Content |
The Soundweb London BLU-80 offers configurable I/O, configurable signal processing and CobraNet audio.
The BLU-80 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.
This processor features CobraNet audio with primary and secondary ports for fault tolerance. Control is through a separate Ethernet port which allows CobraNet and control networks to be easily separated or mixed depending upon requirements.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-80 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-80 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.
KEY FEATURES:
- Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Configurable Signal Processing
- Rich Palette of Processing and Logic Objects
- CobraNet Audio
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from
- HiQnet London Architect
|
Μέσω του NLB 60E επιτυγχάνουμε την εποπτεία καθώς και τη λειτουργία των ενισχυτών C Series.
Παρέχεται η δυνατότητα σύνδεσης μέχρι και 60 ενισχυτές C Series
Με τη βοήθεια του υπολογιστή και του αντίστοιχου προγράμματος που παρέχεται από τη LAB GRUPPEN, αυτόματα αναγνωρίζεται το δίκτυο των ενισχυτών C Series και μπορούν να ελεγχθούν, όπως επίσης να πάρουμε πληροφορίες για τη λειτουργία των ενισχυτών.
2XRJ45 IN AND OUT Ethernet Connectors
Auto Sensing 100V-240V AC
2x Contact Closure GPI
1x Voltage Sense GPI
Διαστάσεις: Π: 48.3cm (19”), Y: 4.4cm (1U), B: 20,8cm (8,2”)
Βάρος: 2,25 kg
|
The Soundweb London BLU-160 offers configurable I/O, configurable signal processing and a high bandwidth, fault tolerant digital audio bus.
The BLU-160 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.
This processor features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the distance between devices to over 40km.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-160 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-160 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.
Features - Four Input / Output Card Slots
- Configurable Inputs / Outputs
- Analog Inputs (with Phantom Power per Channel)
- Analog Outputs
- Digital Inputs (AES/EBU and S/PDIF)
- Digital Outputs (AES/EBU and S/PDIF)
- Configurable Signal Processing
- Rich Palette of Processing and Logic Objects
- 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
- Clear Front Panel LED Indication
- Informative Front Panel Display
- Bi-Directional Locate Functionality
- 12 Control Inputs and 6 Logic Outputs for GPIO Integration
- Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
- HiQnet Device
- Configuration, Control and Monitoring from HiQnet London Architect
|
The ARX EC-2 is a flexible yet affordable 24 dB per octave Phase Correct active crossovers. It has 2 modes of operation; as either Stereo 2 way or a Mono 3 way units, with a switch on the back panel selecting either mode.
Features Ultra low noise circuitry Totally phase aligned at crossover point Switchable Dual Channel 2 way or Single Channel 3 way Unique 'semi-fixed' crossover point 24dB per octave (Fourth Order) Linkwitz-Riley filters Separate Summed Mono Output Balanced Inputs and Outputs Built in High Pass filters Intuitive, 'user friendly' layout Flawless performance in any audio environment
Tamper-Proof Crossover Points The crossover points are determined internally by the value of 4 resistors per channel; changing the resistor value changes the crossover point. This 'semi fixed' method avoids the pitfalls of externally adjusted crossover points, making the crossover points tamper-proof once they are set. Idle fingers can't fiddle with the crossover points and create havoc with the system! As a handy guide, a list of common crossover points and their corresponding resistor values are printed inside the unit's lid, and also set out in the Owner's Manual. On the front panel are level controls for Low and High in dual channel 2 way mode, and Low, Mid and High in single channel 3 way mode, with corresponding Outputs on the rear panel.
Balanced Inputs and Outputs EC-2 has Balanced Inputs and Outputs, on XLR connectors. The EC-2 also has an additional summed Mono Low output, for applications that need a Mono Low feed (e.g. Left and Right full-range plus a single Sub Bass speaker). High Pass Filter There is also a preset 30 Hz HighPass filter to remove unwanted subsonics which can damage speakers and waste amplifier power. In addition, each output has up to +6 dB of gain available, to compensate for amplifiers and speakers of differing sensitivities. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240VAC, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage change switch. Uncompromising Audio Quality Innovative circuit design is pointless unless it delivers stunning sound quality, and here the EC-2 excels. It has been designed for uncompromising audio quality, and to achieve this, Linkwitz Riley 24dB (Fourth Order) state variable filters are used throughout, ensuring a smooth Phase Correct transition through the crossover region. From Stage Monitors to Studio Monitors, from Front of House to the Front room of your House, the ARX EC-2 is a crossover that is suited to any application that requires flawless, transparent sound. You'll never compromise on Quality when you choose ARX
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 21 dB CMRR >45 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 21dB Frequency Response 30Hz-20KHz +or- 0.5dB Note: 30 Hz is a function of the High Pass filter Signal to Noise ratio (Controls at Unity) -90 dB Unweighted, -93 dB 'A' weighted Distortion 004% THD,0dB,1KHz Dynamic Range 111 dB Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 13/4“H x 6“D, 482 x 44 x 155mm Input Connector type XLR Output Connector type XLR Crossover point frequencies are changed internally by varying the value of 4 resistors per channel.
Front Panel Controls Low and High Output controls for 2 way mode Low, Mid and High Output controls for 3 way mode Marker panels for labelling crossover assigns 2 way/ 3 way status LEDs Rear Panel Balanced XLR Inputs and Outputs Additional summed mono Low output 2 way / 3 way mode switch |
Advanced Feedback Suppression® Processor with Full LCD Display
Hear No Evil and See no Evil.
The AFS2 Advanced Feedback Suppression processor has been completely re-designed to take the foundation of the best selling AFS224 and bring it to thte next level. The AFS2 now offers the highly-intuitive Wizard function that takes all of the guesswork out of setting up any room. The AFS2 also incorporates a completely re-designed Advanced Feeback Supression module. Best of all, the AFS2 now provides the user with a full LCD display setup and monitoring.
With its powerful DSP module, the AFS2 provides all the processing and control necessary for both installation and live use. Ten and twelve filter feedback elimination processors are the de facto standard, but the AFS2 offers a dedicated feedback suppression processor that offers up to 24 filters per channel with filter Qs up to 1/80 of an octave. To achieve these staggering numbers dbx utilized their improved AFS technology that had previously only been available in the upper echelon line of products and made it available in this stand-alone processor. In addition to the plethora of feedback suppression filters available, the AFS2 also offers selectable modes, live filter lift, and types of filtration, which are all readily available via the intuitive user interface front panel. With all of these state-of-the-art features in place, not only do you hear no evil, but you will now be able to see no evil. ®
Features
- Wizard Setup Function
- Full LCD Display
- dbxʼs patented (Advanced Feedback Suppression) AFS™ technology
- 24 Programmable Filters per Channel
- Stereo or Dual Independent Channel Processing
- Live and Fixed Filter Modes
- Selectable Filter Lift Times
- Application-specific filter types include: Speech and Music Low, Med and High
- Input channel Metering
- 24 LED per Channel Filter Metering
- XLR and TRS Inputs and Outputs
Specifications
Number of Inputs
|
2
|
Input Connectors
|
Female XLR and 1/4” TRS
|
Input Type
|
Electronically balanced/unbalanced, RF filtered
|
Input Impedance
|
Balanced 50kΩ, Unbalanced 25kΩ
|
Max input line level
|
+20 dBu
|
CMRR
|
> 40dB, typically >55dB @ 1kHz
|
Number of Outputs
|
2
|
Output Connectors
|
Male XLR and 1/4” TRS
|
Output Type
|
Electronically balanced/unbalanced, RF filtered
|
Output Impedance
|
Balanced >120 Ω, Unbalanced >60 Ω
|
Max Output Level
|
+20 dBu
|
A/D Converter
|
dbx Type IV™ Conversion System
|
A/D Dynamic Range
|
>113 dB A-weighted, >110 dB unweighted, 22kHz BW
|
Type IV Dynamic Range
|
>119 dB, A-weighted, 22kHz BW; >117 dB, unweighted, 22kHz BW
|
A/D Conversion
|
24-bit
|
Sample Rate
|
48kHz
|
D/A Dynamic Range
|
112 dB A-weighted, 109 dB unweighted
|
D/A Conversion
|
24-bit
|
Dynamic Range
|
109 dB A-weighted, 106 dB unweighted, 22kHz BW
|
THD+Noise
|
0.003% typical at +4 dBu, 1 kHz
|
Frequency Response
|
20Hz – 20kHz, +/- 0.5dB
|
Interchannel Crosstalk
|
>80 dB typical
|
Crosstalk input to output
|
>80 dB
|
Operating Voltage
|
100-120VAC 50/60 Hz - EU: 220-240 VAC 50/60 Hz
|
Power Consumption
|
9 W
|
Unit Weight
|
4.5 lbs. (2.04 kg)
|
Dimensions
|
1.75” (H) x 5.75” (D) x 19” (W), 4.4cm (H) x 14.6cm (D) x 48.26cm (W)
|
|
Τροφοδοσία ρεύματος: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Σύνδεση ρεύματος: |
Είσοδος δικτύου μέσω ομοαξονικού βύσματος τροφοδοσίας (M) καλώδιο τροφοδοσίας με μετασχηματιστή εναλλασσόμενου ρεύματος (παρέχεται) |
Εύρος συχνοτήτων: |
10 - 30000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Ψηφιακός επεξεργαστής σήματος |
Αντίσταση: |
Είσοδος: 10 kOhm
Έξοδος: 50 Ohm |
Gain: |
Έξοδος: -50 dB to +12 dB |
Φίλτρο: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Καθυστέρηση: |
0 - 5 ms |
Δυναμικό εύρος: |
Είσοδος: 114 dB
Έξοδος: 110 dB |
Sample rate: |
67 kHz |
Συνδέσεις: |
Είσοδος: line μέσω 2 x 3-pin XLR
Έξοδος: line μέσω 6 x 3-pin XLR |
Συχνότητα Crossover: |
20-20000 Hz |
Max. level: |
Είσοδος: +22 dBu
Έξοδος: +9 dBu |
USB θύρα: |
Τύπος B |
Σύνδεση PC: |
DXO Λογισμικό μέσω USB, το λογισμικό μπορεί να ενημερωθεί |
Σχεδιασμός περιβλήματος: |
(19") 48.3 cm εγκατάσταση ραφιού 1 U |
Διαστάσεις: |
Πλάτος: 48,3 cm
Βάθος: 12,8 cm
Ύψος: 4,45 cm |
Βάρος: |
1,77 kg |
Λειτουργικό σύστημα: |
Win XP, Win Vista, Win 7, Win 10, OS X 10,5 ή καλύτερα |
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.