| Content |
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
| Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
- All-passive volume control circuit
- Stereo and AUX inputs
- Dual outputs
- Additional mono output
- Balanced and unbalanced connection
- Integrated high quality headphone amplifier
- Mono, mute and PFL switches
- Stereo volume, AUX and headphone level controls
- Elegant design with solid wood side panels
- Built to last
The Palmer Monicon® L is a precise, analogue volume control that connects between a computer or audio interface and active monitor speakers. The switch is completely passive and distortion-free, the LED displays and built-in headphone amplifier are powered via the included power supply.
Symmetric combo sockets serve as stereo input. The Monicon® L’s AUX input features RCA sockets and a 3.5 mm stereo jack. The compact console offers outputs for two monitor pairs and a mono summed output via XLR sockets. The stereo or AUX input can be selected alternately, the two outputs individually and together. In addition to its large volume controller, the Monicon® L is also equipped with mono, mute and PFL switches, a 6.35 mm headphone output, and separate AUX and headphone controllers for convenient operation.
Product type
Other Studio and Recording Equipment
Channels
2
Inputs
2
Input connectors
3.5 mm TRS , RCA , XLR
Input type
balanced/unbalanced (depending on TS/TRS connection)
Max. input level
20 dBu
Input impedance
(balanced) 10k Ohm(s) , (unbalanced) 5k Ohm(s)
Outputs
3
Output connectors
XLR
Output type
balanced/unbalanced (depending on TS/TRS connection)
Max. output level
20 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 40000 Hz
THD
0.001 %
Max. attenuation
(Attenuator + Mute) 112 dB , (Attenuator) 85 dB
Controls
attenuation , input selector , mono , mute , output selector , PFL source
Cabinet material
sheet steel , wood
Cabinet surface
Powder coated
Width
218 mm
Height
77 mm
Depth
100 mm
Weight
1,14 kg |
Φορητός ενισχυτής Ακουστικών υψηλής ποιότητος. Διαθέτει 3 ανεξάρτητες εξόδους ακουστικών (1/4 TRS η μία μπορεί να είναι 1/8 TRS) με έλεγχο στάθμης στη κάθε μια, ένδειξη peak σε κάθε έξοδο, επιλογή λειτουργείας mono/stereo, 1 είσοδο Line XLR, 1 unbalanced είσοδο Line 1/4 TRS, 1 unbalanced είσοδο 1/8 TRS, έξοδο Loop για να συνδεθεί με άλλη HX- 3, έξοδο balanced TA3 line / tape, Λειτουργεί με 2 μπαταρίες ΑΑ η με εξωτερικό 5-18 VDC.
| Αριθμός Εισόδων | 0 | | Τύπος Εισόδου | | | Βύσμα Εισόδου | | | Προενίσχυση Μικροφώνου | | | Τροφοδοσία Phantom | | | Ενδεικτικά Όργανα | | | Αριθμός Εξόδων | 0 | | Τύπος Εξόδου | | | Βύσμα Εξόδου | | | Τροφοδοσία | | | Ιδιαίτερα Χαρακτηριστηκά |
|
Overview
Sound can be perfected with Sennheiserʼs HDVA 600. Delivering authentic sound in its purest form, listeners are treated to a world of sheer listening pleasure. Years of knowledge in audio engineering and innovations in acoustic amplification, resulted in the creation of the HDVA 600. The consistently symmetrical signal processing and extremely low harmonic distortion guarantees an absolutely precise sound. Also, thanks to their pre-amp performance, they are easy to adjust and be connected directly to speakers for optimum audio amplification. In essence, the HDVA 600 provides a spectacular listening experience when paired with any Sennheiserʼs audiophile headphones.
Features
Consistently symmetrical signal processing for maximum sound quality
Symmetrical inputs and outputs simplify integration into a system
High-end ALPS quadruple potentiometer achieve perfect channel equality
Variable gain factor (five stages) for optimized use of low impedance headphones
Sophisticated metal housing to protect against signal scatter and vibration
Solid controls turned from solid metal, providing the utmost in long-term stability | The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped.
In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation.
A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback.
The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
- Model Name: LDHPA1
- Product Type: headphone amplifier
- Type: 1-channel stereo
- Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
- Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
- Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
- Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
- Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
- Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
- Headphone Outputs: 1
- Headphone Output Connectors: 3.5 mm stereo jack
- Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
- Minimal Connected Impedance per Channel: 16 ohms
- Frequency Response: 20 Hz - 40,000 Hz
- THD 1 kHz Sine: 0.04%
- Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
- Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
- Power Supply: 9 V DC block battery, DC jack
- Operating Voltage: 9 V DC
- Power Consumption: Nom. 70 mA / Max. 150 mA
- Housing Material: plastic
- Housing Surface: soft-touch
- Housing Colour: black
- Width: 80 mm
- Height: 42.5 mm
- Depth: 133 mm
- Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.