military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak
Βάρος
0.60 kg
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.
Κάνετε την πρώτη αξιολόγηση για το προϊόν: “ALPHATON DI 1000 TUBE DI BOX” Ακύρωση απάντησης
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur - but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz - 20 kHz (-0,1 dB) 5 Hz - 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A - military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak
Παθητικό DI box με ground lift, αναστροφή φάσης, έξοδους XLR και καρφί 1/4'' (thru), pad 3 θέσεων στην είσοδο για σήματα επιπέδου instrument/line/speaker
Active DI box in a sturdy metal housing (aluminium/steel) with protective corners, silver-blue metallic, internal battery (9 V flashes during operation) is switched off automatically when phantom power is used (LED permanently illuminated),
extremely low battery consumption. Battery: 9 V block (not included).
Product type DI Boxes Channels 1 Inputs 2 Input connectors 6.3 mm Jack , XLR Max. input level + 10 / + 30 dBu dBu Input impedance 1 M Ohm(s) Outputs 1 THRU outputs/channel 1 Output connectors XLR Frequency response 20 - 20.000 Hz THDIndicators Power Controls ground lift , Power Operating voltage +48 V phantom power , 9 V block Cabinet material metal Cabinet surface painted Width 135 mm Depth 128 mm Height 53 mm Weight 0,645 kg
Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm.
Little brother of the LH-055 DI Box. Sturdy housing, solid workmanship at an unbeatable price.
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal (e.g. to a guitar amplifier) 1 low-impedance output (XLR) Black housing
Passive 1-channel DI box, black
1 high-impedance signal input, 6.3 mm jack
1 low-impedance XLR output
6.35 mm jack input, and output
Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
Switchable input attenuation: 0 dB, -20 dB, -40 dB
Rugged black metal housing
Package contents
1 x device, 1 x user manual
Frequency range:
15 - 30000 Hz
S/N ratio:
>95 dB
Impedance:
Input: 50 kOhm
Output: 600 Ohm
Input attenuation:
0 dB, -20 dB, -40 dB; switchable
Control elements:
Groundlift selector
Connections:
Input: 1 x 6.3 mm plug (unbal.)
Link: 1 x 6.3 mm plug (unbal.)
Output: line via 1 x 3-pin XLR
Dimensions:
Width: 12,7 cm
Depth: 7,4 cm
Height: 4,5 cm
Weight:
440 g
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.