Reveal 6D A set of DIP switches on the rear control panel of the new Reveal D Active monitors allow the selection of an optimum speaker response for real life and often difficult monitoring situations so that the frequency response at the listener?s ears is always as linear and flat as possible. Reveal monitors can […]
Reveal 6D
A set of DIP switches on the rear control panel of the new Reveal D Active monitors
allow the selection of an optimum speaker response for real life and often difficult
monitoring situations so that the frequency response at the listener?s ears is always
as linear and flat as possible. Reveal monitors can therefore be optimised for varying
listening distances in difficult acoustic spaces; varying meter bridge positions, against
and adjacent to walls or reflecting surfaces, in corners, in corners on shelves or brackets,
table top / space restricted PC/Mac based sound editing environments and stand mounted
or soffit mounted configurations.
MAIN FEATURES
From the front:
40mm MDF sculpted baffle ? stiff, heavy and rigid and minimises diffraction.
Recessed drive units flush with the baffle surface ? minimises diffraction.
New tweeter has wide band design extending the amplitude response
beyond 20kHz audibility to 50kHz to correct the phase response from
8kHz to 20kHz within the audible band. This preserves the harmonic
structure of sounds and the stability of the stereo image.
Smooth tweeter faceplate contours prevent diffraction and cavity effects.
10 point fixing maximises contact between drive unit and baffle.
New design bass units have aluminium flux control rings around the
voice coils and copper caps on the pole pieces ? linearises the voice
coil motional impedance to reduce non linear (3rd order) distortion
products caused by varying voice coil inductance.
Bass unit development using Klippell? analysis equipment to
minimise offsets and linearise the suspension components.
On/Mute (energy saving mode) via the Tannoy logo push switch.
LED indicator shows Active/Energy Saving modes.
From the side:
18mm MDF cabinet construction provides stiffness and minimises colouration.
Internal construction braces the sides and rear of the cabinet against the rear
of the bass driver to provide a rigid reactive mass for the moving cone assembly.
Ensures fast tight bass response and clear midrange.
Front baffle and rear panel tongued and grooved into the cabinet as a mechanical
interlock for safety if wall mounted.
From the rear:
Double insulated to prevent ground loops ? no safety earth required.
CSA/CE/CCC/CB full safety approvals including China.
Spare fuse in IEC mains connector.
On/Off mains isolator switch.
Substantial heat sinking for long term cool running and 24/7 reliability.
XLR and 1/4? jack Combi connector for balanced input.
Switch adjacent to XLR selects digital or analogue input.
RCA input for SPDIF with 75 Ohm terminating impedance.
2nd RCA for SPDIF output for slaving a stereo pair.
Yellow LED indicator lights up when digital lock is achieved.
3-way switch selects which channel of the SPDIF stream is decoded,
marked Left/Right/Mono. Switching is post 2 channel DAC.
Trim/Gain control over +6dB/-12dB range reference 0dBV (0.775V)
input for full rated output.
Trim/Gain control works on SPDIF input post DAC.
Switch selection of 12dB/8ve 80Hz hi-pass filter for use with AV subwoofers.
First bank of 10 DIP switches controls LF alignment, mid/near/close field and
half/quarter/eighth space compensation.
Second bank of DIP switches controls mid band and HF shelving trim.
Note that the DIP switch flat setting is shown on the back panel artwork.
Small hole to the right of the right hand switch bank allows the factory set HF
trim on test to be fine trimmed by a service agent if a tweeter needs to be replaced.
TECHNICAL SPECIFICATIONS
PERFORMANCE
Frequency response (1) 60Hz-51kHZ
Max SPL (2) 115dB
Distortion
Βάρος
12.00 kg
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.
Κάνετε την πρώτη αξιολόγηση για το προϊόν: “TANNOY REVEAL-6D ACTIVE STUDIO MONITOR” Ακύρωση απάντησης
Reveal 6D
A set of DIP switches on the rear control panel of the new Reveal D Active monitors
allow the selection of an optimum speaker response for real life and often difficult
monitoring situations so that the frequency response at the listener?s ears is always
as linear and flat as possible. Reveal monitors can therefore be optimised for varying
listening distances in difficult acoustic spaces; varying meter bridge positions, against
and adjacent to walls or reflecting surfaces, in corners, in corners on shelves or brackets,
table top / space restricted PC/Mac based sound editing environments and stand mounted
or soffit mounted configurations.
MAIN FEATURES
From the front:
40mm MDF sculpted baffle ? stiff, heavy and rigid and minimises diffraction.
Recessed drive units flush with the baffle surface ? minimises diffraction.
New tweeter has wide band design extending the amplitude response
beyond 20kHz audibility to 50kHz to correct the phase response from
8kHz to 20kHz within the audible band. This preserves the harmonic
structure of sounds and the stability of the stereo image.
Smooth tweeter faceplate contours prevent diffraction and cavity effects.
10 point fixing maximises contact between drive unit and baffle.
New design bass units have aluminium flux control rings around the
voice coils and copper caps on the pole pieces ? linearises the voice
coil motional impedance to reduce non linear (3rd order) distortion
products caused by varying voice coil inductance.
Bass unit development using Klippell? analysis equipment to
minimise offsets and linearise the suspension components.
On/Mute (energy saving mode) via the Tannoy logo push switch.
LED indicator shows Active/Energy Saving modes.
From the side:
18mm MDF cabinet construction provides stiffness and minimises colouration.
Internal construction braces the sides and rear of the cabinet against the rear
of the bass driver to provide a rigid reactive mass for the moving cone assembly.
Ensures fast tight bass response and clear midrange.
Front baffle and rear panel tongued and grooved into the cabinet as a mechanical
interlock for safety if wall mounted.
From the rear:
Double insulated to prevent ground loops ? no safety earth required.
CSA/CE/CCC/CB full safety approvals including China.
Spare fuse in IEC mains connector.
On/Off mains isolator switch.
Substantial heat sinking for long term cool running and 24/7 reliability.
XLR and 1/4? jack Combi connector for balanced input.
Switch adjacent to XLR selects digital or analogue input.
RCA input for SPDIF with 75 Ohm terminating impedance.
2nd RCA for SPDIF output for slaving a stereo pair.
Yellow LED indicator lights up when digital lock is achieved.
3-way switch selects which channel of the SPDIF stream is decoded,
marked Left/Right/Mono. Switching is post 2 channel DAC.
Trim/Gain control over +6dB/-12dB range reference 0dBV (0.775V)
input for full rated output.
Trim/Gain control works on SPDIF input post DAC.
Switch selection of 12dB/8ve 80Hz hi-pass filter for use with AV subwoofers.
First bank of 10 DIP switches controls LF alignment, mid/near/close field and
half/quarter/eighth space compensation.
Second bank of DIP switches controls mid band and HF shelving trim.
Note that the DIP switch flat setting is shown on the back panel artwork.
Small hole to the right of the right hand switch bank allows the factory set HF
trim on test to be fine trimmed by a service agent if a tweeter needs to be replaced.
TECHNICAL SPECIFICATIONS
PERFORMANCE
Frequency response (1) 60Hz-51kHZ
Max SPL (2) 115dB
Distortion
The CMS 50 is the most compact monitoring loudspeaker of all the Focal Professional range. Its design permits listening from 50cm away, while still keeping the possibility of the monitors at a great distance from one another without damaging the soundstage. The 5” mid-woofer reaches down to 55Hz, while offering a controlled bass and a totally linear midrange. The midrange register of the CMS 50 has unequalled neutrality in its price range. The Al-Mg inverted dome tweeter offers outstanding dynamics and a degree of definition in the treble that allow precise measurement of reverb and other effects which are normally very difficult to assess.
Power ON / OFF LED
Standby / ON LED
Audio Clip LED
Woofer :
5" Focal drive unit, Polyglass cone
Tweeter :
Aluminum/Magnesium inverted dome Focal tweeter
Shielding :
Integral by cancellation magnet
Construction :
Reinforced and damped Aluminum cabinet
Finish :
Black powder cabinet
Dimensions with spikes :
289.5 x 190 x 201mm (11.4" x 7.5" x 7.9“)
Dimensions with table stand :
299.5 x 190 x 201mm (11.8" x 7.5" x 7.9“)
Net weight :
7.7kg - (17lb)
High-Resolution, Active 2-Way Reference Studio Monitor with 5.25" Kevlar Woofer
Ultra-linear studio monitor with true active design
Precision Class A/B amplifiers with active protection circuits: 50 W for LF / 25 W for HF
Ultra-high resolution, ferrofluid-cooled 1" dome tweeter for ultimate sound reproduction
Long-throw 5.25" woofer with deformation-resistant Kevlar cone for ultimate bass response
Ultimate dispersion characteristics and extremely large "sweet spot" owing to advanced wave guide technology
High-precision crossover network with 4th order Linkwitz-Riley filters
Adjustable to a wide range of acoustic conditions
Separately controlled limiter for low and high frequency overload protection
Magnetic shielding allows placement near computer monitors
“Planet Earth" power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
Servo-balanced inputs with XLR, 1/4" and unbalanced RCA connectors
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
Τεχνικλα χαρακτηριστικα:
Professional 2-way active DJ monitors
Output: 2 x 30 w RMS
Frequency response: 35 Hz - 20 kHz
S/N Ratio: > 75dB
Impedance: 8 ohm
Magnetically shielded bass drivers
Speakers: 13.34 cm (5.25“) bass, 2.54 cm (1“) tweeter
Dimensions: 232 x 320 x 180 mm
Weight: 5.0 kg (per piece)
Mackie HR624 MK2 ενεργό monitor δύο δρόμων ιδανικά για χρήση σε studio, με εξαιρετικά γραμμική απόκριση συχνότητας. Kαμπίνα MDFμε εσωτερική αντιστήριξη.
Χαρακτηριστικά:
6.7" high-precision, low-distortion LF driver
1" titanium dome ferrofluid-cooled tweeter
Optimized waveguide for wide, even tone
Twin FR Series amps: 100W LF, 40W HF
Cast aluminum Zero Edge baffle minimizes diffraction
Internal damping eliminates midrange artifacts
Acoustic Space Control, LF roll-off, HF shelf controls
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.