PALMER PLI05 Pro Balun – Line Isolation Box 2 Channel

119.29 με ΦΠΑ 24%

Διαθέσιμο κατόπιν παραγγελίας

EAN: 4049521049354
Υπολογισμός δόσεων
CompareAdd to wishlist Υποβολή Καλύτερης Τιμής
Διαθεσιμότητα: Διαθέσιμο 4-10 Ημ. Διαθέσιμο 4-10 Ημ. Κωδικός προϊόντος: PLI05 Κατηγορία:
Balanced or unbalanced isn’t the question here. BALUS stands for Balanced-Unbalanced. Due to the stereo TRS jacks used in the PLI05, it can cope with both balanced and unbalanced signals. The PLI05 is so to say the PLI02’s little sister. Both boxes can be used to convert balanced to unbalanced and both use so called […]

 

Διαβάστε περισσότερα

Balanced or unbalanced isn’t the question here. BALUS stands for Balanced-Unbalanced. Due to the stereo TRS jacks used in the PLI05, it can cope with both balanced and unbalanced signals. The PLI05 is so to say the PLI02’s little sister. Both boxes can be used to convert balanced to unbalanced and both use so called line isolating transformers to realize a galvanic separation. They are connected between mains powered devices to reliably prevent ground loop hum. The PLI02 was designed for use with XLR connections and for low impedances (600 Ohms). The PLI05 on the other hand with its jack connector is better for higher impedances. It covers a wide range from 600 Ohms to over 10 k Ohms. The attached diagrams for harmonic distortion, frequency- and phase characteristics demonstrate this quite
clearly. To prevent loss of level make sure that your input impedance is not higher than the output impedance. Both devices are suitable for high levels of up to +20dBu.
Product type
Line Isolators
Channels
2
Inputs
2
Input connectors
6.3 mm jack
Input type
balanced/unbalanced (depending on TS/TRS connection)
Input impedance
10k Ohm(s)
Max. input level
+ 6 dBu
Outputs
2
Output connectors
6.3 mm jack
Output type
balanced/unbalanced (depending on TS/TRS connection)
Output impedance
600 Ohm(s)
Max. output level
+ 6 dBu
Transformer balanced
Yes
Ratio
1:1
Frequency response
20 – 20.000 Hz
Cabinet material
Die-cast aluminium
Cabinet surface
Powder coated
Width
120 mm
Depth
60 mm
Height
35 mm
Weight
0,28 kg

 

 

Βάρος 0.5 kg

Αξιολογήσεις

Δεν υπάρχει καμία αξιολόγηση ακόμη.

Κάνετε την πρώτη αξιολόγηση για το προϊόν: “PALMER PLI05 Pro Balun – Line Isolation Box 2 Channel”

Η ηλ. διεύθυνση σας δεν δημοσιεύεται. Τα υποχρεωτικά πεδία σημειώνονται με *

Quick Comparison

PALMER PLI05 Pro Balun - Line Isolation Box 2 Channel removePalmer MI PDI 09 Passive DI Box for Guitars removeALPHATON IA-2 INLINE TRANSFORMER XLRf/m W/GROUNDLIFT removePALMER PAN01 Passive DI-box removeALPHATON DI 1000 TUBE DI BOX removeSTEWART ADB1 ACTIVE D.I. BOX remove
NamePALMER PLI05 Pro Balun - Line Isolation Box 2 Channel removePalmer MI PDI 09 Passive DI Box for Guitars removeALPHATON IA-2 INLINE TRANSFORMER XLRf/m W/GROUNDLIFT removePALMER PAN01 Passive DI-box removeALPHATON DI 1000 TUBE DI BOX removeSTEWART ADB1 ACTIVE D.I. BOX remove
Image
SKUPLI05PDI09IA-2PAN01DI 1000ADB1E
Rating
Price 119.29 με ΦΠΑ 24% 100.06 με ΦΠΑ 24% 119.04 με ΦΠΑ 24% 52.07 με ΦΠΑ 24% 773.75 με ΦΠΑ 24% 164.56 με ΦΠΑ 24%
Stock

Διαθέσιμο κατόπιν παραγγελίας

Διαθέσιμο κατόπιν παραγγελίας

Σε απόθεμα

Μόνο 5 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)

Σε απόθεμα

Διαθέσιμο κατόπιν παραγγελίας

AvailabilityΔιαθέσιμο κατόπιν παραγγελίαςΔιαθέσιμο κατόπιν παραγγελίαςΣε απόθεμαΜόνο 5 απομένουν σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)Σε απόθεμαΔιαθέσιμο κατόπιν παραγγελίας
Add to cart

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Προσθήκη στο καλάθι

Description
ContentBalanced or unbalanced isn't the question here. BALUS stands for Balanced-Unbalanced. Due to the stereo TRS jacks used in the PLI05, it can cope with both balanced and unbalanced signals. The PLI05 is so to say the PLI02's little sister. Both boxes can be used to convert balanced to unbalanced and both use so called line isolating transformers to realize a galvanic separation. They are connected between mains powered devices to reliably prevent ground loop hum. The PLI02 was designed for use with XLR connections and for low impedances (600 Ohms). The PLI05 on the other hand with its jack connector is better for higher impedances. It covers a wide range from 600 Ohms to over 10 k Ohms. The attached diagrams for harmonic distortion, frequency- and phase characteristics demonstrate this quite clearly. To prevent loss of level make sure that your input impedance is not higher than the output impedance. Both devices are suitable for high levels of up to +20dBu.
Product type
Line Isolators
Channels
2
Inputs
2
Input connectors
6.3 mm jack
Input type
balanced/unbalanced (depending on TS/TRS connection)
Input impedance
10k Ohm(s)
Max. input level
+ 6 dBu
Outputs
2
Output connectors
6.3 mm jack
Output type
balanced/unbalanced (depending on TS/TRS connection)
Output impedance
600 Ohm(s)
Max. output level
+ 6 dBu
Transformer balanced
Yes
Ratio
1:1
Frequency response
20 - 20.000 Hz
Cabinet material
Die-cast aluminium
Cabinet surface
Powder coated
Width
120 mm
Depth
60 mm
Height
35 mm
Weight
0,28 kg
   

Passive DI box especially designed for guitars.

The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic "speaker" sound. Tone can be varied between "Mellow“, "Normal“, or "Bright“.

Technical specifications:

  • Input: 6.3 mm jack with parallel "THRU" socket
  • Output: male XLR transformer balanced
  • Attenuator: (Level switch) 0 dB for line signals, -15 dB for small amps up to 10 w, 30 dB for large amps up to 200 w
  • No battery necessary

Inline Transformer IA-2

The model IA-2 line matching transformers !S designed to properly match a low impedance
signal to a low impedance source. The advantage of "ground lift" switching allows to optmize
hum problems.
 
Technical Data
Frequency response 20 Hz - 20 KHz + 1 dB
Impedance 600 : 600 Ohm
THD K3 50 Hz = 0.5 %
Level < + 6 dBm
Weight 100 g
Dimensions diameter 17 mm, lenght 115 mm
 

Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.

Product type DI Boxes
Type passive
Channels 1
Inputs 1
Input connectors 6.3 mm Jack
Max. input level + 54 dBu
Input impedance (@ 60 Hz) 60k Ohm(s)
Input pad 0 / -30 dB
Outputs 1
THRU outputs/channel 1
Output connectors 6.3 mm Jack , XLR
Max. output level + 4 dBu
Output impedance 600 Ohm(s)
Frequency response 20 - 20000 Hz
Transformer balanced yes
Ratio 10 : 1
Controls attenuator , ground lift
Cabinet material sheet steel
Cabinet surface powder coated
Width 110 mm
Depth 73 mm
Height 42 mm
Weight 0,34 kg

 

Tube-buffered DI-Box DI-1000

The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of
musical interfaces without degrading the sound. This can only be achieved by
providing a very high input impedance to avoid any loading of instrument pickups.This
design approach allows seemingly infinite headroom to preserve the real dynamic range
of the interfaced instruments.A vacuum tube enables all these goals to be achieved
without any compromises in sound quality.The sonic difference between a standard
DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference
between a standard microphone and a studio microphone.One of the best transformers,
the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground
isolation. The parameters of this transformer, like frequency response, phase response,
group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
 
Technical Specifications
Input
The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input
impedance to prevent any signal degradation, inevitable in traditional designs.
Buffered Output“
The second stage of the vacuum tube is used to buffer the signal and lower the output
impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters
without loosing high frequency information.
Boost circuit
The boost circuit increases the signal send to the output transformer by 15 dB. This may
be useful for instruments with extremely low output, but decreases headroom capability
to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output
transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion
normally does not occur - but is sometimes desirable, being the reason for this special feature.
Unity circuit
The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer.
This gives the best possible sound quality.
Ground-lift“-Switch
This front panel mounted switch allows complete ground and electrical isolation between the
direct injection box and the console or recording device.
 

Mechanical Specifications
Cabinet 2 mm stainless steel
Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched
Dimensions 185 x 100 x 40 mm
Vibration insulation 4 high-compliance rubber-elements
Operating Voltage
220/110 V AC, selectable via rear panel mounted switch. The fuse is easily
accessible from the rear panel. IEC mains connector with optional fixture.
Construction details
Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors
and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks
and high performance switches ensure flawless operation. The power supply is optimised via
measurement quality toroid transformer and a low impedance design to ensure the lowest
possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear
blue LED perfects the aesthetics of the DI box.

Technical Data
Input impedance > 20 MOhm
Output impedance180 Ohm at 1 kHz
Frequncy response 20 Hz - 20 kHz (-0,1 dB)
                             5 Hz - 120 kHz (-3 dB)
THD at 0 dBv  0,06% at 20 Hz
                      0,04% at 1 kHz
                      0,035% at 20 kHz
Signal to Noise Ratio 86 dB
Tube ECC 83/7025 A - military E 83 CC optional
Output transformer JENSEN JT-DB-E
Polarity Pin 2 Hot , AES/IEC -Standard
Max. Input voltage > 30 V peak

The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to
directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors
can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality.
The ADB-1 operates on either phantom power or a 9-volt battery.

FEATURES:
Flat response
Low distortion
Low noise
Wide dynamic range
No transformer
RF protection on input and output
Switchable ground isolation
Flush mounted slide switches

Weight0.5 kg0.29 kg0.10 kg0.34 kg0.60 kg0.50 kg
DimensionsΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/ΔΜ/Δ
Additional information
Βάρος 0.5 kg
Βάρος 0.29 kg
Βάρος 0.10 kg
Βάρος 0.34 kg
Βάρος 0.60 kg
Βάρος 0.50 kg