Content |
Μονοκάναλο equalizer εμπνευσμένο από το κλασικό Neve 1073, με ζεστό και μουσικό ήχο σε πολύ προσιτή τιμή.
Το EQ-73 αποτελεί ουσιαστικά το eq section του Neve 1073 χωρίς το φίλτρο high-pass, ενώ έχουν προστεθεί περισσότερες συχνότητες οι οποίες λειτουργούν με ρυθμίσεις stepped στα πρότυπα της vintage μονάδας για καλύτερη δυνατότητα ανάκλησης των ρυθμίσεων. Συνολικά, το εύρος των ρυθμίσεων είναι από 20Hz εως 24kHz με κέρδος +/-15dB για τις δύο χαμηλότερες μπάντες και +/-18dB για την υψηλή μπάντα.
Συνδυάζοντας το Pre-73, το EQ-73 και ένα Unite Rack, έχετε την αυθεντική μονάδα Neve σε ασυναγώνιστη τιμή!
Χαρακτηριστικά:
- Vintage Style electronics
- Ρύθμιση stepped για την επιλογή συχνοτήτων
- Μεγάλο εύρος επιλογής από 20Hz ως 24kHz
- Εύρος ελέγχου -/+18dB
- Χωριστοί διακόπτες bypass για κάθε μπάντα
- Σχεδιασμένο για να χρησιμοποιείται με το insert jack του Pre-73
- TRS in/out jack, 18dBu nominal level
- Εξωτερική τροφοδοσία
- Κλασικός ήχος, ιδανικός για κάθε μουσικό στυλ
- Συμπαγής, ανθεκτική κατασκευή
|
DBX-1046
Compressor - limiter 4 εισόδων, κύκλωμα "overeasy“, peakstoplus,
είσοδοι - έξοδοι XLR και 1/4 TRS. Κατάλληλος για studio, live χρήση.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | Max Input | > +22 dBu balanced or unbalanced | CMRR | Typically >50 dB at 1 kHz | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | Output Type | Servo-balanced/unbalanced, RF filtered | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | Noise | | Dynamic Range | > 118 dB, unweighted | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | IMD | | Interchannel Crosstalk | | Stereo Coupling | True RMS Power Summing | Compressor Threshold Range | -40 dBu to +20 dBu | Compressor Ratio | 1:1 to infinity:1 | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | Compressor Attack/Release Characteristic | AutoDynamic™ | Compressor Attack Time | Program-dependent | Compressor Release Time | Program-dependent | Compressor Output Gain | -20 to +20 dB | Limiter Threshold Range | 0 dBu to +24 dBu (off) | Limiter Ratio | infinity:1 | Limiter Type | PeakStopPlus® two-stage limiter | Limiter Stage 1 | PeakStop® brickwall limiter | Limiter Stage 1 Attack Time | Zero | Limiter Stage 1 Release Time | Zero | Limiter Stage 2 | Predictive intelligent program limiter | Limiter Stage 2 Attack Time | Program-dependent | Limiter Stage 2 Release Time | Program-dependent | OverEasy® Switch | Activates the OverEasy compression function | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | Bypass Switch | Activates the direct input-to-output hard-wire bypass | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | Function Switches | LED indicator for each front-panel switch | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | Power Consumption | 20 Watts | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | Power Connector | IEC receptacle | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | Unit Weight | 5.2 lbs. (2.4 kg) | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
High-Definition 31-Band Stereo Graphic Equalizer with FBQ Feedback Detection System
- Professional 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies, e.g. floor rumble, hiss etc.
- Highly accurate 12-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard-bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving - 3-Year Warranty Program*
- Conceived and designed by BEHRINGER Germany
|
Νέα έκδοση S ηλεκτρονικού crossover 3 δρόμων με επιλεγόμενη συχνότητα cross, ρυθμιζόμενο input & output level, κλίση αποκοπής 24dB ανά οκτάβα, L & R είσοδοι & balanced έξοδοι με XLR.
More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 234xs Crossover you'll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world's finest processors. The 234xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 234xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 234xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs.
XLR balanced ins and outs
Mode switches for mono 4-way or stereo 2-way/3-way operation
Low frequency summed (subwoofer) output
x10 range switch on both channels
40Hz high pass (low cut) filter both channels
Phase reverse switch on all outputs
Individual level controls on all outputs
24dB per octave Linkwitz-Riley filters (the professional standard)
Stereo/Mono status LEDs indicate the selected mode
dbx® 2 year parts and labor as standard
CSA NRTL/C approved
CE compliant
Input Connectors | XLR | Input Type | Electronically balanced/unbalanced, RF filtered | Input Impedance | Balanced >50k ohm, unbalanced >25k ohm | Max Input | >+22dBu balanced or unbalanced | CMRR | >40dB, typically >55dB at 1kHz | Output Connectors | XLR | Output Type | Impedance-balanaced/unbalanced, RF filtered | Output Impedance | Balanced 200 ohm, unbalanced 100 ohm | Max Output | >+21dBu balanced/unbalanced into 2k ohms or greater | Bandwidth | 20Hz to 20kHz, +/-0.5dB | Frequency Response | 90 kHz, +0/-3 dB | Signal to Noise Ratio | Ref: +4 dBu, 22 kHz measurement bandwidth | Signal-to-Noise (Stereo Mode) | >94dB (Low Output), >93dB (Mid Output), >90dB (High Output) | Signal-to-Noise (Mono Mode) | >94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output) | Dynamic Range | > 106 dB, unweighted, any output | THD+Noise | | Interchannel Crosstalk | | Crossover Frequencies (Stereo Mode) | Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting) | Crossover Frequencies (Mono Mode) | Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz | Crossover Filter Type | Linkwitz-Riley, 24 dB/octave, state-variable | Low cut Switch | Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. | Phase Invert Switch | Inverts the phase at the output, one switch per output. | x1 / x10 Switch | Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. | Mode Switch | Selects stereo/mono and 2/3/4-way operation | LF Sum Switch | Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. | Indicators | Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) | Operating Voltage | 100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz | Operating Temperature | 32°F to 113°F (0°C to 45°C) | Power Consumption | 15W | Power Connector | IEC receptacle | Dimensions | 1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) | Unit Weight | 4.0 lbs. (1.8 kg) | Shipping Weight | 5.8 lbs. (2.6 kg) |
|
DBX 1215
Ισοσταθμιστής 2 x 15 περιοχών με XLR IN/OUT
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
| DBX 223XS
Ηλεκτρονικό crossover 2 δρόμων με επιλεγόμενη συχνότητα cross,
ρυθμιζόμενο input & output level, κλίση αποκοπής 24dB ανά οκτάβα,
L & R είσοδοι & balanced έξοδοι με XLR.
Overview
More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 223xs Crossover you\'ll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world\'s finest processors. The 223xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 223xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 223xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs
Features
- XLR balanced ins and outs
- Mode switch for stereo 2-way or mono 3-way operation
- Low frequency summed (subwoofer) output
- x10 range switch on both channels
- 40Hz high pass (low cut) filter both channels
- Phase reverse switch on all outputs
- Individual level controls on all outputs
- 24dB per octave Linkwitz-Riley filters (the professional standard)
- Stereo/Mono status LEDs indicate the selected mode
- dbx® 2 year parts and labor as standard
- CSA NRTL/C approved
- CE compliant
Specifications
Input Connectors |
XLR (pin 2 hot) |
Input Type |
Electronically balanced/unbalanced, RF filtered |
Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
Max Input |
>+22dBu balanced or unbalanced |
CMRR |
>40dB, typically >55dB at 1kHz |
Output Connectors |
XLR |
Output Type |
Impedance-balanaced/unbalanced, RF filtered |
Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
Bandwidth |
20Hz to 20kHz, +/-0.5dB |
Frequency Response |
< 3 Hz to > 90 kHz, +0/-3 dB |
Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >91dB (High Output) |
Signal-to-Noise (Mono Mode) |
>94dB (Low Output), >93dB (Mid Output), >91dB (High Output) |
Dynamic Range |
> 106 dB, unweighted, any output |
THD+Noise |
< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz |
Interchannel Crosstalk |
< -80 dB, 20 Hz to 20 kHz |
Crossover Frequencies (Stereo Mode) |
Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
Crossover Frequencies (Mono Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
Mode Switch |
Selects stereo/mono and 2/3-way operation |
LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
Operating Voltage |
100 VAC 50/60 Hz; 120 VAC 60 Hz 230 VAC50 HZ |
Operating Temperature |
32°F to 113°F (0°C to 45°C) |
Power Consumption |
15W |
Power Connector |
IEC receptacle |
Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
Unit Weight |
3.7 lbs. (1.7 kg) |
Shipping Weight |
5.4 lbs. (2.5 kg) |
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.