Content | Βασικά χαρακτηριστικά :
- Μετατρέψτε το Wireless GO σε φορητό μικρόφωνο
- Περιλαμβάνεται αντιανέμιο
- Για ENG
Μετατρέψτε τον ασύρματο πομπό GO σε φορητό μικρόφωνο με το RODE Interview GO. Μόλις ο πομπός τοποθετηθεί άνετα στη βάση του Wireless GO, ο προσαρμογέας θα σας δώσει τον ήχο και την εμφάνιση ενός φορητού μικροφώνου. |
The SMV Bag is designed to carry the Stereo VideoMic along with spare batteries, shock mount bands and other small accessories.
It features an adjustable and removable strap, belt loops, and is made from durable neoprene.
Weight 110.00gm
Dimensions 159.00mmH x 97.00mmW x 47.00mmD
|
Προενισχυτής ultra linear series εξαιρετικά χαμηλού θορύβου, απόκριση συχνότητας 10Ηz-30kΗz. Ρυθμιζόμενο gain +6,0,-10 dB και low cut 70 ή 150 Ηz. Τροφοδοτείται αυστηρά με phantom power 48V. Συνδυάζεται με τις κάψες CK 61, CK 62, CK 63, CK 69. |
Shure P4HW Ενσύρματο Bodypack Monitor
P4HW Wired Bodypack
Hardwired Bodypack
Key Features
Attached input cable
High-impact plastic chassis
Operating Controls:
Operating mode (Stereo, Mono, MixMode)
Volume knob
Balance knob
Defeatable limiter
High-frequency boost
-15 db Pad
Backlit LCD Indicators :
Battery life
Input level
Operating mode
Frequency Response
20 to 20,000 Hz
Total Harmonic Distortion
Channel Separation
35 dB (minimum)
Signal-to-noise ratio
85 dB (minimum)
Maximum Output Level
+5 dBu at 1% THD
Maximum Input Level
+7 dBu, input pad OFF
+22 dBu, input pad ON
Actual Input Impedance
> 40 kilohms
Audio Output Connector
3.5 mm stereo (left=tip, right=ring, ground=sleeve)
Power Requirements
9 V Alkaline battery
Battery Life
Up to 8 hours, volume dependant
Phantom Power Protection
Up to 60 VDC
| Battery power supply for two AKG or t.bone microphones with TQG connection
T.BONE L-PACK ΤΡΟΦΟΔΟΣΙΑ ΜΠΑΤΑΡΙΑΣ ΓΙΑ ΜΙΚΡΟΦΩΝΑ ΜΕ ΤΥΠΟ ΣΥΝΔΕΣΗΣ TQG
Balanced XLR output
2 three-pole TQG male inputs
Both inputs adjustable
On-off switch
Mic / Line level in the output switchable
9 V battery power
20 hours of operation with 1 battery
Power LED | Gravity MA 3D A POP 1 Traveler 3D Arm with Pop Filter
The Traveler Series' Pop Filter with 3D Arm
Every bit of weight counts when you're travelling by plane or truck from one gig to the next. After all, you can't always rely on the concert venue having the right tool available for you when needed.
The Pop Filter with 3D Arm MA 3D A POP 1 can be taken everywhere you go. It's so light and space-saving, there's absolutely no need for you to worry about weight or storage space.
With this tool you can enhance your voice- and vocal recordings by placing the high-quality pop filter, with double nylon mesh and a large screen diameter of 15.7 cm between you and your microphone. This way you avoid unwanted pop noises and clipping.
Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm lets you mount it on all popular microphone stands, and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws. Voila - you're all done! Once set, the MA 3D A POP 1 stays locked in place.
Gravity® has once again delivered a small, useful and reliable product for you to round off your collection of stands.
Product type |
Microphone Accessories |
Type |
Pop filter |
Material |
Plastic, Polyamide |
Color |
Black |
Joint adjustment |
Wing screw |
Joint rotation |
360° |
Joint tilt |
180° |
Arm length |
400 mm |
Suitable for mounting on |
Microphone Stands |
Thread size |
3/8” |
Screen diameter |
157 mm |
Setup |
Double nylon screen, plastic frame |
Suitable for tube diameter |
15 - 35 mm |
Weight |
0,377 kg |
|
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.