Content | The introduction of the Drawmer DL241 Dual Channel \'Auto-Compressor\' highlights the beginning of a new generation of dynamic processors which set new standards of sonic excellence. Its combination of features, displays and well designed control functions make it an outstanding product for a vast range of broadcast, sound reinforcement, and recording applications. The DL241 \'Auto-Compressor\' incorporates many automatic functions allowing the engineer to achieve optimum results in the minimum set up time but does not compromise skilled users with limited controls. Its sophisticated design produces a smooth, transparent and warm sonic performance.
Facilities available on the DL241 include:
Expander/Gate : Drawmer\'s unique "Programmed Adaptive Expansion" circuitry allows effective \'single control operation\' producing a fast smooth response and eliminating \'chatter\' on or around threshold. This design differs from that of conventional Expanders in that the Expansion Ratio, Hold Attack and Release continually adapt themselves to the dynamics of the incoming signal. The Expander/Gate provides 80dB range and variable threshold from +20dB to 70dB with an OFF position. Switching is provided for \'Fast\' or \'Slow\' release characteristics. The \'Fast\' mode can be used for instruments with rapid decay times or for additional tightening of the gating effect. The \'Slow\' mode is more suitable for vocals and instruments with longer decay times or can be used to smooth over rough fade outs. A single LED indicates gating action.
Compressor : A full Auto Attack/Release Compressor with variable Threshold and Ratio successfully combines the smoothness of the \'Soft Knee\' principle with the precision of a \'Ratio\' control. The advantage of this combination is that instead of the onset of compression being sudden at the threshold point the ratio increases over a 10dB input level range until it reaches the ratio set on the front panel control, thus achieving a more natural sounding compression. Selectable manual or fully automatic Attack and Release times dramatically extend the application range and user scope of the DL241. Selecting the \'Auto\' mode removes the need for manual adjustment and is particularly valuable when the program being treated does not have predictable or consistent dynamics, often the case when processing a complete mix or a virtuoso bass guitar performance. Under manual control the wide range of adjustment available gives the user the ability to create dynamic effects as well as normal compression.
Peak Level. \'Zero Response Time\', \'Zero Overshoot\' circuitry : This provides an absolute limit to the peak level of the output signal, adjustable from OdB to +16dB above system level. When set to the required level, any excessive peaks will be stopped and the gain momentarily decreased if necessary. The \'Zero Response Time\' is essential to avoid unpleasant distortion when mastering for CD or sending any signal to digital equipment. \'Zero Response Time\' means that the DL241 provides complete protection from even the fastest and shortest signal \'spikes\' (overloads), making the unit also ideally suited for speaker system protection in sound reinforcement applications.
Metering : Comprehensive bar graph displays give \'at a glance\' indications of gain reduction, and output signal level Gain reduction from 1dB to -30dB is shown simultaneously with signal level from -20dB to +15dB Other single LEDs indicate function status of Gating Acton, Auto Mode, Bypass, Peak Limiting, Stereo Linking, and Power On.
Stereo Link : When processing stereo signals, linking should be used to prevent image shifting. This facility ties both channels together. Using channel 1 (left) as the master channel removes the need to duplicate control settings for both channels.
Bypass : A fully balanced hard-wire bypass connects the input directly to the output allowing signal to pass through the unit with no power applied. In bypass the VU level meter displays the Input signal.
Operating Level : The operating level of the DL241 can be instantly switched, independently on each channel, for either +4dBu or -10dBu operation using a rear panel push switch.
Input/Output : The DL241 is available with either XLR connections and fully balanced inputs and outputs, or with stereo jack (TRS) connections, fully balanced inputs and single ended outputs. |
VIRTUALIZER 3D FX2000 - Υψηλής απόδοσης 3D Multi-Engine Επεξεργαστής εφέ.
• 71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
• Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
• Awesome modulation, dynamic, psychoacoustic and EQ algorithms
• Authentic amp simulation, distortion and special effects
• 11 effect combinations with selectable serial / parallel configuration
• Up to 7 adjustable parameters plus 2-band EQ per effect
• 24-bit A/D and D/A converters with 64/128-times oversampling
• True stereo processing for realistic channel separation in stereo image
• 100 factory presets plus 100 user memory locations
• Extensive MIDI implementation
• Accurate LED level meters for perfect level setting and optimum performance
• Servo-balanced XLR and ¼'' TRS inputs and outputs
The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.
The FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.
• Reverbs: Cathedral - Gold plate - Small hall - Studio - Concert - Stage - Spring & Reverse Reverb - Ambience and more...
• Delays: Stereo - Tape Echo - Ping Pong and more...
• Modulation and Pitch Shifter FX: Stereo/Vintage/Jet Stream Flanger - Stereo/Analog/Vintage/Ultra/ Chorus - Stereo/Vintage/Dual Phaser - Rotary - Pitch Shifter - Vibrato and more...
• Dynamic FX: Compressor – Expander – Gated Reverb – An. Compr/Lim. — Ultramizer – Denoiser – De-Esser and more...
• Psychoacoustic FX: Exciter – Enhancer – Stereo Imager and more...
• Filter/EQ FX: Auto/LFO Filter – Parametric/Graphic EQ.
• The FX2000 is also equipped with distortion, amplifier and speaker simulation including Vocal/Tube distortion, Guitar Amp and more...
• Special FX:Vinylizer - Sampler - Vocoder - Voice Canceler - Resonator.
|
DPR-504 Νoise gate τεσσάρων καναλιών |
DBX-1074
4 ch noise gate με δυνατότητα λειτουργίας σε ρυθμιζόμενο εύρος
συχνοτήτων XLR in/out, insert points.
- Four independent channels of gating
- Independent key filtering
- Independent Threshold and Release controls
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Stereo Coupling mode
- Switchable +4dBu or -10dBv operation per channel
Input Connectors | XLR (Pin 2 and tip hot) | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm | Max Input | > +22 dBu balanced or unbalanced | CMRR | 40dB: Typically >55 dB at 1 kHz | Key Input | Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm | Output Connectors | XLR (Pin 2 hot) | Output Type | Servo-balanced/unbalanced, RF filtered | Output Impedance | Balanced 60 Ohm, unbalanced 30 Ohm | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | Frequency Response | 0.35 Hz to 200 kHz, +0/-3 dB | Noise | | Dynamic Range | > 115 dB, unweighted | THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | Interchannel Crosstalk | | Stereo Coupling | True RMS Power Summing | Operating Voltage | 100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | Power Consumption | 30 Watts | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | Power Connector | IEC receptacle | Unit Weight | 6.9 lbs. | Shipping Weight | 9.3 lbs. |
|
Features Four Independent Compressor Channels Channels 1 and 2, 3 and 4 are stereo linkable 7 LED Gain Reduction metering Balanced XLR Inputs and Outputs Sidechain Insert points Intuitive, user friendly layout Flawless performance The sheer amount of effects and signal processors necessary for today's standards of audio production puts a great strain on the available space in equipment racks, both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp. An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our original design concept. The Quadcomp is still four variable ratio Compressor/ Limiters neatly housed in a compact all steel 1 RU package. However, all new low noise/low distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp in a class of its own. More Control, Less Space On the front panel, each channel has the 'industry standard' individual controls for Threshold, Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual indication of the amount of gain reduction being applied to the program, and an IN/OUT hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write on for easy confirmation of compressor assigns. Precision Circuitry Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters for low distortion and accuracy, plus program dependent attack and release time, which automatically determines optimum compressor response. Balanced Inputs and Outputs The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor. Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260). Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate stereo tracking. When switched IN, the first channel becomes the master and controls all the functions of the second except Output gain. Universal AC Power AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via a standard IEC connector, with built-in fuse and voltage switch. Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs, Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry and clean uncluttered layout make it a truly useful audio tool for all applications.
T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 20dB CMRR >50dB, 20 Hz?20 KHz Output Impedance Balanced 300 ohms Unbalanced 150 ohms Output Level (Max) + 20 dB Frequency Response 20Hz-20KHz ±0.5dB Signal to Noise ratio -93 dB Unweighted, -98 dB ?A? weighted Distortion .015% THD @ 0dB,1KHz Dynamic Range 108 dB Attack and Release Times Program dependent Metering 7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB Sidechain Insert Impedance 10 Kohm Power Requirements 100/120 V AC or 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input Connector type Balanced XLR Output Connector type Balanced XLR Sidechain Insert Connector TRS Jack
Front Panel Controls Hardwire bypass IN/OUT switch Threshold, Ratio and Output Gain controls 7 LED Gain Reduction display Marker panel for labelling compressor assigns Stereo link status LEDs Rear Panel Connectors Input and Output balanced XLR connectors TipRingSleeve Sidechain insert connectors Channels 1 and 2, 3 and 4 Stereo link switches IEC AC mains connector with inbuilt fuse and voltage change |
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor. Ανιχνεύει αυτόματα τους μικροφωνισμούς και τους εξαφανίζει. Διαθέτει επίσης low cut filter, phantom power, balanced in/out.
Χαρακτηριστικά:
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor
Αυτόματα ανιχνεύει και εξολοθρεύει 8 συχνότητες μικροφωνισμών
Ultra low noise mic/line είσοδος με gain control και +48V phantom power τροφοδοσία για πυκνωτικό μικρόφωνο
Delay line μέχρι 2,5 sec και με ρύθμιση μέτρων ποδιών και msec
Noise gate με αυτόματες και manual ρυθμίσεις
Αυτόματο compressor
Low cut filter με ρύθμιση συχνότητας
Είσοδος – έξοδος σε balanced JACK 6,35 και XLR
Frequency response: 10H – 21KHz
Noise: 92dB (line), 89dB mic
THD: 0.007%
Μετατροπείς: 24bit Sigma-Delta, 64/128-times oversampling
Η συσκευασία περιλαμβάνει: fbq100, users manual
Τροφοδοσία: AC 220V / 50Hz
Διαστάσεις: 56 x 88 x 132 mm
Βάρος: 380 gr
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.