Content |
"When I run my guitar into two amps simultaneously, I always get a loud hum". This is a rather common problem, often discussed in the technology section of relevant industry magazines. The Palmer Y box is the solution. Converting the hi-Z guitar signal, the FET input circuitry also drives a transformer which routes the ungrounded signal to the output to eliminate ground loop hum. 9V battery operation is recommended.
The PGA03 Y-box can also be used as a line driver for long cable runs. Also, the PGA03 features a phase reverse switch for the AMP 2 output when using pre-amps or amps that are out of phase.
Technical specifications:
Input connectors
6.3 mm jack
Number of split-outputs per canal
1
Output connectors
6.3 mm jack
Transformer isolated outputs
Yes
Controls
ground lift, phase
Operating voltage
9 V block, 9 V DC power supply
Cabinet material
sheet steel
Cabinet surface
Powder coated
Optional Power Supply PW9V
Can be operated with a power supply unit (not included) or with batteries. “I always get a loud hum when I hook up both my amps…“. A rather common problem! We’ve got the answer !! The Palmer Y-box’s FET input circuitry adapts your guitar signal, driving a transformer which routes the ungrounded signal to the output. Ground hum is eliminated. 9V battery operation is recommended. The Y-box also serves as a line driver for long leads, and it allows for phase reversal of the AMP 2 output. This comes in handy when you’re using two (pre-) amps. |
Βάση ενισχυτή κιθάρας σε σχήμα 'X' με ρυθμιζόμενο το πίσω μπράτσο.
Εφαρμογή: | Ενισχυτής | Τύπος: | Ρυθμιζόμενη | Είδος: | Μονή |
|
Also available as 2, 4 and 16 Ohm Versions
Special DI box with loadbox for guitars. The integrated load resistor permits tube amplifiers up to approximately 120 W to be connected to the PGA04, bypassing a loudspeaker. A jack socket (unbalanced) and balanced XLR connector are available for direct pickup of the signal. The extensive filter section provides for a realistic simulation of classic guitar loudspeaker sounds.
Technical specifications:
- Loadbox: 6.3 mm jack input with parallel THRU socket for speaker operation Loadbox
- Input impedance: 8 ohms, max.
- Input load: 120 w RMS
- Input level display: 6 LED's
- Output: 2 x 6.3 mm jack, unbalanced, floating ground, 1 x balanced XLR output
- Output impedance: jack: 10.000 ohms, XLR: 600 ohms
- Level: unbalanced 0 dB, balanced -10 dB at 25 w
- Input Controls: Volume FiIlter, LOW, HIGH, LITE/BROWN-switch for tone shaping
- Full Range Volume for unfiltered signal, used in conjunction with the HI-CUT to emulate the bright sound of, e.g., 10-inch speakers
- Both signals attenuable
|
Χαμηλή βάση ενισχυτή κιθάρας
Ύψος πρόσθιου τμήματος: 21 - 28cm
Ύψος οπίσθιου τμήματος: 29 - 47.2cm
Πλάτος : 49cm
Ύψος διπλωμένη: 56cm
Σωλήνας πλαισίου: 20 x 15 mm
Σωλήνας ραφιών: 28mm
Μέγιστο φορτίο: 45.2 kg
Βάρος: 3 kg
|
The concept behind the cab merger may be very simple, but it fills an important gap!
Have you ever wanted to connect two guitar cabinets to one amplifier output? The PCABM makes it possible.
In addition, you can select whether the cabinets should be wired in parallel or series with one another. For example, if you interconnect two 8 ohm cabinets. The PCABM offers you two resulting impedances to choose from: 4 ohms (parallel) or 16 ohms (serial). The device is passive and does not affect the tone in any way.
- Type: passive
- Number of inputs: 2
- Input connections: 6.3mm jack
- Number of outputs: 2
- Output connections: 6.3mm jack
- Cabinet material: die-cast aluminium
- Case surface: powder-coated
- Width: 105 mm
- Depth: 35 mm
- Height: 35 mm
|
Πρακτική, εύχρηστη και σταθερή βάση για άλτο σαξόφωνα (Εb). Κατασκευή από αλουμίνιο με προστατευτικά λάστιχα στο σημείο που εφάπτεται το σώμα και η καμπάνα του σαξοφώνου προς αποφυγή τραυματισμού του οργάνου. Αναδιπλώνεται τόσο, έτσι ώστε να τοποθετηθεί στην θήκη του από βελούδο και στη συνέχεια μέσα στην καμπάνα του οργάνου για εύκολη μεταφορά.
Διαστάσεις: 310 mm ύψος, 0.3 kg βάρος |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.