ARTSOUND MG05 P-mount Κεφαλή CZ-800-10, CR-800, Για Πικάπ Numark , ΙΟΝ

22.32 με ΦΠΑ 24%

Μόνο 5 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)

EAN: 4053171981902
Υπολογισμός δόσεων
CompareAdd to wishlist Υποβολή Καλύτερης Τιμής
Διαθεσιμότητα: Διαθέσιμο Διαθέσιμο Κωδικός προϊόντος: MG05 Κατηγορία:
MG05 Ανταλλακτική κεραμική κεφαλή για πικάπ ION CZ800-10, Numark Cr-800 κ.α. MG05 Replacement ceramic cartridge! This replacement ceramic cartridge is a perfect fit for your Classic LP, iPT01, iPTUSB, iPTUSB LE, Max LP, or Mobile LP and many other ION turntables (see list) To Replace Stylus Grasp both sides of the stylus and pull forward […]

 

Διαβάστε περισσότερα

MG05 Ανταλλακτική κεραμική κεφαλή για πικάπ ION CZ800-10, Numark Cr-800 κ.α.

MG05 Replacement ceramic cartridge!

This replacement ceramic cartridge is a perfect fit for your Classic LP, iPT01, iPTUSB, iPTUSB LE, Max LP, or Mobile LP and many other ION turntables (see list)

To Replace Stylus

  • Grasp both sides of the stylus and pull forward to remove stylus
  • Grasp both sides of the stylus and slide up and back to attach stylus

To Replace Cartridge

  • Remove stylus from old Cartridge
  • Grab headshell with thumb under front tab and index finger on rear of head shell with left hand.
  • Grab old cartridge with right thumb and index finger. Carefully Pull down and forward with right hand while while pulling up with left hand.
  • Carefully disconnect wires from rear of cartridge pulling from metal tabs.
  • Remove stylus guard and stylus from new cartridge
  • Connect wires on new cartridge. the single metal connector with black wires goes on the bottom posts that are closer together.
  • From rear view, as you would install the cartridge – The red wire goes on the right upper post, the white wire goes on the left upper post.
  • Reconnect cartridge to headshell by placing cartridge beneath headshell with thumb below cartridge and index finger on top of headshell.
  • Carefully squeeze the two together. a ‘light’ snap occurs and the cartridge should fit snug.
  • Reattach new stylus to new cartridge.

Fits all ION turntables that use a ceramic cartridge (see following list):

  • Classic LP
  • Max LP
  • Mobile LP
  • iPTUSB
  • Archive LP
  • Forever LP
  • Live LP
  • Power Play
  • Quick Play Flash
  • Quick Play LP
  • Vinyl Motion
  • Vinyl Motion Deluxe
  • Air LP
  • Duo Deck
  • iLP
  • LP 2 GO
  • CD Direct
  • iProfile
  • Profile LP
  • Profile Pro

*TTUSB, TTUSBDC, LP2CD, Select LP use a magnetic cartridge and are not compatible.

Η κατάλληλη ανταλλακτική βελόνα για 33/45rpm είναι η STY146

Βάρος 0.10 kg

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Κάνετε την πρώτη αξιολόγηση για το προϊόν: “ARTSOUND MG05 P-mount Κεφαλή CZ-800-10, CR-800, Για Πικάπ Numark , ΙΟΝ”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

Quick Comparison

ARTSOUND MG05 P-mount Κεφαλή CZ-800-10, CR-800, Για Πικάπ Numark , ΙΟΝ removeORTOFON Concorde Scratch ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM Scratch ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM PRO S ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM Digitrack ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeAUDIO TECHNICA AT33EV Κεφαλή πικαπ remove
NameARTSOUND MG05 P-mount Κεφαλή CZ-800-10, CR-800, Για Πικάπ Numark , ΙΟΝ removeORTOFON Concorde Scratch ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM Scratch ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM PRO S ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeORTOFON OM Digitrack ΚΕΦΑΛΗ ΜΕ ΒΕΛΟΝΑ removeAUDIO TECHNICA AT33EV Κεφαλή πικαπ remove
Imagemg05 cartrdge ion numark cz800 cr800
SKUMG05ConcordeScratchOMScratchOMPROSOMDigitrackAT33EV
Rating
Price22.32 με ΦΠΑ 24%102.00 με ΦΠΑ 24%64.00 με ΦΠΑ 24%49.00 με ΦΠΑ 24%67.00 με ΦΠΑ 24%635.12 με ΦΠΑ 24%
Stock

Μόνο 5 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)

Σε απόθεμα

Σε απόθεμα

Μόνο 1 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

AvailabilityΜόνο 5 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)Σε απόθεμαΣε απόθεμαΜόνο 1 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)Διαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίας
Add to cart

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Description
ContentMG05 Ανταλλακτική κεραμική κεφαλή για πικάπ ION CZ800-10, Numark Cr-800 κ.α. MG05 Replacement ceramic cartridge! This replacement ceramic cartridge is a perfect fit for your Classic LP, iPT01, iPTUSB, iPTUSB LE, Max LP, or Mobile LP and many other ION turntables (see list) To Replace Stylus
  • Grasp both sides of the stylus and pull forward to remove stylus
  • Grasp both sides of the stylus and slide up and back to attach stylus
To Replace Cartridge
  • Remove stylus from old Cartridge
  • Grab headshell with thumb under front tab and index finger on rear of head shell with left hand.
  • Grab old cartridge with right thumb and index finger. Carefully Pull down and forward with right hand while while pulling up with left hand.
  • Carefully disconnect wires from rear of cartridge pulling from metal tabs.
  • Remove stylus guard and stylus from new cartridge
  • Connect wires on new cartridge. the single metal connector with black wires goes on the bottom posts that are closer together.
  • From rear view, as you would install the cartridge - The red wire goes on the right upper post, the white wire goes on the left upper post.
  • Reconnect cartridge to headshell by placing cartridge beneath headshell with thumb below cartridge and index finger on top of headshell.
  • Carefully squeeze the two together. a 'light' snap occurs and the cartridge should fit snug.
  • Reattach new stylus to new cartridge.
Fits all ION turntables that use a ceramic cartridge (see following list):
  • Classic LP
  • Max LP
  • Mobile LP
  • iPTUSB
  • Archive LP
  • Forever LP
  • Live LP
  • Power Play
  • Quick Play Flash
  • Quick Play LP
  • Vinyl Motion
  • Vinyl Motion Deluxe
  • Air LP
  • Duo Deck
  • iLP
  • LP 2 GO
  • CD Direct
  • iProfile
  • Profile LP
  • Profile Pro
*TTUSB, TTUSBDC, LP2CD, Select LP use a magnetic cartridge and are not compatible. Η κατάλληλη ανταλλακτική βελόνα για 33/45rpm είναι η STY146

For DJs that require increased tracking ability, the Scratch is up to the task.  Featuring a reinforced rubber suspension, DJs need not worry about compromising sound quality and stylus life when working with higher tracking forces.  With solid bass reproduction and extended highs, the Scratch is great for any style, providing energetic, in-your-face sound.

Output voltage at 1000Hz, 5cm/sec.

7 mV

Channel balance at 1kHz

1,5 dB

Channel separation at 1kHz

25 dB

Channel separation at 15 kHz

15 dB

Frequency range at -3dB

20-20.000 Hz

Frequency response

20-15.000 Hz 3dB/-2dB

Tracking ability at 315 Hz at recommmende tracking force

80 μm

Compliance, dynamic lateral

6 μm/m N

Stylus type

Spherical

Stylus tip radius

R 18 μm

Tracking force range

3,0-5,0 g (30-50 mN)

Tracking force recommended

4,0 g (40 mN)

Tracking angle

20°

Internal impedance, DC resistance

750 Ohm

Internal inductance

450 mH

Recommended load resistance

47 kOhm

Recommended load capacitance

200-600 pF

Cartridge weight

18,5 g

Replacement stylus unit

Scratch

 

For DJs that require increased tracking ability, the Scratch is up to the task.  Featuring a reinforced rubber suspension, DJs need not worry about compromising sound quality and stylus life when working with higher tracking forces.  With solid bass reproduction and extended highs, the Scratch is great for any style, providing energetic, in-your-face sound.  

Output voltage at 1000Hz, 5cm/sec.

7 mV

Channel balance at 1kHz

1,5 dB

Channel separation at 1kHz

25 dB

Channel separation at 15 kHz

15 dB

Frequency range at -3dB

20-20.000 Hz

Frequency response

20-15.000 Hz 3dB/-2dB

Tracking ability at 315 Hz at recommmende tracking force

80 μm

Compliance, dynamic lateral

6 μm/m N

Stylus type

Spherical

Stylus tip radius

R 18 μm

Tracking force range

3,0-5,0 g (30-50 mN)

Tracking force recommended

4,0 g (40 mN)

Tracking angle

20°

Internal impedance, DC resistance

750 Ohm

Internal inductance

450 mH

Recommended load resistance

47 kOhm

Recommended load capacitance

200-600 pF

Cartridge weight

5 g

Replacement stylus unit

scratch

 

A budget cartridge that out performs a lot of other top-of-the-line models.

No need to go broke to get an affordable, tough-as-nails scratching tool.

Technical Data:

  • Output voltage at 1000 Hz, 5cm/sec: 5 mV
  • Channel balance at 1 kHz: 2 dB
  • Channel separation at 1 kHz: 20 dB
  • Channel separation at 15 kHz: 15 dB
  • Frequency range at - 3dB: 20-20.000 Hz
  • Frequency response: 20-18.000 Hz + 3 / - 2 dB
  • FIM distortion at recommended
    tracking force, DIN 45.542:
  • Tracking ability at 315Hz at
    recommended tracking force: 70 µm
  • Compliance, dynamic, lateral: 7 µm/mN
  • Stylus type: Spherical
  • Stylus tip radius: R 26 µm
  • Equivalent stylus tip mass: 0,5 mg
  • Tracking force range: 3,0-5,0 g (30-50 mN)
  • Tracking force, recommended: 4,0 g (40 mN)
  • Tracking angle: 20°
  • Internal impedance, DC resistance: 750 Ohm
  • Internal inductance: 450 mH
  • Recommended load resistance: 47 kOhm
  • Recommended load capacitance: 200-600 pF
  • Cartridge colour: Black
  • Cartridge weight: 5 g
  • Replacement stylus unit: PRO S

The newest cartridge from Ortofon, the DigiTrack responds to the next generation of turntable DJs who make extensive use of timecoded vinyl applications, such as Serato (TM) and FinalScratch (TM).  With DigiTrack's low wear design and tailored frequency response increase the lifespan of timecoded vinyl records, and provides high quality sound reproduction for playing conventional vinyl records as well.   DigiTrack also features excellent groove-handling capabilities for scratch and mix performance, as well as increased output voltage for improved TCV performance and better sound quality from your mixer's phono preamps.

Output voltage at 1000Hz, 5cm/sec.

8 mV

Channel balance at 1kHz

1,5 dB

Channel separation at 1kHz

22 dB

Channel separation at 15 kHz

15 dB

Frequency range at -3dB

20-20.000 Hz

Frequency response

20-20.000 Hz +/- 1,5 dB

Tracking ability at 315 Hz at recommmende tracking force

90 μm

Compliance, dynamic lateral

12 μm/m N

Stylus type

Spherical

Stylus tip radius

-

Tracking force range

2,0-4,0 g (20-40 mN)

Tracking force recommended

3,0 g (30 mN)

Tracking angle

-

Internal impedance, DC resistance

-

Internal inductance

-

Recommended load resistance

-

Recommended load capacitance

-

Cartridge weight

5 g

Replacement stylus unit

Digitrak

 

Σώμα: Aluminium / Synthetic Resin

Τύπος: Dual Moving Coil

Πηνία: PCOCC

Cantilever: Duralumin

Έξοδος: 0.3 mV

Απόκριση Συχνότητας: 15Hz - 50KHz

Διαχωρισμός καναλιών: 30 dB

Ισορροπία καναλιών: 0.5 dB

Βάρος Ανάγνωσης: 1.8-2.2 gr (standard 2.0 gr)

Εσωτερική Αντίσταση: 10 Ω

Συνιστώμενη Αντίσταση: 100 Ω

Ενδοτικότητα: 10 x 10-6 cm/dyne

Βάρος: 6.9 gr

Weight0.10 kg0.18 kg0.10 kg0.50 kg0.50 kg0.05 kg
DimensionsΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/Δ
Additional information
Βάρος 0.10 kg
Βάρος 0.18 kg
Βάρος 0.10 kg
Βάρος 0.50 kg
Βάρος 0.50 kg
Βάρος 0.05 kg