Content |
Ashly presents the PQX series parametric equalizers. Like graphic equalizers,
parametrics allow you to boost or cut selected frequencies. However, parametric
equalizers also allow exact adjustment of the frequency and bandwidth of each
band, resulting in very precise control of frequency response. The amplitude,
center frequency, and bandwidth are the "parameters" for each equalizer band
and the term "Parametric" refers to the ability to adjust all of these characteristics
independently
The Ashly PQX series equalizers are a third generation design including many
refinements on our original PQ models. Lower noise, greater headroom, additional
filters, full 20Hz -20KHz range on all parametric filters and additional connector
types are the result.
The heart of the PQX equalizers is a unique bandpass filter circuit. Basically a
“state-variable" type, this filter is trimmed and optimized to provide excellent
transient response and a wide range of frequency and bandwidth adjustment.
Each filter can be tuned over a 100:1 frequency range (about 6.6 octaves) and
a 70:1 bandwidth range with no more than a 2 dB amplitude error at center frequency.
At its sharpest setting, the filter has a "Q" of about 35 and generates a response curve
with 3 dB points only 1/20 octave apart, making feedback control possible with no
audible side effects. Each filter is placed in the feedback loop of a summing amplifier
to produce the desired frequency response. Since a separate summing amplifier is used
for each band, no interaction between bands occurs. After twenty years of refinement,
the Ashly parametrics are the most powerful equalization tool available. They especially
excel in control of resonance and feedback yet also provide smoother broadband tone
shaping than Graphic equalizers.
|
5 Fully parametric bands |
|
Parametric filters tunable from 20Hz to 20KHz |
|
Very low hum and noise design |
|
Adjustable bandwidth from 3 1/3 to 1/20 of an octave |
|
True reciprocal curves |
|
Master and individual band in/out bypass switching |
|
Balanced Inputs and Outputs |
|
XLR, 1/4" TRS and barrierstrip audio connections |
|
Five Year Warranty | |
Νέα έκδοση S γραφικού equalizer 1/3 της οκτάβας, 2x31 περιοχών constant Q. Επιλεγόμενο εύρος αυξομείωσης 6/12dB, φίλτρο αποκοπής χαμηλών συχνοτήτων στα 40Hz με 12dB ανά οκτάβα. Iσορροπημένες (balanced) είσοδοι και έξοδοι με XLR & TRS jacks, δυναμική περιοχή 108dB, 2U.
INPUT Connectors: 1/4" TRS, female XLR (pin 2 hot) Type: Electronically balanced/unbalanced, RF filtered Impedance: Balanced 40k ohm, unbalanced 20k ohm Max Input Level: >+21dBu balanced or unbalanced CMRR: >40dB, typically >55dB at 1kHz OUTPUTS Connectors: 1/4" TRS, male XLR (pin 2 hot) Type: Impedance-balanaced/unbalanced, RF filtered Impedance: Balanced 100 ohm, unbalanced 50 ohm Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater >+18dBm balanced/unbalanced (into 600 ohm) SYSTEM PERFORMANCE Bandwidth: 20Hz to 20kHz, +0.5/-1dB Frequency Response: 50kHz, +0.5/-3dB Dynamic Range: Typicall >112dB Signal-to-Noise: Typically >95dB THD+Noise: | Η ΤΙΜΗ ΔΕΝ ΠΕΡΙΛΑΜΒΑΝΕΙ Φ.Π.Α.
BSS Opal FCS-966 Constant Q Graphic Eq
Graphic equalisers are found in just about every sound application, from room contouring to feedback control and general audio sweetening.
Traditionally, much general eq'ing takes place on the faders alone, but this restricts the use of the faders at each end of the scale for further precision eq work. So we provided the Opal FCS-966 with separate LF and HF contour filters which can change an overall sound balance without disturbing a detailed room or loudspeaker response.
These filters are very musical gentle boost and cut shelving filters which can be used to add (or remove) room effects that change with temperature, audience numbers or humidity.
All these effects can be easily made without disturbing the critical fader settings already made.
Constant Q Filters
The modern generation of graphic eq's
uses the Constant Q topology, pioneered by BSS Audio, which means that the filter width is constant whatever the fader gain setting.
Compared to the earlier 'gyrator' style of filters, Constant Q filters provide a smoother and more predictable interaction between adjacent faders and the resulting eq curve more closely resembles the actual fader positions.
More Gain Control Per Filter
Each eq fader has +/-15dB of adjustable gain, more than many competitive graphic eq's. The faders are long-throw 45mm types for precision control.
High Pass Filter
Also provided on the FCS-966 is a sweepable high-pass filter which can be used very effectively to restrict the low-energy output for better amplifier and loudspeaker performance. Stage monitors also benefit from the application of a high-pass filter to remove bass signals e.g. from vocal-only wedges.
Metering
BSS Audio believes in providing engineers with information, and the FCS-966's 8-segment led meter shows output level and warns of signal clipping within the eq. When the unit is switched to bypass, the meter will read the input level, allowing accurate matching of the 'dry' and equalised signals using the gain control.
Centre Bypass
When any eq fader is in its centre detent position, the filter is automatically bypassed, for optimum performance.
Input/Outputs
All the inputs and outputs of the FCS-966 are electronically balanced, with optional transformer balancing. To make installation of the FCS-966 easier, we've provided three differerent interface connectors: XLR-type, 1/4" TRS jack and Phoenix/Combicon screw terminals.
Relay Bypass
The EQ IN buttons switch the EQ path
into circuit. When switched out, or power fails, a high-quality relay switches the input signal directly to the output connectors.
Control Descriptions
Faders
30 EQ filter faders on ISO centres, each with nominal +/-15dB of gain. Positive centre-detent on 45mm long-throw precision faders.
HP Filter
Sweepable high pass filter, frequency adjustable from OUT (flat) up to 250Hz.
LF Contour
Smooth shelving filter, +/-6dB of gain at 50Hz
HF Contour
Smooth shelving filter, +/-6dB of gain at 14kHz.
GAIN
Used for overall unity gain adjustment. Adjustable from - infinity to +10dB.
CLIP
Triple-point clip detector that indicates red when the internal signal is clipping at any one of three critical points.
LED Meter
Shows output signal level (input signal when eq is bypassed) from -24dBu to +18dBu in 8 steps. | Digital stereo active crossover with 4 inputs and 8 outputs, incl. software .
- Flexible routing configurations for all standard mono and stereo output operating modes
- 4 analog inputs and 8 analog outputs (XLR)
- Active frequency filter types (Bessel, Butterworth and Linkwitz-Riley) with slopes up to 24 dB/octave split up the audio signal into different frequency bands
- Incl. software editor (for PC and Mac) for remote control via computer through USB interface: store, transfer, and manage your presets
- Up to 30 user presets storable in the device via software
- 5 menu languages selectable (German, English, French, Spanish, Dutch)
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
- Mute switch with LED indicator per output
- 7-band parametric EQ per output
- Up to 7 ms signal delay adjustable for the outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase
- Lock function for prevents undesired changes to settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 10 and Mac OS X 10.5.8 and better
- Digital signal processor
- The device can be connected via USB to the PC in connection with DXO Software
The firmware can be updated via the PC connection
- (19") 48.3 cm rack installation 1 U
Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Power connection: |
Mains input via Coaxial power connector (M) power supply cord with AC adapter (provided) |
Frequency range: |
10 - 22000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Digital signal processor |
Crossover frequency: |
20-20000 Hz |
Impedance: |
Input 10 kOhm
Output 50 Ohm |
Gain: |
Output: -50 dB to +12 dB |
Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Delay: |
0 - 7 ms |
Dynamic range: |
Input: 114 dB
Output: 110 dB |
Sample rate: |
48 kHz |
Connections: |
Input: line via 4 x 3-pin XLR
Output: line via 8 x 3-pin XLR |
Max. level: |
Input: +22 dBu
Output: +9 dBu |
USB port: |
Typ B |
PC connect: |
DXO Software via USB, firmware can be updated |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimensions: |
Width: 48,3 cm
Depth: 22,3 cm
Height: 4,45 cm |
Weight: |
1,90 kg |
|
- Audiophile 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated Limiters with gain reduction meters for each channel protect your sound system from overload and distortion
- Pink noise generator provides test signals to adapt your sound system to any room acoustics
- Mono subwoofer output with dedicated level control and adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies e.g. floor rumble, hiss etc.
- Highly accurate 8-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
|
Μονοκάναλο equalizer εμπνευσμένο από το κλασικό Neve 1073, με ζεστό και μουσικό ήχο σε πολύ προσιτή τιμή.
Το EQ-73 αποτελεί ουσιαστικά το eq section του Neve 1073 χωρίς το φίλτρο high-pass, ενώ έχουν προστεθεί περισσότερες συχνότητες οι οποίες λειτουργούν με ρυθμίσεις stepped στα πρότυπα της vintage μονάδας για καλύτερη δυνατότητα ανάκλησης των ρυθμίσεων. Συνολικά, το εύρος των ρυθμίσεων είναι από 20Hz εως 24kHz με κέρδος +/-15dB για τις δύο χαμηλότερες μπάντες και +/-18dB για την υψηλή μπάντα.
Συνδυάζοντας το Pre-73, το EQ-73 και ένα Unite Rack, έχετε την αυθεντική μονάδα Neve σε ασυναγώνιστη τιμή!
Χαρακτηριστικά:
- Vintage Style electronics
- Ρύθμιση stepped για την επιλογή συχνοτήτων
- Μεγάλο εύρος επιλογής από 20Hz ως 24kHz
- Εύρος ελέγχου -/+18dB
- Χωριστοί διακόπτες bypass για κάθε μπάντα
- Σχεδιασμένο για να χρησιμοποιείται με το insert jack του Pre-73
- TRS in/out jack, 18dBu nominal level
- Εξωτερική τροφοδοσία
- Κλασικός ήχος, ιδανικός για κάθε μουσικό στυλ
- Συμπαγής, ανθεκτική κατασκευή
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.