CROWN XLi-2500 Tελικός ενισχυτής 2x750W/4Ω-500W/8Ω-1Χ1500W bridge 8Ω 2U Rack

Τελικός ενισχυτής 2x750W/4Ω-500W/8Ω-1Χ1500W bridge 8Ω. Stereo/Parallel/Bridge mode. 0.775-1.4v ευαισθησία. Είσοδοι XLR/RCA- Έξοδοι Speakon+Binding post. Ρυθμιστικά Level-gain-operation mode. Eνδεικτικά LED. Προστασία για Βραχυκύκλωμα-κενό φορτίο-καθυστέρηση έναρξης-αντιπαρασιτικό RF. 2RU Διαστασεις ΥΠΒ 8.9Χ 48.1 Χ 38.6cm. Bάρος 13.7 κιλά.

• Reasonably priced, robust and powerful power amplifier
• Robust and analog circuit
• LED display for each channel for signal, clip and error
• Stereo, bridge and parallel modes
• Conventional power supply
• Performance: 2 x 520 Watt an 8 Ohm, 2 x 800 Watt an 4 Ohm
• Inputs: Cinch, XLR
• Outputs: 2 x speakon, spring clip
• Robust 19 inch housing
• Height: 2 U

Τελικός ενισχυτής 2U ισχύος 2 Χ 750 Watt/4Ω με απόκριση συχνότητας 20Hz - 20KHz. Βάρος 19 Kg. Διαθέτει ρύθμιση ευαισθησίας εισόδου (0,775V/1,0V/1,44V), Limiter και φίλτρα Low pass & High pass για σύνδεση με sub ή δορυφόρο. Διαθέτει εισόδους balanced XLR/JACK και εξόδους ηχείων σε Speakon & Binding post

Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps.

The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.

In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.

• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.

Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)


DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.


Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)

Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs

Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™

XR Series - Intelligent Power
New Horizons.

A lightweight with enormous power output. Combined with digital signal processing.
That's what we call flexibility! Locally controlled or completely networked.
No matter what the requirements are.
The integrated powerful digital signal processor (DSP) and controller allows
for a troublefree and easy adjustment to any acoustical environment.
Wear-free digital potentiometers, sequential remote power on,
alive contacts for easy supervision, computer controlled monitoring -
 its enless list of useful feature make it the right choice for any installation.
XR - the new definition of Intelligent Power

High Tech SMT Design
Digital Signal Processor
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX / Speakon
High-End Switched Power Supply with Power Factor Correction (not XR4000)
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed low noise fans
Digital wear-free Volume Controls (can be operated manually)
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Paging Input
Monitor Output
SXL Dataport
Perfect Weight-to-Power ratio
3 Years Warranty

Technical Data:
 
Class:  H
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.02%
Signal-to-Noise Ratio:  < -106 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  750 to 1200 @ 4 Ohm
Cooling:  4 Fans (temp. reg. variable speed)
Weight:  8 to 10 kg (18 to 22 lbs)
Dimensions:  2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)