DYNACORD SUB 112 – ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 12” 400W (ΜΑΥΡΟ)

Καταργήθηκε

664.36 με ΦΠΑ 24%

Εξαντλημένο

CompareAdd to wishlist Υποβολή Καλύτερης Τιμής
Διαθεσιμότητα: Καταργήθηκε Καταργήθηκε Κωδικός προϊόντος: SUB 112 Κατηγορία:
DYNACORD΄s SUB 112 is a vented, direct radiating cabinet, equipped with the high-power DYNACORD DND12S400 neodymium transducer. The conical vent system shows significantly less distortion and lower air noise at low frequencies than common circular vent openings. The SUB 112 contains a passive filter, 6 dB/oct., that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs […]

 

Διαβάστε περισσότερα

DYNACORD΄s SUB 112 is a vented, direct radiating cabinet, equipped with the high-power DYNACORD DND12S400 neodymium transducer. The conical vent system shows significantly less distortion and lower air noise at low frequencies than common circular vent openings.
The SUB 112 contains a passive filter, 6 dB/oct., that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs D 8 can therefore be directly connected in parallel to the SUB 112 if an extended bass reproduction is required. You just have to connect the SUB 112 and the D 8 with a regular Speakon cable in parallel.
The SUB 112 cabinet is made of 15mm birch plywood. All corner joints and braces are grooved and glued. The cabinet΄s surface is painted with a 2-K laquer finish . The acoustic foam front on a powder coated steel grille protects the DND12S400 woofer against damage during transport and bad environmental conditions. The connector panel uses two 4-pole Speakon connectors (INPUT/THRU) for a safe connection and easy daisy-chaining to other cabinets. The pin assignment is 1+/1-. Pins 2+ and 2- are also connected between the two Speakon connectors. A pole-mount flange allows easy speaker-on-a-stick applications. Please always take care that every speaker stack has been mechanically secured against accidental falling down. Please always consult a certified structural engineer for correct and safe setup methods.
The cabinet is equipped with four large rubber feet. Two handles allow easy and safe transport. A protective cover is available as an optional accessory.

Βάρος 22.00 kg

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Κάνετε την πρώτη αξιολόγηση για το προϊόν: “DYNACORD SUB 112 – ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 12” 400W (ΜΑΥΡΟ)”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

Quick Comparison

DYNACORD SUB 112 - ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 12'' 400W (ΜΑΥΡΟ) removeJBL VRX915M 15'' 2-way 800W RMS Stage Monitor removeRCF S4022 - ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 2x12" 800W (ΜΑΥΡΟ) removeRCF S4012 Bandpass Subwoofer 12" 400 W removeHK AUDIO PREMIUM PR:O 12M MONITOR 400W removeRELOOP ACTIVE PA Set Ενεργό Σετ PA remove
NameDYNACORD SUB 112 - ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 12'' 400W (ΜΑΥΡΟ) removeJBL VRX915M 15'' 2-way 800W RMS Stage Monitor removeRCF S4022 - ΠΑΘΗΤΙΚΟ ΗΧΕΙΟ SUBWOOFER 2x12" 800W (ΜΑΥΡΟ) removeRCF S4012 Bandpass Subwoofer 12" 400 W removeHK AUDIO PREMIUM PR:O 12M MONITOR 400W removeRELOOP ACTIVE PA Set Ενεργό Σετ PA remove
Image
SKUSUB 112VRX 915MS402213000048PRO 12MActive PA set
Rating
Price 664.36 με ΦΠΑ 24% 2,237.00 με ΦΠΑ 24% 1,162.50 με ΦΠΑ 24% 818.00 με ΦΠΑ 24% 527.00 με ΦΠΑ 24% 1,020.83 με ΦΠΑ 24%
Stock

Εξαντλημένο

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

Σε απόθεμα

Διαθέσιμο κατόπιν παραγγελίας

Μόνο 5 απομένουν σε απόθεμα

AvailabilityΕξαντλημένοΔιαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίαςΣε απόθεμαΔιαθέσιμο κατόπιν παραγγελίαςΜόνο 5 απομένουν σε απόθεμα
Add to cart

Διαβάστε περισσότερα

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Description
Content

DYNACORD΄s SUB 112 is a vented, direct radiating cabinet, equipped with the high-power DYNACORD DND12S400 neodymium transducer. The conical vent system shows significantly less distortion and lower air noise at low frequencies than common circular vent openings.
The SUB 112 contains a passive filter, 6 dB/oct., that suppresses high frequencies. Appropriate fullrange cabinets, e.g. DYNACORDʼs D 8 can therefore be directly connected in parallel to the SUB 112 if an extended bass reproduction is required. You just have to connect the SUB 112 and the D 8 with a regular Speakon cable in parallel.
The SUB 112 cabinet is made of 15mm birch plywood. All corner joints and braces are grooved and glued. The cabinet΄s surface is painted with a 2-K laquer finish . The acoustic foam front on a powder coated steel grille protects the DND12S400 woofer against damage during transport and bad environmental conditions. The connector panel uses two 4-pole Speakon connectors (INPUT/THRU) for a safe connection and easy daisy-chaining to other cabinets. The pin assignment is 1+/1-. Pins 2+ and 2- are also connected between the two Speakon connectors. A pole-mount flange allows easy speaker-on-a-stick applications. Please always take care that every speaker stack has been mechanically secured against accidental falling down. Please always consult a certified structural engineer for correct and safe setup methods.
The cabinet is equipped with four large rubber feet. Two handles allow easy and safe transport. A protective cover is available as an optional accessory.

JBL VRX915M 15'' 2-way 800W RMS Stage Monitor

Key Features :
 
Compact and low-profile for minimal obstruction of audience sightlines

50 x 90 nominal coverage

Bi-amplified or full-range passive operation

Differential Drive woofer with neodymium magnet for high power capacity and very light weight

4" (voice coil) diameter compression driver with neodymium magnet

Specifications:

Frequency Range

:

60 Hz - 20 kHz

Frequency Response

:

70 Hz - 20 kHz

Coverage Pattern

:

50 x 90 nominal

Crossover Modes

:

Passive / Bi-amp

  Crossover Frequency

:

1.1 kHz

Power Rating2 (Continuous / Program / Peak)

:

Passive Full-Range 800 W / 1600 W / 3200W, 2 hrs1 Passive Full-Range 600 W / 1200 W / 2400W, 100 hrs

System Maximum SPL

:

127 dB SPL continuous (133 dB SPL peak)

System Sensitivity (1w @ 1m

:

98 dB SPL

LF Driver

:

1 x JBL 2265H 380 mm (15 in) Differential Drive?? woofer 8 Ohms

HF Driver


1 x JBL 2452H, 100 mm (4.0 inch) diameter voice coil, 38 mm (1.5 inch) exit, neodymium magnet compression driver 8 Ohms


Nominal Impedance

:

8 ohms

Active Tunings

:

Tunings available at www.jblpro.com

Enclosure

:

Symmetrical stage monitor, 15/18 mm, plywood

Finish

:

Black DuraFlex finish

Grille

:

Powder coated, black, 16 gauge perforated steel with acoustically transparent black screen backing

Input Connectors

:

Neutrik Speakon NL-4 (x2), one on each end

Dimensions (H x W x D)

:

629 mm x 432 mm x 324 mm (375 mm stage height) 24.75 in x 17 in x 12.75 in (14.75" stage height)

Net Weight

:

21 kg (46.0 lb)

The S4022 is a compact, high-output band-pass subwoofer dedicated to permanent installations.

The system is equipped with two advanced 12” RCF precision woofers mounted in a clam-shell internal chamber.
The two transducers couple to achieve tight and maximised output. Each 12” features massive ceramic magnets and 3” copper voice coil.
The system is capable of producing a Max SPL of 131 dB and handles 800 Watts AES.
 

Features
Compact, arrayable, 2 x 12" bandpass subwoofer system
131 dB max SPL, 800 Watt AES
Equipped with RCF high power 2 x12“, 3" voice coil woofers
Extensive internal bracing, 8 x M10 mounting points
Recessed handles
Baltic Birch cabinet finished in a very resistant, textured, polyurethane black paint
Epoxy powder coated front grille
Dedicated to permanent installation

 

Acoustical Specifications
Frequency Response -10 dB:40 Hz÷ 0.2 kHz
Max SPL @ 1m:131 dB 
System Sensitivity:97 dB 
Nominal Impedance:4 Ω 
Power Handling:800 Watt 
Peak Power Handling:2400 Watt 
Recommended Amplifier:1600 
TRANSDUCERS
Woofer:2 X 12" woofer, 3" voice coil 
Nominal Impedence:8 Ω 
Input Power Rating:400 Watts AES 
Sensitivity:97 dB 
INPUT SECTION
Input connector:2 x Speakon NL4 
CABINET
Cabinet Material:15 mm birch plywood construction 
Hardware:8 x m10 mounting points, 2 x recessed 
Handles:2 seitlich 
Grille:Custom perforated steel grille 
Colour:Black, scratch resistant paint 
PHYSICAL SPECIFICATIONS
Height:500 / 19.68 mm/inch 
Width:650 / 25.59 mm/inch 
Depth:580 / 22.83 mm/inch 
Net Weight:38 / 83.77 Kg/Lbs

 

The S4012 high-efficiency band pass subwoofer is the ideal bass frequency extension to complement the RCFACUSTICA Compact series two-way loudspeakers for small size installations and distributed music systems.

The low-frequency transducer is an RCF Precision high-power 12” woofer with a 3” inside/outside voice coil to minimize power compression and extend the life of the product.
This new woofer design guarantees a fast and controlled reproduction of the bass frequency range. Using bandpass loading to the transducer, the subwoofer design ensures an efficient acoustic response down to 45 Hz.
The cabinet features two Neutrik Speakon™ connectors in a recessed input plate.

APPLICATIONS
  • • Low Frequency Enhancement
  • • Music Enhancement
  • • Special Effects Reinforcement
  • • Entertainment Systems
  • • Live Music Reinforcement
  • • Small Club Sound Systems
  • • Infill Sub Bass Enhancement

Γενικά Χαρακτηριστικά

  • 12" high-efficiency RCF Precision 3" voice-coil woofer with Inside/Outside Coil Technology
  • Horn reflex loaded woofer
  • 124 dB maximum sound pressure level
  • Response down to 45 Hz
  • Rectangular box enclosure with protective metal grille
  • Baltic Birch cabinet with black, heavy duty, textured epoxy paint
  • 35 mm standard pole mount in top section of cabinet
  • Integrated hand carry points

Ακουστικά Χαρακτηριστικά

  • Frequency Response -10 dB:45Hz ÷ 200 Hz
  • Max SPL @ 1m:124dB
  • System Sensitivity:92dB
  • Nominal Impedance:8Ω
  • Power Handling:400W
  • Peak Power Handling:1600W
  • Recommended Amplifier:800W

Χαρακτηριστικά Καμπίνας

  • Cabinet Material:15 mm birch plywood construction
  • Handles:2 on side
  • Pole Mount/Cap:Yes
  • Grille:Custom perforated steel grille
  • Colour:Black, scratch resistant paint

Διαστάσεις/Βάρος

  • Height:360 / 14.17 mm/inch
  • Width:500 / 19.69 mm/inch
  • Depth:400 / 15.75 mm/inch
  • Net Weight:20 / 44 kg/lbs

Professional Sound Tools for Musicians
 
Professional Components
At the heart of the PREMIUM PR:O full-range cabinets is a new 1" driver with ultra-low-distortion
that renders a very natural-sounding image even at peak loads. The 60° x 40° horn to which this
driver is coupled ensures uniform system directivity that is sure to delight performing musicians,
sound techs, and audiences alike.

Professional Features
The new PREMIUM PR:O series? high-value interior is reflected in the exterior?s smart appearance
and modern appointments. The ergonomically shaped and positioned handles are recessed into the
enclosures, with no projecting parts or screws that could ruin auto upholstery. In addition, the full-range
models feature countersunk rigging points for fast, professional fixed installation. For added convenience,
the subwoofer is pre-fitted with threaded bushings to accept optionally available casters. The ingeniously
simple DuoTilt? pole mount gives you a choice of angles at which to aim the speakers directly at your
audience, but without the hassle and risk of wobbly tilt units.

Dynamic protection circuit for the highfrequency driver
PREMIUM PR:O Series mid/high units and monitors are equipped with special protective circuitry.
Located in the high-frequency signal path, it limits output levels whenever the 1" driver approaches
the overload threshold.

PREMIUM PR:O - PR:O 12 M
 
Description  For a band, monitors play an important role too. The classic
Description  monitor for vocals/guitar is a 12" monitor. The PREMIUM PR:O
Description  12 M monitor is designed without compromise exactly for this
Description  application to provide the highest possible level of on-stage
Description  performance.
Power handling capacity  RMS: 400 W
Power handling capacity  Program: 800 W
Frequency response within +/-3dB  70 Hz ? 19 kHz
Frequency response @ -10dB  63 Hz ? 19 kHz
Speaker  1x 12?
Impedance  8 Ohm
HF driver  1?
Axial sensitivity 1w/1m half-space  104 dB
Maximum SPL 10% THD half-space  128 dB
Crossover frequency  2 kHz/12 db Octave
Connections  2x Speakon
Dimensions (WxHxD)  39 cm x 55,5 cm x 38 cm
Dimensions (WxHxD)  15 1/4? x 21 3/4? x 15?
Weight  16 kg
Weight  35.2 lbs


Reloop's Active PA Set stands for mobile sound quality. The heart of the entire independent PA system is the massive 600 watt subwoofer module which in addition to a 38 cm speaker also accommodates a perfectly modulated final amplifier including limiter and diplexer. The 'highlights' of the Reloop Active PA system are the two 150 watt satellites.

features:
  • 600 watt RMS high-end active subwoofer satellite combination
  • Set consists of:
    1 x 300 watt RMS high-end active subwoofer
    2 x 150 watt RMS high-end active satellites
    2 x Aluminium loudspeaker stands
    2 x PA professional speaker cables
    1 x line cord


technical data:
    Subwoofer:

    - Type: active bandpass subwoofer
    - Frequency range: 35 Hz - 250 Hz
    - Acoustic pressure: 129 dB
    - Speaker: 38 cm (15“) "Long-Throw" woofer
    - Active electronic filter
    - Integrated diplexer
    - Opto limiter
    - Dynaclip protective system
    - Transportation wheels
    - Carrying handles
    - Inputs: 6.3 mm jack, XLR
    - Outputs: PA professional speaker cables
    - Dimensions: 447 x 542 x 640 mm
    - Weight: 48.5 kg

    Satellites:

    - Type: active 2-way system
    - Frequency range: 100 Hz - 18 kHz
    - Impedance: 4 ohm
    - Acoustic pressure: 119 dB
    - Speaker: 20.3 cm (8“) mid/low-frequency speaker, 2.54 cm (1“) tweeter
    - Connections: PA professional speaker cable
    - Dynamic protective system
    - Dimensions: 272.5 x 420 x 250 mm
    - Weight: 10 kg
Weight22.00 kg21.00 kg40.00 kg20.00 kg16.00 kg48.50 kg
DimensionsΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/Δ
Additional information
Βάρος 22.00 kg
Βάρος 21.00 kg
Βάρος 40.00 kg
Βάρος 20.00 kg
Βάρος 16.00 kg
Βάρος 48.50 kg