Content |
DPR-504 Νoise gate τεσσάρων καναλιών |
DBX-1046
Compressor - limiter 4 εισόδων, κύκλωμα "overeasy“, peakstoplus,
είσοδοι - έξοδοι XLR και 1/4 TRS. Κατάλληλος για studio, live χρήση.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | Max Input | > +22 dBu balanced or unbalanced | CMRR | Typically >50 dB at 1 kHz | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Output Type | Servo-balanced/unbalanced, RF filtered | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | Noise | | Dynamic Range | > 118 dB, unweighted | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | IMD | | Interchannel Crosstalk | | Stereo Coupling | True RMS Power Summing | Compressor Threshold Range | -40 dBu to +20 dBu | Compressor Ratio | 1:1 to infinity:1 | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | Compressor Attack/Release Characteristic | AutoDynamic™ | Compressor Attack Time | Program-dependent | Compressor Release Time | Program-dependent | Compressor Output Gain | -20 to +20 dB | Limiter Threshold Range | 0 dBu to +24 dBu (off) | Limiter Ratio | infinity:1 | Limiter Type | PeakStopPlus® two-stage limiter | Limiter Stage 1 | PeakStop® brickwall limiter | Limiter Stage 1 Attack Time | Zero | Limiter Stage 1 Release Time | Zero | Limiter Stage 2 | Predictive intelligent program limiter | Limiter Stage 2 Attack Time | Program-dependent | Limiter Stage 2 Release Time | Program-dependent | OverEasy® Switch | Activates the OverEasy compression function | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | Bypass Switch | Activates the direct input-to-output hard-wire bypass | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | Function Switches | LED indicator for each front-panel switch | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | Power Consumption | 20 Watts | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | Power Connector | IEC receptacle | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | Unit Weight | 5.2 lbs. (2.4 kg) | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
High-Definition 31-Band Stereo Graphic Equalizer with FBQ Feedback Detection System
- Professional 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies, e.g. floor rumble, hiss etc.
- Highly accurate 12-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard-bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving - 3-Year Warranty Program*
- Conceived and designed by BEHRINGER Germany
|
Innovation
The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter designed for use in any professional audio dynamics control application. Multiple Modes The Afterburner can be set up and used in three different ways: In Two channel mode, it performs as two independent compressor/limiters, with 'industry standard' variable Threshold, Ratio and Output gain. In stereo mode, our New Adaptive Stereo Link circuitry provides increased stereo imaging accuracy when linking both channels as a stereo pair. A single front panel switch puts the Afterburner into its alternative Mono mode, setting it up as a Single channel, Dual Band compressor/limiter, with separate dynamics control of both Low and High frequencies, opening up a whole new range of gain control techniques. Enhance Switch In any mode, the Afterburner features an 'Enhance' switch, which provides frequency restoration to preserve the spectral balance of the audio signal, compensating for the sagging Low and High frequency response of compressed program material. Think of it as a 'smart' loudness control. Features Switchable Modes - Stereo; Dual Channel Single band; or Single Channel Dual Band (Low and High) Low and High frequency compression in Single Channel mode 'Enhance' switch restores spectral balance of compressed signal New Hard/Soft knee compression switch New Adaptive Stereo Link circuit for accurate stereo imaging New Above/Below Threshold LEDs enable at-a-glance compression confirmation Balanced XLR and Jack Inputs and Outputs Sidechain Insert points Intuitive user-friendly layout Flawless performance New Above/Below Threshold LEDs enable at-a-glance compression confirmation New Hard or Soft knee compression option New LED metering provides accurate Level status, with separate Gain Reduction metering in easy to read 'wide scale' meters. There is also comprehensive LED indication of all operating functions and status in any mode. Balanced Inputs and Outputs On the rear panel, each channel has true differential Balanced inputs and outputs, on both XLR and TRS jack connectors. As well, each channel has a TRS jack Sidechain access insert point, for applications such as De-essing (when used with an external equalizer such as the ARX Multi Q or EQ 260).Other features include a true Hardwire bypass switch for each channel, and passive RFI filters on the inputs. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and voltage change switch. With its smooth compression, intuitive user friendly layout, high density precision circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner is equally at home in Studio, Installation, Broadcast and Sound Reinforcement environments. It can provide great sounding dynamics control effects that are not available with any other device. T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 22 dB CMRR >60 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 22 dB Frequency Response 20Hz to 20KHz ±0.2dB Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted Distortion .02% THD @ 0dB,1KHz Dynamic Range 115 dB Sidechain Insert Impedance 10 Kohm Filter Section Filter Type Phase corrected 6dB/octave Summed Filter Response ±0.2dB through crossover region Dividing Frequency 250 Hz Enhance Section Low Enhance 50 Hz, High Enhance 10 KHz Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input/OutputConnector type XLR, Balanced Jack Sidechain Insert Connector TRS Jack
Front Panel Controls Hardwire bypass IN/OUT switch Threshold, Ratio and Output Gain controls Above/Below Threshold LEDs 12 segment LED Output Level display Numbered marker panel for labelling compressor assigns 7 segment LED Gain Reduction display Enhance switch and status LED Adaptive Stereo link switch and status LED Dual/Single channel mode switch and status LEDs Rear Panel Connectors Balanced Inputs and Outputs, on both XLR and TRS jack connectors. In Single channel (Mono) mode, use Channel 1 Inputs and Outputs only Sidechain Insert TRS connector on each channel AC input connector, with voltage switch and fuse. |
Σχόλια: Αναλογικό τηλεφωνικό υβρίδιο 2 τηλεφωνικών γραμμών, σχεδιασμένο για να ικανοποιεί τις απαιτήσεις των τηλεοπτικών και τα ραδιοφωνικών σταθμών. Βalanced είσοδοι και έξοδοι ήχου με υποδοχές XLR, έλεγχος στάθμης στο εμπρόσθιο τμήμα της συσκευής. Απομακρυσμένος έλεγχος αποδοχής-απόρριψης γραμμής, ενεργοποίησης-απενεργοποίησης τηλεφωνικής συνδιάσκεψης, ειδοποίησης εισερχόμενης κλήσης. Ενδεικτικό LED εμφάνισης των επιπέδων σήματος λήψης, αποστολής ή συνδιάσκεψης. Αυτόματη αντιστάθμιση ποιότητας γραμμής. Παρέχει δυνατότητα επέκτασης του συστήματος χρησιμοποιώντας επιπλέον συσκευές Μacrotel και επιτρέποντας τον έλεγχο δύο τηλεφωνικών γραμμών από μία είσοδο της κονσόλας.
GENERAL DATA
Power Supply 220 / 110V 25 VA
Dimension 434x351x44mm (1 rack unit)
Weight » 4 Kg
MEETING INTERFACE IN / OUT
Connector DB 9 female
Nominal in / out audio level 0 dBm
Input impedance 600 W / 10 KW (selectable)
Output impedance 100 W
* nominal line level: - 6 dBm
** it can vary depending on characteristics of telephone line
All measurements are intended at 1 kHz.
AUDIO PROGRAM IN / OUT
Connectors XLR, electr. balanced
Input impedance 600 W / 10K W (selectable)
Output level * - ¥ ¸ + 16 dBm
Output impedance 100 W
Noise on Receive output
2-Wire separation £ 25 dB**
4-Wire separation £ 70 dB
2-WIRE SECTION
Connector RJ11
Nominal input level - 6 dBm
Nominal output level - 6 dBm
Compensation mode Electronic, transf. decoupled
Impedance 600 W
4-WIRE SECTION
Connector Terminal block
Impedance 600 W
Nominal TX level 0 dBm
Nominal RX level 0 dBm
|
Features
Unique High Density design puts SIX gates in
minimum rack space
Intuitive, 'user friendly' layout
Balanced Inputs and Outputs
Fast, low noise opto-coupler circuitry
Sidechain/Key Input points on each channel
Hardwire Bypass switch on each gate
Flawless performance in any audio environment
The sheer amount of effects and signal processors required for today's
standards of audio production puts a great strain on the available space
in equipment racks, both in the studio and on the road.
So, in order to give engineers more control in less space, we've created
the ARX Sixgate; Six full function noise gates neatly housed in a compact,
all steel 1 RU package, without sacrificing features or quality.
Why Six gates?
Research shows that the majority of noise gates get used on drum kits,
which means using typically 5 to 6 gate channels. Compare this to the
two or maybe 4 channels that most other units have, and you'll see the
reason for the Sixgate's success.And, by using a minimalist approach to
drum gates, the ARX Sixgate has enough gates left over for backing vocals
and other instruments.
Industry Standard controls
Front panel controls for each gate consist of the 'Industry Standard' controls
for Release, Depth and Threshold, plus Red and Green LED displays to indicate
Gate Open or Closed status, and an IN/OUT hardwire bypass switch.
In addition to this, each gate has a blank panel to write on for easy confirmation
of gate assigns. No more pieces of masking tape stuck everywhere!
Ultra Low Noise
Internally, each gate has proprietary ARX ultra low noise high-speed opto-coupler
circuitry with program dependent Attack time, which tracks the incoming signal to
automatically determine optimum gate response.
Balanced Inputs and Outputs
The rear panel features true differential Balanced Inputs and Outputs for each gate,
on insulated TRS jack connectors.Each gate channel also has Individual Key Inputs/
Sidechain access insert points which can be used either for gate control by an external
signal, or for frequency sensitive gating (when used in conjuction with an external
equalizer such as the ARX EQ260).
Universal AC Power
AC power range on the Sixgate is a universal 100 to 120V or 220 to 240V, and is
connected to the unit via a standard 3 pin IEC connector, with built-in fuse and voltage
switch.
The Sixgate's unique combination of High Density design, intuitive 'user friendly' controls,
and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance
Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise Ratio
Gate Closed: -95 dB Unweighted, -105 dB 'A' weighted
Gate Open, Depth Minimum: -93.5 dB Unweighted -98dB
'A' weighted
Distortion 0 .01% THD @ 0dB,1KHz
Dynamic Range 125 dB
Attack Time Program dependent using high-speed
opto-couplers
Release Time User variable
Input and Output Connector type Balanced Jack
Sidechain Insert Connector TipRingSleeve Jack
Sidechain Insert Impedance 10 Kohm
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“Wide x 13/4“High x 6“Deep; 482 x 44 x 155mm
Front Panel Controls
Individual Release, Depth and Threshold controls
Hardwire bypass IN/OUT switch
Open/Closed gate status LED
Marker panel for labelling gate assigns
Rear Panel
Balanced Inputs and Outputs, on Balanced jack
connectors
Sidechain Insert/Key Input TipRingSleeve jack on
each channel
AC input connector, with voltage switch and fuse
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.