PALMER PHDA02 Pro PHDA 02 – Reference Class Headphone Amplifier – 1-channel

353.91 με ΦΠΑ 24%

Διαθέσιμο κατόπιν παραγγελίας

EAN: 4049521090677
Υπολογισμός δόσεων
CompareAdd to wishlist Υποβολή Καλύτερης Τιμής
The PHDA02 – a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes. In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono […]

 

Διαβάστε περισσότερα

The PHDA02 – a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.

In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.

The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.

Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.

The PHDA02 is equipped with low-noise op amps, and the output amplifiers’ discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.

 


 

Βάρος 1.58 kg

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Κάνετε την πρώτη αξιολόγηση για το προϊόν: “PALMER PHDA02 Pro PHDA 02 – Reference Class Headphone Amplifier – 1-channel”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

Quick Comparison

PALMER PHDA02 Pro PHDA 02 - Reference Class Headphone Amplifier - 1-channel removeLD Systems HPA 6 - 19" Headphone Amplifier 6-channel ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ removeART MyMONITOR PERSONAL HEADPHONE MONITOR MIXER removePRESONUS HP-4 Προενισχυτής Ακουστικών 4 καναλιών removeVOX AMPLUG JOE SATRIANI ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ removeKRAMER VM-50H 1:5 Stereo Headphone Distribution Amplifier ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ remove
NamePALMER PHDA02 Pro PHDA 02 - Reference Class Headphone Amplifier - 1-channel removeLD Systems HPA 6 - 19" Headphone Amplifier 6-channel ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ removeART MyMONITOR PERSONAL HEADPHONE MONITOR MIXER removePRESONUS HP-4 Προενισχυτής Ακουστικών 4 καναλιών removeVOX AMPLUG JOE SATRIANI ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ removeKRAMER VM-50H 1:5 Stereo Headphone Distribution Amplifier ΕΝΙΣΧΥΤΗΣ ΑΚΟΥΣΤΙΚΩΝ remove
Image
SKUPHDA02LDHPA6AT/EM/000035HP4 EUVOX AMPLUG JOE SATRIANIVM-50H
Rating
Price 353.91 με ΦΠΑ 24% 212.03 με ΦΠΑ 24% 108.00 με ΦΠΑ 24% 138.87 με ΦΠΑ 24% 36.00 με ΦΠΑ 24% 264.66 με ΦΠΑ 24%
Stock

Διαθέσιμο κατόπιν παραγγελίας

Μόνο 2 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

AvailabilityΔιαθέσιμο κατόπιν παραγγελίαςΜόνο 2 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)Διαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίας
Add to cart

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Description
Content

The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.

In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.

The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.

Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.

The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.

 


 

LDHPA6 6-Channel Rackmount Headphone Amplifier

The LD Systems HPA 6 is a highly flexible 1U 19" rack format headphone amplifier with 6 fully independent channels and comprehensive features for a wide range of professional audio monitoring applications.

Each channel provides a 6.3 mm TRS headphone output on the front panel with level control, mono/stereo switching, discrete left/right muting  and a 6.3 mm TRS Aux input with Main/Aux balance control  for mixing in further signal sources. Four-segment LED meters permit visual output level monitoring, and two 6.3 mm TRS outputs per channel on the rear allow for connecting a total of 18 headphones.

The HPA 6\'s main section features a master level control with eight-segment LED metering  and 6.3 mm TRS input to mix in an additional source with all channels. The rear panel provides the main stereo inputs on balanced XLR and 6.3 mm TRS connectors and stereo outputs for daisy chaining multiple units.

  • Type: 6-channel
  • Inputs: Main Input (Stereo), Direct In (Stereo), 6 x Aux In (Stereo)
  • Input Connections: XLR and 6.3 mm jack L&R (Main Input, balanced), 6.3 mm stereo jack (Direct In), 6.3 mm stereo jack (Aux In)
  • Input Impedance: 13 kOhm
  • Line Outputs: Main Output (stereo, balanced)
  • Line Output Connectors: XLR and 6.3 mm jack L&R
  • Headphone Outputs: 6 x 3
  • Headphone Output Connectors: 6.3 mm stereo jack
  • Power Output: 6 x 125 mW
  • Minimal Connected Impedance per Channel: 8 ohms
  • Frequency Response: 20 Hz - 20.000 Hz
  • Controls: Main Input Level, 6 x Input Mix Main/Aux, 6 x Headphone Level, 6 x Mono Switch, 6 x Mute L&R, Power
  • Indicators: Main Input/Direct In Level Meter (8-segment LED chain), 6 x channel level meter (4-segment LED chain), 6 x mono LED, 6 x Mute L&R LEDs, Power LED
  • Power Supply: IEC power socket
  • Operating Voltage: 220 - 240 V AC, 50 - 60 Hz / 110 - 120 V AC, 50 - 60 Hz
  • Power Consumption: 40 W
  • Cabinet Material: metal
  • Cabinet Surface: painted
  • Width: 483 mm
  • Height: 44 mm
  • Depth: 217 mm
  • Accessories (included): power cord

Monitor Mixer Ακουστικών

Πρόβλημα: Ο μουσικός χρειάζεται να ακούει το όργανο του με ακουστικά, μεμονωμένα ή μιξαρισμένο από την έξοδο της κονσόλας, την έξοδο ενός CD player, ή οποιαδήποτε άλλη στέρεο πηγή. Στην κεντρική κονσόλα όμως, πηγαίνει μόνο το σήμα μικροφώνου.

Λύση: Συνδέστε το MyMONITOR ανάμεσα στο μικρόφωνο ,την line πηγή και την κονσόλα .Οι στάθμες εντάσεως καθώς και μίξης του μικροφώνου και line πηγής μπορούν να ρυθμιστούν μέσω ακουστικών. Το MyMONITOR μπορεί να τροφοδοτηθεί μέσω μπαταρίας ή τροφοδοτικού AC και μπορεί να χρησιμοποιηθεί οπουδήποτε, όπως από ένα μεγάλο φεστιβάλ ή σε εφαρμογές όπου δεν υπάρχει η δυνατότητα τροφοδότησης ηλεκτρικού ρεύματος. Δεν υπάρχει περιορισμός στην σύνδεση τύπων μικροφώνων. Εκτός από δυναμικά μπορούν να συνδεθούν και πυκνωτικά μικρόφωνα, καθώς η απαιτούμενη τροφοδοσία 48V μπορεί δοθεί από την κονσόλα μας ή οποιαδήποτε άλλη συσκευή οπού έχει αυτήν την δυνατότητα .



MyMONITOR - Personal Headphone Monitor Mixer Overview

Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.

MyMONITOR - Personal Headphone Monitor Mixer Specifications:

Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)

Το HP-4 της Presonus είναι η απάντηση στην ανάγκη για πολυκάναλο επαγγελματικό προενισχυτή ακουστικών, σε μικρό μέγεθος και προσιτή τιμή. Διαθέτει 4 εξοδους ακουστικών στο μπροστινό μέρος και η κάθε μια έχει το δικό της ποντεσιόμετρο για την αυξο,είωση της έντασης του ήχου και 150mW προενίσχυσης ανά κανάλι. Το HP-4 επίσης διαθέτει και volume control για τα monitor στο control room, διακόπτη monitor mute και διακόπτη mono προσφέροντάς σας έτσι μια πανίσχυρη και ολοκληρωμένη monitoring λύση σε μια απίστευτα χαμηλή τιμή.


 

Μίνι ενισχυτής ακουστικών για κιθάρα JOE SATRIANI signature, με τεχνολογία analog modeling εξομοίωσης με κύκλωμα High-Gain UK amp. Είσοδος AUX για σύνδεση με εξωτερική πηγή ήχου. Λειτουργία με 2xAAA μπαταρίες.

Specifications
  • Power supply: AAA batteries (x 2)

  • Battery life (FX on):
    Zinc-carbon batteries: approximately 3 hours
    Alkaline batteries: approximately 11 hours

  • Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22"

  • Weight: 40 g/1.41 oz. (not including batteries)

  • Included items: Two AAA batteries (for verifying operation)

 

Τεχνικά Χαρακτηριστικά: INPUT: 1 audio stereo, on 6.5mm stereo phone socket.
OUTPUTS: 5 audio stereo, on 6.5mm stereo phone sockets.
CONTROL: 5 stereo output level controls (front), 1 Mono switch (rear).
GAIN RANGE: 70 dB (- 60dB to +10dB).
16.5cm x 12cm x 4.5cm
0.68 kg.

Weight1.58 kg3.00 kg0.59 kg2.00 kg0.40 kg0.68 kg
DimensionsΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/Δ
Additional information
Βάρος 1.58 kg
Βάρος 3.00 kg
Βάρος 0.59 kg
Βάρος 2.00 kg
Βάρος 0.40 kg
Βάρος 0.68 kg