Content |
Rack mount μίκτης ενισχυτής 5 εισόδων, ισχύς 120W@100V,4x XLR MIC/LINE in, 1x line (RCA) in, έξοδο εγγραφής, ρυθμιστικά bass treble, 420x88x280mm, 7.8 Kg. |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 400: 2x 200 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 17 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
XV Series - Intelligent Power Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 1600: 2x 800 W / 100 V Class: AB Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans(temp. reg. variable speed) Weight: 39 kg Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | Current Consumption | 30 mA or less | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | Finish | Panel: Surface-treated steel plate | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | Weight | 50 g | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
|
Ενισχυτής ανακοινώσεων 250W. 24 ζωνών ψηφιακός, 24 έξοδοι επιλεγμένες με διακόπτη με ενσωματωμένο δέκτη FM, 1 CDP. 22 kg.
POWER AMP
|
Rated Output
|
120W + 120W
|
Input Sensitivity
|
-10dBV / 10kΩ
|
S/N
|
Better than 75dB
|
Frequency Response
|
100Hz-18kHz
|
MIC/LINE 1~5CH
|
MIC Input Sensitivity
|
-55dBV / 10kΩ
|
MIC S/N
|
Better than 55dB
|
MIC Frequency Response
|
120Hz-10kHz
|
MIC T.H.D
|
Less than 0.5%
|
LINE Input Sensitivity
|
-10dBV / 10kΩ
|
LINE S/N
|
Better than 65dB
|
LINE T.H.D
|
Less than 0.3%
|
CD
|
S/N
|
Better than 80dB
|
Frequency Response
|
100Hz-20kHz
|
TUNER
|
S/N
|
Better than 60dB
|
Frequency Response
|
120Hz-12kHz
|
Power Consumption
|
170W (1/8 Power)
|
Weight
|
16kg/35.3lb
|
Dimension
|
482(W)x177(H)x373(D)mm/19(W)x7(H)x15(D)in
|
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.