| Content | Balanced or unbalanced isn't the question here. BALUS stands for Balanced-Unbalanced. Due to the stereo TRS jacks used in the PLI05, it can cope with both balanced and unbalanced signals. The PLI05 is so to say the PLI02's little sister. Both boxes can be used to convert balanced to unbalanced and both use so called line isolating transformers to realize a galvanic separation. They are connected between mains powered devices to reliably prevent ground loop hum. The PLI02 was designed for use with XLR connections and for low impedances (600 Ohms). The PLI05 on the other hand with its jack connector is better for higher impedances. It covers a wide range from 600 Ohms to over 10 k Ohms. The attached diagrams for harmonic distortion, frequency- and phase characteristics demonstrate this quite
clearly. To prevent loss of level make sure that your input impedance is not higher than the output impedance. Both devices are suitable for high levels of up to +20dBu.
Product type
Line Isolators
Input connectors
6.3 mm jack
Input type
balanced/unbalanced (depending on TS/TRS connection)
Input impedance
10k Ohm(s)
Output connectors
6.3 mm jack
Output type
balanced/unbalanced (depending on TS/TRS connection)
Output impedance
600 Ohm(s)
Max. output level
+ 6 dBu
Frequency response
20 - 20.000 Hz
Cabinet material
Die-cast aluminium
Cabinet surface
Powder coated
| Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer's Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
|
Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Product type
DI Boxes
Type
passive
Channels
1
Inputs
1
Input connectors
6.3 mm Jack
Max. input level
+ 54 dBu
Input impedance
(@ 60 Hz) 60k Ohm(s)
Input pad
0 / -30 dB
Outputs
1
THRU outputs/channel
1
Output connectors
6.3 mm Jack , XLR
Max. output level
+ 4 dBu
Output impedance
600 Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
yes
Ratio
10 : 1
Controls
attenuator , ground lift
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
110 mm
Depth
73 mm
Height
42 mm
Weight
0,34 kg
|
The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to
directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors
can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality.
The ADB-1 operates on either phantom power or a 9-volt battery.
FEATURES:
Flat response
Low distortion
Low noise
Wide dynamic range
No transformer
RF protection on input and output
Switchable ground isolation
Flush mounted slide switches | 2-channel passive DI box for line and loudspeaker levels. PAN-04 consists of a housing containing the equivalent of two PAN-01s, making it a dual channel passive DI box. This „stereo" configuration makes it ideally suited for use with certain keyboards and devices which have several outputs.ive DI box. Jack input with paralell „THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Specifications
- No. of channels: 2
- Passive/Actibe: Passive
- Transformer balanced: Yes
- Attenuator: -30 dB
- Input/Output Gain: -20 dB
- Ground lift switch: Yes
- Max Input Level: +54 dBu
- Max Output Level: +4 dBu
- Frequency Range 2K Source Imp. -1dB: 10 Hz - 40 kHz
- Input Impedance 60Hz: 60 kΩ
- Nom. Output Impedance: 600 Ω
- Housing: Steel
- Dimension: 110 x 110 x 45 mm
|
2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.